Page 1 EOS 70D (W) EOS 70D (N) * The EOS 70D (N) does not have the Wi-Fi functions explained in this manual. Basic Instruction Manual This basic manual covers only the most basic operations. For other features and more details, see the Camera Instruction Manual pdf file in the CD-ROM.
Page 2: Introduction
After shooting, play images back and check whether they have been properly recorded. If the camera or memory card is faulty and the images cannot be recorded or downloaded to a computer, Canon cannot be held liable for any loss or inconvenience caused.
Page 3: Compatible Cards
Compatible Cards The camera can use the following cards regardless of capacity: • SD memory cards • SDHC memory cards* • SDXC memory cards* * UHS-I cards supported. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table.
Page 4: Item Check List
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Battery Pack Battery Charger LP-E6 LC-E6/LC-E6E* Camera (with protective cover) (with body cap) Interface Cable Wide Strap EW-EOS70D * Battery Charger LC-E6 or LC-E6E is provided.
Page 5: Instruction Manual And Cd-Roms
Instruction Manual and CD-ROMs The instruction manual consists of booklets and electronic manuals (PDF files on the CD-ROM). Basic operations are explained in the booklets. For detailed instructions on all functions and operations, see the detailed version manuals on the CD-ROM. Camera Basic Wi-Fi Function Instruction Manual...
Page 6: Quick Start Guide
Quick Start Guide Insert the battery (p.26) To charge the battery, see page 24. Insert a card (p.27) With the card’s label facing toward the back of the camera, insert it into the card slot. Attach the lens (p.36) White index Red index Align the lens’...
Page 7 Quick Start Guide Flip out the LCD monitor (p.30) When the LCD monitor displays the date/time/zone setting screens, see page 33. Focus the subject (p.41) Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway. The camera will focus the subject.
Page 8: Conventions Used In This Manual
Conventions Used in this Manual Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <9> <V> : Indicates the Multi-controller and the push direction. <0> : Indicates the Setting button. 0, 9, 7, 8 : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec.
Page 9: Table Of Contents
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures. Introduction Getting Started Basic Shooting Setting the AF and Drive Modes Image Settings Advanced Operations Shooting with the LCD Monitor (Live View Shooting) Shooting Movies Image Playback Viewing the CD-ROM Instruction Manuals /...
Page 10 Contents Introduction Compatible Cards................3 Item Check List................. 4 Instruction Manual and CD-ROMs ........... 5 Quick Start Guide ................6 Conventions Used in this Manual ............. 8 Chapters................... 9 Handling Precautions ..............14 Nomenclature ................. 16 Getting Started Charging the Battery ..............24 Installing and Removing the Battery..........
Page 11 Contents Basic Shooting A Fully Automatic Shooting (Scene Intelligent Auto) ....66 A Full Auto Techniques (Scene Intelligent Auto) ......69 7 Disabling Flash ................. 71 C Creative Auto Shooting............. 72 8: Special Scene Mode ............. 75 2 Shooting Portraits ..............76 3 Shooting Landscapes ...............
Page 12 Contents Image Settings Setting the Image-Recording Quality ..........98 i: Setting the ISO Speed ............100 A Selecting a Picture Style ............101 Setting the White Balance ............102 Auto Correction of Brightness and Contrast ......... 103 Setting Noise Reduction............... 104 Highlight Tone Priority ..............
Page 13 Contents Shooting Movies k Shooting Movies ..............134 Setting the Movie Recording Size..........137 Image Playback x Image Playback ..............140 H Searching for Images Quickly ..........141 u/y Magnified View ..............142 d Playing Back with the Touch Screen ........143 k Playing Movies................
Page 14: Handling Precautions
This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth.
Page 15 If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your Canon dealer or check the camera yourself and make sure it is working properly.
Page 16: Nomenclature
Nomenclature LCD panel (p.18) <R> Drive mode selection button (p.95) <f> AF mode selection button (p.88) ISO speed setting button (p.100) EF lens mount index (p.36) <q> Metering mode Built-in flash/AF-assist beam selection button (p.117) AF area Flash sync contacts selection mode button Hot shoe (p.92)
Page 17 Nomenclature <V> Focal plane mark AF start button (p.41, 88) <A/k> Live View shooting/ Movie shooting switch (p.119/133) <0> Start/Stop button (p.120, 134) <A> AE lock/FE lock button/ <y> Index/Reduce button Dioptric adjustment knob (p.116/141, 142) Eyecup <S> AF point selection/ Viewfinder eyepiece ...
Page 18: Lcd Panel
Nomenclature LCD panel <A> Highlight tone priority (p.106) Drive mode (p.95) Single shooting <g> ISO speed (p.100) High-speed continuous shooting i Low-speed continuous shooting ISO speed (p.100) Silent single shooting Silent continuous shooting Possible shots Self-timer: 10 sec /remote control Self-timer countdown Self-timer: 2 sec./remote control Bulb exposure time...
Page 19: Viewfinder Information
Nomenclature Viewfinder Information Spot metering circle Zone AF (Manual zone selection) (p.91) Single-point AF (Manual selection) 19-point automatic selection AF (p 91) (p 91) Zone AF points (p.91) AF points (p.91) Focusing screen Grid (p 58) Warning symbol Electronic level (p 60) <g>...
Page 20 Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). Creative Zone These modes give you more control for shooting various subjects. d : Program AE (p.110) s : Shutter-priority AE (p.111) f : Aperture-priority AE (p.112) a : Manual exposure (p.113) F : Bulb...
Page 21 Nomenclature Lens Lens without a distance scale Focusing ring (p.94, 130) Focus mode switch (p.36) Hood mount (p.38) Zoom position index Filter thread (front of lens) Zoom ring (p 37) Image Stabilizer switch (p 39) Contacts (p.15) Lens mount index (p.36)
Page 22 Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.24). Power plug Battery pack slot Charge Lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed.
Page 23: Getting Started
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration.
Page 24: Charging The Battery
Charging the Battery Remove the protective cover. Detach the protective cover provided with the battery. Attach the battery. As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. Recharge the battery.
Page 25 Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet.
Page 26: Installing And Removing The Battery
Installing and Removing the Battery Load a fully charged Battery Pack LP-E6 into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery Open the cover. Slide the lever as shown by the arrows and open the cover.
Page 27 Installing and Removing the Card The camera can use an SD, SDHC, or SDXC memory card (sold separately). An UHS-I Speed Class SDHC or SDXC memory card can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing/erasing.
Page 28: Installing And Removing The Card
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent you from forgetting to insert a card. Removing the Card Open the cover.
Page 29: Card Slot
Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to or read by the card, being erased, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking.
Page 30: Using The Lcd Monitor
Using the LCD Monitor After you flip out the LCD monitor, you can set menu functions, use Live View shooting, shoot movies, and play back images and movies. You can change the direction and angle of the LCD monitor. Flip out the LCD monitor. Rotate the LCD monitor.
Page 31: Turning On The Power
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 33 to set the date/time/zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera.
Page 32: Checking The Battery Level
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Display Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 9 - 1...
Page 33: Setting The Date, Time, And Zone
Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the date/time/zone setting screen will appear. Follow the steps below to set the time zone first. If you set the camera to the correct time zone for where you currently live, when you travel to another time zone you can simply set the camera to the correct time zone for your destination to update the camera’s date/time...
Page 34: Set The Date And Time
3 Setting the Date, Time, and Zone Set the date and time. Press the key to select the number. Press <0> so <r> is displayed. Press the <V> key to set the number, then press <0>. (Returns to <s>.) Set the daylight saving time.
Page 35: Selecting The Interface Language
Selecting the Interface Language Display the menu screen. Press the <M> button to display the menu screen. Under the [52] tab, select [LanguageK]. Press the key to select the [52] tab. Press the <V> key to select [Language ], then press <0>. Set the desired language.
Page 36: Attaching And Detaching A Lens
Attaching and Detaching a Lens The camera is compatible with all Canon EF and EF-S lenses. The camera cannot be used with EF-M lenses. Attaching a Lens Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows.
Page 37: Detaching The Lens
Attaching and Detaching a Lens Zooming Turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrows.
Page 38 Attaching and Detaching a Lens Image Conversion Factor Image sensor size (Approx.) Since the image sensor size is (22 5 x 15.0 mm / 0.88 x 0 59 in.) smaller than the 35mm film format, it will look like the lens 35mm image size focal length is increased by (36 x 24 mm / 1.42 x 0.94 in.)
Page 39: Lens Image Stabilizer
Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF-S18-135mm f/3.5-5.6 IS STM lens as an example. * IS stands for Image Stabilizer. Set the IS switch to <1>.
Page 40: Basic Operation
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup. If the camera dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (sold separately) is recommended.
Page 41: Shutter Button
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0).
Page 42 Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Main Dial After pressing a button, turn the <6> dial. When you press a button such as <f> <R> <q>, the respective function remains selected for the duration of the timer (9).
Page 43 Basic Operation Quick Control Dial After pressing a button, turn the <5> dial. When you press a button such as <f> <R> <q>, the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5> dial to set the desired setting.
Page 44 Basic Operation Multi-controller The Multi-controller <9> has eight keys that tilt in the directions shown by the arrows. Use the eight keys to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, etc.
Page 45: Lcd Panel Illumination
Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed.
Page 46: Q Quick Control For Shooting Functions
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control. Press the <Q> button. The Quick Control screen will appear. Set the desired functions. Press the <V> keys to select a function.
Page 47 Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen Aperture (p.112) Flash exposure compensation Shutter speed (p.111) AE lock* (p.116) Shooting mode* (p 20) Highlight tone priority* (p.106) Exposure ISO speed (p.100) compensation/ AEB setting Wi-Fi function* (p.114/115) Picture Style (p.101) Custom Controls...
Page 48: Menu Operations
Menu Operations You can set various settings with the menus such as the image- recording quality, date/time, etc. While looking at the LCD monitor, use the <M> button, <V> keys, and < > button on the camera back. <M> button <0>...
Page 49 3 Menu Operations Menu Setting Procedure Display the menu screen. Press the <M> button to display the menu screen. Select a tab. Press the key to select a menu tab. For example, in this manual, “the [z4] tab” refers to the screen displayed when the forth z (Shooting) tab from the left [ ] is selected.
Page 50: D Using The Touch Screen
d Using the Touch Screen The LCD monitor is a touch-sensitive panel that you can operate with your fingers. Quick Control (Sample display) Use your finger to tap (touch briefly and then remove your finger from) the LCD monitor. By tapping, you can select menus, icons, etc., displayed on the LCD monitor.
Page 51: Using The Touch Screen
d Using the Touch Screen Drag Menu screen (Sample display) Slide your finger while touching the LCD monitor. Scale display (Sample display) Operations possible by dragging your finger on the screen Selecting a menu tab or item after pressing the <M> button Setting a scale control Quick Control Setting functions during Live View shooting...
Page 52 d Using the Touch Screen 3 Touch Control Settings Select [Touch control]. Under the [53] tab, select [Touch control], then press <0>. Set the touch control setting. Select the desired setting, then press <0>. [Standard] is the normal setting. [Sensitive] provides a better touch response than [Standard].
Page 53: Before You Start
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep.
Page 54 Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed. Low-level Formatting Perform low-level formatting if the card’s recording or reading speed seems slow or if you want to erase all data on the card.
Page 55 Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved, during self-timer operation, and during touch screen operations. Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. Select [Disable]. Select [Disable], then press <0>. The beeper will not sound for any operation.
Page 56 Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor immediately after capture. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. Select [Image review].
Page 57 Before You Start 3 Reverting the Camera to the Default SettingsN The camera’s shooting function settings and menu settings can be reverted to their defaults. Select [Clear all camera settings]. Under the [54] tab, select [Clear all camera settings], then press <0>. Select [OK].
Page 58: Displaying The Grid
Displaying the Grid You can display a grid in the viewfinder to help you straighten or compose the shot. Select [VF grid display]. Under the [z1] tab, select [VF grid display], then press <0>. Select [Enable]. Select [Enable], then press <0>. When you exit the menu, the grid will appear in the viewfinder.
Page 59 Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help correct camera tilt. Note that you can check only the horizontal tilt and not the forward/backward tilt. Displaying the Electronic Level on the LCD Monitor Press the ...
Page 60 Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder During Shooting A simple electronic level using a camera icon can be displayed in the viewfinder at the center bottom. Since this can be displayed while you shoot, you can correct any tilt during handheld shooting.
Page 61: Q Displaying The Electronic Level
Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder Before ShootingN The viewfinder can display an electronic level and grid using the AF points. This is convenient to correct any camera tilt before shooting with a tripod. Select Custom Functions III.
Page 62 Q Displaying the Electronic Level Display the electronic level. Press the Depth-of-field preview button. The viewfinder will display an electronic level and grid using the AF points. 1° 6° Over...
Page 63: Feature Guide And Help
Feature Guide and Help The Feature guide and Help display information about camera features. Feature Guide The Feature guide appears when you change the shooting mode or set a shooting function, Live View shooting, movie shooting, or Quick Control for playback, and displays a brief description of that mode, function or option.
Page 64 Feature Guide and Help Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge.
Page 65: Basic Shooting
Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. With Basic Zone modes, all you do is point and shoot while the camera sets everything automatically (p.85). Also, to prevent botched pictures due to mistaken operations, advanced shooting function settings cannot be changed.
Page 66 A Fully Automatic Shooting (Scene Intelligent Auto) <A> is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.69). Set the Mode Dial to <A>. Turn the Mode Dial while holding down the lock release button at the center.
Page 67: A Fully Automatic Shooting (Scene Intelligent Auto)
A Fully Automatic Shooting (Scene Intelligent Auto) Take the picture. Press the shutter button completely to take the picture. The captured image will be displayed for 2 sec. on the LCD monitor. After you finish shooting, push down the built-in flash with your fingers. The <A>...
Page 68 A Fully Automatic Shooting (Scene Intelligent Auto) The flash fired even though it was daylight. For a backlit subject, the flash may fire to help lighten the subject’s dark areas. If you do not want the flash to fire, use the Quick Control to set [Flash firing] to [b] (p.84) or set the <7>...
Page 69: A Full Auto Techniques (Scene Intelligent Auto)
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the <A> mode, while you press the shutter button halfway to focus a still subject, the focus will be locked.
Page 70: A Live View Shooting
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 119. Set the Live View shooting/Movie shooting switch to <A>. Display the Live View image on the LCD monitor.
Page 71: Disabling Flash
7 Disabling Flash <7> is a fully-automatic shooting mode that does not use flash. It is useful in museums, aquariums, and other places where flash is prohibited. This mode is also effective for capturing the particular ambience of a scene, such as candlelight scenes. Shooting Tips Prevent camera shake if the numeric display in the viewfinder blinks.
Page 72: C Creative Auto Shooting
C Creative Auto Shooting In the <C> mode, you can easily blur the background and change the drive mode and flash firing. You can also choose the ambience you want to convey in your images. The default settings are the same as the <A>...
Page 73 C Creative Auto Shooting Shutter speed Aperture ISO speed Battery check Possible shots Image-recording quality Pressing the <Q> button enables you to set the following: (1) Ambience-based shots You can choose the ambience you want to convey in your images. Turn the <6>...
Page 74 C Creative Auto Shooting (3) Drive mode: Turn the <6> or <5> dial to select the desired drive mode. You can also select it from a list by pressing <0>. Single shooting: Shoot one image at a time. <o> High-speed continuous shooting: While you hold down the shutter button completely, shots will be taken continuously.
Page 75: 8: Special Scene Mode
8: Special Scene Mode The camera will automatically choose the appropriate settings when you select a shooting mode for your subject or scene. Set the Mode Dial to <8>. Press the <Q> button. The Quick Control screen will appear. Select a shooting mode. Press the <V>...
Page 76: Shooting Portraits
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and hair look softer. Shooting Tips The further the distance between the subject and background, the better. The further the distance between the subject and background, the more blurred the background will look.
Page 77: Shooting Landscapes
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end.
Page 78: Shooting Close-Ups
4 Shooting Close-ups When you want to shoot flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips Use a simple background. A simple background makes small objects such as flowers stand out better.
Page 79: Shooting Moving Subjects
5 Shooting Moving Subjects Use the <5> (Sports) mode to shoot a moving subject, such as a running child or a moving vehicle. Shooting Tips Use a telephoto lens. The use of a telephoto lens is recommended for shooting from a distance.
Page 80: Shooting Night Portraits (With A Tripod)
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Using a tripod is recommended. Shooting Tips Use a wide-angle lens and a tripod. When using a zoom lens, use the wide-angle end to obtain a wide night view.
Page 81: F Shooting Night Scenes (Handheld)
F Shooting Night Scenes (Handheld) Using a tripod for shooting a night scene yields the best results. However, with the <F> (Handheld Night Scene) mode, you can shoot night scenes while handholding the camera. In this mode, four shots are taken continuously for each picture, and a resulting bright image with reduced camera shake is recorded.
Page 82: G Shooting Backlit Scenes
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the <G> (HDR Backlight Control) mode. When you take one picture in this mode, three continuous shots are taken at different exposures. This results in one image, with a wide tonal range, that has minimized the blocked-up shadows caused by backlighting.
Page 83 Cautions for <6> Night Portrait and <F> Handheld Night Scene During Live View shoo ing, it may be difficult to focus dots of light such as in a night scene. In such a case, set he lens’ focus mode switch to <MF> and focus manually.
Page 84: Q Quick Control
Q Quick Control Cautions for <G> HDR Backlight Control Note that the image may not be rendered with a smooth gradation and may look irregular or have significant noise. HDR Backlight Control may not be effective for excessively backlit scenes or extremely high-contrast scenes. Q Quick Control In Basic Zone modes when the shooting function settings screen is displayed, you can press the <Q>...
Page 85 Q Quick Control Settable Functions in Basic Zone Modes : Default setting k: User selectable : Not selectable Function u: Single shooting o: High-speed continuous shooting i: Low-speed continuous shoo ing Drive B: Silent single shooting mode M: Silent continuous shooting Self-timer (p.96) a: Automatic firing Flash...
Page 86 MEMO...
Page 87: Setting The Af And Drive Modes
Setting the AF and Drive Modes The 19 AF points in the viewfinder make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF operation and drive mode that best match the shooting conditions and subject. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
Page 88: F: Selecting The Af Operation
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. Set the lens focus mode switch to <AF>.
Page 89 f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus confirmation light <o>...
Page 90 f: Selecting the AF OperationN AI Focus AF for Switching the AF Operation Automatically AI Focus AF switches the AF operation from One-Shot AF to AI Servo AF automatically if a still subject starts moving. After the subject is focused in One-Shot AF, if the subject starts moving, the camera will detect the movement, change the AF operation automatically to AI Servo AF, and keep tracking the moving subject.
Page 91: S Selecting The Af Area
S Selecting the AF AreaN 19 AF points are provided for AF. You can select the AF point(s) suiting the scene or subject. AF Area Selection Mode You can select one of three AF area selection modes. See the next page for the selection procedure.
Page 92 S Selecting the AF AreaN Selecting the AF Area Selection Mode Press the <S> or button. Look through the viewfinder and press the <S> or button. Press the button. Each time you press the button, the AF area selection mode changes.
Page 93 S Selecting the AF AreaN Selecting the AF Point Manually You can manually select the AF point or zone. If 19-point automatic selection AF + AI Servo AF has been set, you can select any position where AI Servo AF is to start. Press the <S>...
Page 94: Mf: Manual Focus
MF: Manual Focus Set the lens focus mode switch to <MF>. <4 L> will be displayed on the LCD panel. Focus the subject. Focusing ring Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder.
Page 95: Selecting The Drive Mode
i Selecting the Drive Mode Single and continuous drive modes are provided. Press the <R> button. Select the drive mode. While looking at the LCD panel, turn the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken.
Page 96: Using The Self-Timer
j Using the Self-timer Use the self-timer when you want to be in the picture. Press the <R> button. Select the self-timer. While looking at the LCD panel, turn the <6> or <5> dial to select the self-timer delay. Q : 10-sec. self-timer k : 2-sec.
Page 97: Image Settings
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
Page 98: Setting The Image-Recording Quality
Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, Select [Image quality]. Under the [z1] tab, select [Image quality], then press <0>.
Page 99 ISO speed, Picture Style, Custom Functions, and other settings. The maximum burst applies to <o> high-speed continuous shooting. Figures in parentheses apply to an UHS-I class 8 GB card based on Canon’s testing standards.
Page 100: I: Setting The Iso Speed
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically. Press the button. Set the ISO speed. While looking at the LCD panel or the viewfinder, turn the <6>...
Page 101: A Selecting A Picture Style
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, <D> (Auto) is set automatically. Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>.
Page 102: Setting The White Balance
Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the <Q> (Auto) setting will obtain the correct white balance. If natural- looking colors cannot be obtained with <Q>, you can select the white balance to match the light source or set it manually by shooting a white object.
Page 103: Auto Correction Of Brightness And Contrast
Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically.
Page 104: Setting Noise Reduction
Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced.
Page 105 3 Setting Noise ReductionN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. Select [Long exp. noise reduction]. Under the [z4] tab, select [Long exp. noise reduction], then press <0>. Set the desired setting. Select the desired setting, then press <0>.
Page 106: Highlight Tone Priority
Highlight Tone PriorityN You can minimize overexposed highlight areas. Select [Highlight tone priority]. Under the [z4] tab, select [Highlight tone priority], then press <0>. Select [Enable]. Select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights.
Page 107: Lens Peripheral Illumination / Chromatic Aberration Correction
Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. Both lens aberrations can be corrected. The default settings are [Enable] for both corrections. Peripheral Illumination Correction Select [Lens aberration correction].
Page 108 3 Lens Peripheral llumination / Chromatic Aberration Correction Chromatic Aberration Correction Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “Lens Correction Data”...
Page 109: Advanced Operations
Advanced Operations In Creative Zone modes, you can set the shutter speed and/ or aperture to set the exposure as desired. By changing the camera settings, you can obtain various results. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
Page 110: D: Program Ae
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * <d> stands for Program. * AE stands for Auto Exposure. Set the Mode Dial to <d>. Focus the subject. Look through the viewfinder and aim the AF point over the subject.
Page 111: S: Shutter-Priority Ae
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion.
Page 112: F: Aperture-Priority Ae
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus.
Page 113: A: Manual Exposure
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * <a>...
Page 114: Setting Exposure Compensation
Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3- stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
Page 115: Auto Exposure Bracketing (Aeb)
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. Select [Expo.comp./AEB].
Page 116: A Ae Lock
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the <A> button to lock the exposure, then recompose and take the shot.
Page 117: D Using The Built-In Flash
D Using the Built-in Flash In Creative Zone modes, just press the <D> button to raise the built-in flash for flash photography. To retract the built-in flash, push it back down with your fingers. In Basic Zone modes (except <7> <3> <5>...
Page 118 D Using the Built-in Flash Effective Range of Built-in Flash [Approx. in meters/feet] EF-S18-55mm f/3.5-5.6 IS STM EF-S18-135mm f/3.5-5.6 IS STM ISO Speed EF-S18-200mm f/3.5-5.6 IS Wide Angle: f/3.5 Telephoto: f/5.6 1-3.4/3.3-11.2 1-2.1/3.3-7.0 1-4.8/3.3-15.9 1-3 0/3.3-9.9 1-6.9/3.3-22.5 1-4.3/3.3-14.1 1.2-9.7/4.0-31.8 1-6.1/3.3-19.9 1600 1.7-13.7/5.6-45.0 1.1-8.6/3.5-28.1...
Page 119: Shooting With The Lcd Monitor
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to <A>. If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images.
Page 120 A Shooting with the LCD Monitor Set the Live View shooting/Movie shooting switch to <A>. Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor. The Live View image will closely reflect the brightness level of the actual image you capture.
Page 121 A Shooting with the LCD Monitor Enabling Live View Shooting Set [A1: Live View shoot.] to [Enable]. Number of Possible Shots with Live View Shooting [Approx. number of shots] Room Temperature Low Temperatures Temperature ° ° ° ° C / 73 C / 32 No Flash 50% Flash Use...
Page 122: Information Display
A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change. Possible shots AF method •c : u+Tracking Maximum burst/Number of remaining multiple exposures •o : FlexiZone - Multi Battery check •d : FlexiZone - Single AF point (FlexiZone - Single)
Page 123: Using Af To Focus (Af Method)
This can greatly affect the AF speed and the camera may take a longer time to focus (phase-difference detection generally allows faster AF focusing). For details, refer to Canon Web site. Selecting the AF Method You can select an AF method to suit the shooting conditions and your subject.
Page 124: Using Af To Focus (Af Method)
Using AF to Focus (AF Method) Select an AF point. When a face is detected, the frame will appear over the face to be focused. If multiple faces are detected, <q> will be displayed. Use <9> to move the <q> frame over the face you want to focus on.
Page 125 Using AF to Focus (AF Method) FlexiZone - Multi: o You can focus over a wide area with up to 31 AF points (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection). Display the Live View image. Press the <0>...
Page 126 Using AF to Focus (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus a particular subject. Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor.
Page 127 Using AF to Focus (AF Method) Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.88), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation.
Page 128 Using AF to Focus (AF Method) The AF point (or zone) selection will change in the direction you tilt <9>. If you press <0>, the center AF point (or center Zone) will be selected. You can also use the <6> and <5>...
Page 129: Shooting With The Touch Shutter
x Shooting with the Touch Shutter Just by tapping the LCD monitor screen, you can focus and take the picture automatically. This works in all shooting modes. Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor.
Page 130: Mf: Focusing Manually
MF: Focusing Manually You can magnify the image and focus precisely with manual focus. Set the lens focus mode switch to <MF>. Turn the lens focusing ring to focus roughly. Display the magnifying frame. Press the button. The magnifying frame will appear. You can also tap [u] on the screen to magnify the image.
Page 131 MF: Focusing Manually Focus manually. While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. Take the picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.120).
Page 132 MEMO...
Page 133: Shooting Movies
Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to <k>. The movie recording format will be MOV. For cards that can record movies, see page 3. If you handhold the camera and shoot movies, camera shake can cause blurred movies.
Page 134: K Shooting Movies
k Shooting Movies Autoexposure Shooting When the shooting mode is set to other than <a>, autoexposure control will take effect to suit the scene’s current brightness. Set the shooting mode to a mode other than <a>. Set the Live View shooting/Movie shooting switch to <k>.
Page 135 k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. Set the Mode Dial to <a>. Set the Live View shooting/Movie shooting switch to <k>.
Page 136 k Shooting Movies Information Display Each time you press the button, the information display will change. Possible shots AF method •c : u + Tracking Maximum burst •o: FlexiZone - Multi Movie shooting remaining time*/ •d : FlexiZone - Single Elapsed time Movie shooting mode Battery check...
Page 137: Setting The Movie Recording Size
Setting the Movie Recording Size With [Z2: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image Size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9.
Page 138 3 Setting the Movie Recording Size Total Movie Recording Time and File Size Per Minute Total Recording Time (approx.) Movie Recording File Size Size (approx.) 4 GB Card 8 GB Card 16 GB Card 654 X 16 min. 32 min. 1 hr.
Page 139: Image Playback
Image Playback This chapter explains basic procedures to play back images and movies. Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
Page 140: X Image Playback
x Image Playback Single-Image Display Play back the image. Press the <x> button. The last captured image or last image played back will appear. Select an image. To play back images starting with the last image, turn the <5> dial counterclockwise.
Page 141: H Searching For Images Quickly
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing four or nine images on one screen. Switch to the index display. During image playback, press the ...
Page 142: U/Y Magnified View
u/y Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. Magnify the image. Press the button during image playback. The image will be magnified. If you hold down the button, the image will be magnified until it reaches the maximum magnification.
Page 143: Playing Back With The Touch Screen
d Playing Back with the Touch Screen The LCD monitor is a touch-sensitive panel that you can touch with your fingers for various playback operations. First, press the <x> button to play back images. Browsing Images Swipe with one finger. With single-image display, touch the LCD monitor with one finger.
Page 144 d Playing Back with the Touch Screen Reducing Image (Index Display) Pinch two fingers. Touch the screen with two fingers spread apart, then pinch your fingers together on the screen. Each time you pinch your fingers, the screen changes from a single-image display to a 4-image index display and 9-image index display.
Page 145: Playing Movies
k Playing Movies Play back the image. Press the <x> button to display an image. Select a movie. Turn the <5> dial to select the movie to be played. In the single-image display, the <s1> icon displayed on the upper left of the screen indicates a movie.
Page 146 k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. Adjust the slow motion speed by pressing the key. 8 Slow motion The slow mo ion speed is indicated at the upper right of the screen.
Page 147: L Erasing Images
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them.
Page 148 MEMO...
Page 149: Viewing The Cd-Rom Instruction Manuals
Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer This chapter explains how to install the Camera Instruction Manual CD-ROM to your computer, download images from the camera to your computer, gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on your computer.
Page 150: Viewing The Camera Instruction Manual Cd-Rom
Viewing the Camera Instruction Manual CD-ROM The Camera Instruction Manual CD-ROM contains the following electronic manuals (PDF): Camera Instruction Manual Explains all the camera functions and procedures, including basic content. Wi-Fi Function Instruction Manual Explains all the Wi-Fi functions and procedures, including basic content.
Page 151: Select The Language
Select the language. EOS 70D (W) / EOS 70D (N) Français English Español © CANON NC 20 3 Click on the manual you want to view. EOS 70D W) / EOS 70D (N) Camera Instruction Manual Wi Fi Function Instruction Manual...
Page 152: Downloading Images To A Computer
Downloading Images to a Computer You can use the provided software to download the images in the camera to your computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer Install the software (p.156) Use the provided interface cable to connect the camera to your computer.
Page 153 Use ImageBrowser EX. For details, refer to the Software Instruction Manual on the CD-ROM (p.157). When downloading images from the camera to your computer, with a card reader without using Canon software, copy the DCIM folder on the card to your computer.
Page 154: Software Overview
Software Overview EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely with the computer connected to the camera.
Page 155 Software Overview Picture Style Editor You can edit Picture Styles and create and save original Picture Style files. This software is aimed at advanced users who are experienced in processing images.
Page 156: Installing The Software
Insert EOS DIGITAL Solution Disk (CD-ROM). For Macintosh, double-click to open the CD-ROM icon displayed on the desktop, then double-click on [Canon EOS Digital Installer]. When a screen to select where you live or a language appears, follow the on-screen instructions.
Page 157: Software Instruction Manual
Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Software Instruction Manual PDFs Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. Copy the [English] folder to your computer.
Page 158 This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this...
Page 159 Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet.
Page 160 • Before storing the camera or accessory when not in use, remove the battery pack and disconnect the power plug. This is to prevent electrical shock, heat generation, and fire. • Do not use the equipment where there is flammable gas. This is to prevent an explosion or fire.
Page 161 • Do not use paint thinner, benzene, or other organic solvents to clean the equipment. Doing so may cause fire or a health hazard. If the product does not work properly or requires repair, contact your dealer or your nearest Canon Service Center.
Page 162 If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516)328-5600 This Class B digital apparatus complies wi h Canadian ICES-003.
Page 163 4. Do not expose the charger to rain or snow. 5. Use of an attachment not recommended or sold by Canon may result in fire, electric shock, or personal injury. 6. To reduce risk of damage to electric plug and cord, pull by plug rather than by cord when disconnecting charger.
Page 164 SOUTH AMERICA http://www.cla.canon.com ASIA CANON (China) Co., LTD. 15F Jinbao Building No.89 Jinbao Street, Dongcheng District, Beijing 100005, China CANON HONGKONG CO., LTD. 19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong CANON SINGAPORE PTE. LTD. 1 Harbour Front Avenue, #04-01 Keppel Bay Tower, Singapore 098632 CANON KOREA CONSUMER IMAGING INC. Canon BS Tower 5F, #168-12 Samseong-dong, Gangnam-gu, Seoul, Korea OCEANIA CANON AUSTRALIA PTY. LTD. 1 Thomas Holt Drive, North Ryde, Sydney N.S.W. 2113, Australia CANON NEW ZEALAND LTD. Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand CANON MARKETING JAPAN INC. JAPAN...
Page 165 EOS 70D (W) EOS 70D (N) The EOS 70D (N) does not have the Wi-Fi function explained in INSTRUCTION MANUAL this manual.
Page 166 After shooting, play images back and check whether they have been properly recorded. If the camera or memory card is faulty and the images cannot be recorded or downloaded to a computer, Canon cannot be held liable for any loss or inconvenience caused.
Page 167 Compatible Cards The camera can use the following cards regardless of capacity: • SD memory cards • SDHC memory cards* • SDXC memory cards* * UHS-I cards supported. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table.
Page 168 Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Battery Pack Battery Charger LP-E6 LC-E6/LC-E6E* Camera (with protective cover) (with body cap) Interface Cable Wide Strap EW-EOS70D * Battery Charger LC-E6 or LC-E6E is provided.
Page 169 Instruction Manual and CD-ROMs The instruction manual consists of booklets and electronic manuals (PDF files on the CD-ROM). Basic operations are explained in the booklets. For detailed instructions on all functions and operations, see the detailed version manuals on the CD-ROM. Camera Basic Wi-Fi Function Instruction Manual...
Page 170: To Charge The Battery, See
Quick Start Guide Insert the battery (p.30) To charge the battery, see page 28. Insert a card (p.31) With the card’s label facing toward the back of the camera, insert it into the card slot. Attach the lens (p.40) White index Red index Align the lens’...
Page 171 Quick Start Guide Flip out the LCD monitor (p.34) When the LCD monitor displays the date/time/zone setting screens, see page 37. Focus the subject (p.45) Look through the viewfinder and aim the viewfinder center over the subject. Press the shutter button halfway. The camera will focus the subject.
Page 172 Conventions Used in this Manual Icons in this Manual <6> : Indicates the Main Dial. <5> : Indicates the Quick Control Dial. <9> <V> : Indicates the Multi-controller and the push direction. <0> : Indicates the Setting button. 0, 9, 7, 8 : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec.
Page 173 Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures. Introduction Getting Started Basic Shooting Setting the AF and Drive Modes Image Settings Advanced Operations Flash Photography Shooting with the LCD Monitor (Live View Shooting) Shooting Movies Image Playback Post-Processing Images...
Page 174 Contents Introduction Compatible Cards................3 Item Check List................. 4 Instruction Manual and CD-ROMs ........... 5 Quick Start Guide ................6 Conventions Used in this Manual ............. 8 Chapters................... 9 Index to Features ................16 Handling Precautions ..............18 Nomenclature ................. 20 Getting Started Charging the Battery ..............
Page 175 Contents Basic Shooting A Fully Automatic Shooting (Scene Intelligent Auto) ....72 A Full Auto Techniques (Scene Intelligent Auto) ......75 7 Disabling Flash ................. 77 C Creative Auto Shooting............. 78 8: Special Scene Mode ............. 81 2 Shooting Portraits ..............82 3 Shooting Landscapes ...............
Page 176 Contents Setting the White Balance ............134 O Custom White Balance............135 P Setting the Color Temperature ..........137 White Balance Correction............. 138 Auto Correction of Brightness and Contrast ......... 140 Setting Noise Reduction............... 141 Highlight Tone Priority ..............145 Lens Peripheral Illumination / Chromatic Aberration Correction ..
Page 177 Contents Flash Photography D Using the Built-in Flash ............. 188 D Using an External Speedlite............193 Setting the Flash ................195 Using Wireless Flash ..............203 Shooting with the LCD Monitor (Live View Shooting) A Shooting with the LCD Monitor ..........216 Shooting Function Settings ............
Page 178 Contents Setting Ratings ................302 Q Quick Control for Playback ............. 304 k Enjoying Movies ..............306 k Playing Movies ............... 308 X Editing a Movie’s First and Last Scenes ......... 310 Slide Show (Auto Playback) ............312 Viewing Images on a TV Set ............316 K Protecting Images..............
Page 179 Contents Custom Function Settings............. 365 C.Fn I: Exposure ................ 365 C.Fn II: Autofocus ..............368 C.Fn III: Operation/Others ............375 8: Fine Adjustment of AF’s Point of Focus ......... 377 8: Custom Controls ..............383 Registering My Menu ..............389 w: Register Custom Shooting Modes...........
Page 180: Index To Features
Index to Features Power AF area selection mode p.103 AF point selection p.105 Charging the battery p.28 AF Microadjustment p.377 Battery check p.36 Manual focusing p.110 Battery information check p.396 Household power outlet p.400 Metering Auto power off p.59 Metering mode p.165 Card Drive...
Page 181 Index to Features Remote control p.184 Magnified view p.298 Quick Control p.50 Image rotate p.301 Rating p.302 Exposure Adjustment Movie playback p.308 Exposure compensation p.167 Slide show p.312 p.168 Viewing images on a AE lock p.170 TV set p.316 Safety shift p.367 Protect p.320...
Page 182: Camera Care
This camera is a precision instrument. Do not drop it or subject it to physical shock. The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult the nearest Canon Service Center. Wipe off any water droplets with a dry and clean cloth. If the camera has been exposed to salty air, wipe it with a well-wrung wet cloth.
Page 183 If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your Canon dealer or check the camera yourself and make sure it is working properly.
Page 184 Nomenclature LCD panel (p.22) <R> Drive mode selection button (p.111) <f> AF mode selection button (p.100) ISO speed setting button (p.120) EF lens mount index (p.40) <q> Metering mode Built-in flash/AF-assist beam selection button (p.165) (p.188/203) AF area Flash sync contacts selection mode button Hot shoe (p.193)
Page 185 Nomenclature <V> Focal plane mark AF start button (p.45, 100, 217, 259) <A/k> Live View shooting/ Movie shooting switch (p.215/251) <0> Start/Stop button (p.216, 252) <A> AE lock/FE lock button/ <y> Index/Reduce button Dioptric adjustment knob (p.44) (p.170, 192/296, 298) Eyecup (p.183) <S>...
Page 186 Nomenclature LCD panel <A> Highlight tone priority (p.145) Drive mode (p.111) Single shooting <g> ISO speed (p.120) High-speed continuous shooting i Low-speed continuous shooting ISO speed (p.120) Silent single shooting Silent continuous shooting Possible shots Self-timer: 10 sec /remote control Self-timer countdown Self-timer: 2 sec./remote control Bulb exposure time...
Page 187 Nomenclature Viewfinder Information Spot metering circle (p.165) Zone AF (Manual zone selection) (p.103) Single-point AF (Manual selection) 19-point automatic selection AF (p.103) (p.103) Zone AF points (p.103) AF points (p.103) Focusing screen Grid (p 64) Warning symbol Electronic level (p 66) (p.376) <g>...
Page 188 Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). Creative Zone These modes give you more control for shooting various subjects. d : Program AE (p.158) s : Shutter-priority AE (p.160) f : Aperture-priority AE (p.162) a : Manual exposure (p.164) F : Bu b (p.171)
Page 189 Nomenclature Lens Lens without a distance scale Focusing ring (p.110, 247) Focus mode switch (p.40) Hood mount (p.42) Zoom position index Filter thread (front of lens) Zoom ring (p.41) Image Stabilizer switch (p.43) Contacts (p.19) Lens mount index (p.40)
Page 190 Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6 (p.28). Power plug Battery pack slot Charge Lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed.
Page 191: Getting Started
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration.
Page 192: Charging The Battery
Charging the Battery Remove the protective cover. Detach the protective cover provided with the battery. Attach the battery. As shown in the illustration, attach the battery securely to the charger. To detach the battery, follow the above procedure in reverse. Recharge the battery.
Page 193 Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged. Charge the battery before use. Recharge the battery on the day before or on the day it is to be used. Even during storage, a charged battery will gradually drain and lose its capacity. After recharging the battery, detach it and disconnect the charger from the power outlet.
Page 194: Installing And Removing The Battery
Installing and Removing the Battery Load a fully charged Battery Pack LP-E6 into the camera. The camera’s viewfinder becomes bright when a battery is installed, and darkens when the battery is removed. Installing the Battery Open the cover. Slide the lever as shown by the arrows and open the cover.
Page 195: Installing And Removing The Card
Installing and Removing the Card The camera can use an SD, SDHC, or SDXC memory card (sold separately). An UHS-I Speed Class SDHC or SDXC memory card can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing/erasing.
Page 196: Insert A Card (P.
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent you from forgetting to insert a card (p.408). Removing the Card Open the cover.
Page 197 Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are being written to or read by the card, being erased, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking.
Page 198: Using The Lcd Monitor
Using the LCD Monitor After you flip out the LCD monitor, you can set menu functions, use Live View shooting, shoot movies, and play back images and movies. You can change the direction and angle of the LCD monitor. Flip out the LCD monitor. Rotate the LCD monitor.
Page 199: Turning On The Power
Turning on the Power If you turn on the power switch and the date/time/zone setting screen appears, see page 37 to set the date/time/zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera.
Page 200 Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Display Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 9 - 1...
Page 201: Setting The Date, Time, And Zone
Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the date/time/zone setting screen will appear. Follow the steps below to set the time zone first. If you set the camera to the correct time zone for where you currently live, when you travel to another time zone you can simply set the camera to the correct time zone for your destination to update the camera’s date/time...
Page 202 3 Setting the Date, Time, and Zone Set the date and time. Press the key to select the number. Press <0> so <r> is displayed. Press the <V> key to set the number, then press <0>. (Returns to <s>.) Set the daylight saving time.
Page 203: Selecting The Interface Language
Selecting the Interface Language Display the menu screen. Press the <M> button to display the menu screen. Under the [52] tab, select [LanguageK]. Press the key to select the [52] tab. Press the <V> key to select [Language ], then press <0>. Set the desired language.
Page 204: Attaching And Detaching A Lens
Attaching and Detaching a Lens The camera is compatible with all Canon EF and EF-S lenses. The camera cannot be used with EF-M lenses. Attaching a Lens Remove the caps. Remove the rear lens cap and the body cap by turning them as shown by the arrows.
Page 205 Attaching and Detaching a Lens Zooming Turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus. Detaching the Lens While pressing the lens release button, turn the lens as shown by the arrows.
Page 206 Attaching and Detaching a Lens Image Conversion Factor Image sensor size (Approx.) Since the image sensor size is (22.5 x 15.0 mm / 0.88 x 0.59 in.) smaller than the 35mm film format, it will look like the lens 35mm image size focal length is increased by (36 x 24 mm / 1.42 x 0.94 in.) approx.
Page 207: Lens Image Stabilizer
Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF-S18-135mm f/3.5-5.6 IS STM lens as an example. * IS stands for Image Stabilizer. Set the IS switch to <1>.
Page 208: Basic Operation
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the AF points in the viewfinder look sharp. If the knob is difficult to turn, remove the eyecup (p.183). If the camera dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (sold separately) is recommended.
Page 209 Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0).
Page 210 Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Main Dial After pressing a button, turn the <6> dial. When you press a button such as <f> <R> <q>, the respective function remains selected for the duration of the timer (9).
Page 211 Basic Operation Quick Control Dial After pressing a button, turn the <5> dial. When you press a button such as <f> <R> <q>, the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5> dial to set the desired setting.
Page 212 Basic Operation Multi-controller The Multi-controller <9> has eight keys that tilt in the directions shown by the arrows. Use the eight keys to select the AF point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, etc.
Page 213 Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed.
Page 214: Q Quick Control For Shooting Functions
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called Quick Control. Press the <Q> button. The Quick Control screen will appear. Set the desired functions. Press the <V> keys to select a function.
Page 215 Q Quick Control for Shooting Functions Settable Functions on Quick Control Screen Aperture (p.162) Flash exposure compensation (p.193) Shutter speed (p.160) AE lock* (p.170) Shooting mode* (p 24) Highlight tone priority* (p.145) Exposure ISO speed (p.120) compensation/ AEB setting Wi-Fi function* (p.167/168) Picture Style (p.126) Custom Controls (p.383)
Page 216: Menu Operations
Menu Operations You can set various settings with the menus such as the image- recording quality, date/time, etc. While looking at the LCD monitor, use the <M> button, <V> keys, and < > button on the camera back. <M> button <0>...
Page 217 3 Menu Operations Menu Setting Procedure Display the menu screen. Press the <M> button to display the menu screen. Select a tab. Press the key to select a menu tab. For example, in this manual, “the [z4] tab” refers to the screen displayed when the forth z (Shooting) tab from the left [ ] is selected.
Page 218 d Using the Touch Screen The LCD monitor is a touch-sensitive panel that you can operate with your fingers. Quick Control (Sample display) Use your finger to tap (touch briefly and then remove your finger from) the LCD monitor. By tapping, you can select menus, icons, etc., displayed on the LCD monitor.
Page 219 d Using the Touch Screen Drag Menu screen (Sample display) Slide your finger while touching the LCD monitor. Scale display (Sample display) Operations possible by dragging your finger on the screen Selecting a menu tab or item after pressing the <M> button Setting a scale control Quick Control Setting functions during Live View shooting...
Page 220 d Using the Touch Screen 3 Touch Control Settings Select [Touch control]. Under the [53] tab, select [Touch control], then press <0>. Set the touch control setting. Select the desired setting, then press <0>. [Standard] is the normal setting. [Sensitive] provides a better touch response than [Standard].
Page 221: Before You Start
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data on the card will be erased. Even protected images will be erased, so make sure there is nothing you need to keep.
Page 222 Before You Start Format the card in the following cases: The card is new. The card was formatted by a different camera or a computer. The card is full with images or data. A card-related error is displayed (p.432). Low-level Formatting Perform low-level formatting if the card’s recording or reading speed seems slow or if you want to erase all data on the card.
Page 223: Disabling The Beeper
Before You Start 3 Disabling the Beeper You can prevent the beeper from sounding when focus is achieved, during self-timer operation, and during touch screen operations. Select [Beep]. Under the [z1] tab, select [Beep], then press <0>. Select [Disable]. Select [Disable], then press <0>. The beeper will not sound for any operation.
Page 224: Setting The Image Review Time
Before You Start 3 Setting the Image Review Time You can set how long the image is displayed on the LCD monitor immediately after capture. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. Select [Image review].
Page 225 Before You Start 3 Reverting the Camera to the Default SettingsN The camera’s shooting function settings and menu settings can be reverted to their defaults. Select [Clear all camera settings]. Under the [54] tab, select [Clear all camera settings], then press <0>. Select [OK].
Page 226 Before You Start Image-recording Settings Camera Settings Image quality Auto power off 1 min. Picture Style Auto Beep Enable Auto Lighting Release shutter Standard Enable Optimizer without card Image review 2 sec. Peripheral Enable/ illumination Correction data Highlight alert Disable correction retained AF point display...
Page 227 Before You Start Live View Shooting Settings Movie Shooting Settings u+Tracking AF method Live View Enable shooting Movie Servo AF Enable u+Tracking AF method Silent LV Mode 1 shooting Continuous AF Enable Touch shutter Disable Metering timer 16 sec. Grid display Grid display Aspect ratio Movie...
Page 228: Displaying The Grid
Displaying the Grid You can display a grid in the viewfinder to help you straighten or compose the shot. Select [VF grid display]. Under the [z1] tab, select [VF grid display], then press <0>. Select [Enable]. Select [Enable], then press <0>. When you exit the menu, the grid will appear in the viewfinder.
Page 229: Q Displaying The Electronic Level
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor and in the viewfinder to help correct camera tilt. Note that you can check only the horizontal tilt and not the forward/backward tilt. Displaying the Electronic Level on the LCD Monitor Press the ...
Page 230 Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder During Shooting A simple electronic level using a camera icon can be displayed in the viewfinder at the center bottom. Since this can be displayed while you shoot, you can correct any tilt during handheld shooting.
Page 231 Q Displaying the Electronic Level 3 Displaying the Electronic Level in the Viewfinder Before ShootingN The viewfinder can display an electronic level and grid using the AF points. This is convenient to correct any camera tilt before shooting with a tripod. Select Custom Functions III.
Page 232 Q Displaying the Electronic Level Display the electronic level. Press the Depth-of-field preview button. The viewfinder will display an electronic level and grid using the AF points. 1° 6° Over Even when the tilt is corrected, there may be a margin of error of ±1°. If he camera is very tilted, the electronic level’s margin of error will be larger.
Page 233: Feature Guide And Help
Feature Guide and Help The Feature guide and Help display information about camera features. Feature Guide The Feature guide appears when you change the shooting mode or set a shooting function, Live View shooting, movie shooting, or Quick Control for playback, and displays a brief description of that mode, function or option.
Page 234 Feature Guide and Help Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge.
Page 235: Basic Shooting
Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. With Basic Zone modes, all you do is point and shoot while the camera sets everything automatically (p.91, 404). Also, to prevent botched pictures due to mistaken operations, advanced shooting function settings cannot be changed.
Page 236: A Fully Automatic Shooting (Scene Intelligent Auto)
A Fully Automatic Shooting (Scene Intelligent Auto) <A> is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.75). Set the Mode Dial to <A>. Turn the Mode Dial while holding down the lock release button at the center.
Page 237 A Fully Automatic Shooting (Scene Intelligent Auto) Take the picture. Press the shutter button completely to take the picture. The captured image will be displayed for 2 sec. on the LCD monitor. After you finish shooting, push down the built-in flash with your fingers. The <A>...
Page 238 A Fully Automatic Shooting (Scene Intelligent Auto) The flash fired even though it was daylight. For a backlit subject, the flash may fire to help lighten the subject’s dark areas. If you do not want the flash to fire, use the Quick Control to set [Flash firing] to [b] (p.90) or set the <7>...
Page 239: A Full Auto Techniques (Scene Intelligent Auto)
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the <A> mode, while you press the shutter button halfway to focus a still subject, the focus will be locked.
Page 240 A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 215. Set the Live View shooting/Movie shooting switch to <A>. Display the Live View image on the LCD monitor.
Page 241: Disabling Flash
7 Disabling Flash <7> is a fully-automatic shooting mode that does not use flash. It is useful in museums, aquariums, and other places where flash is prohibited. This mode is also effective for capturing the particular ambience of a scene, such as candlelight scenes. Shooting Tips Prevent camera shake if the numeric display in the viewfinder blinks.
Page 242: C Creative Auto Shooting
C Creative Auto Shooting In the <C> mode, you can easily blur the background and change the drive mode and flash firing. You can also choose the ambience you want to convey in your images. The default settings are the same as the <A>...
Page 243 C Creative Auto Shooting Shutter speed Aperture ISO speed Battery check Possible shots Image-recording quality Pressing the <Q> button enables you to set the following: (1) Ambience-based shots You can choose the ambience you want to convey in your images. Turn the <6>...
Page 244 C Creative Auto Shooting (3) Drive mode: Turn the <6> or <5> dial to select the desired drive mode. You can also select it from a list by pressing <0>. Single shooting: Shoot one image at a time. <o> High-speed continuous shooting: While you hold down the shutter button completely, shots will be taken continuously.
Page 245: 8: Special Scene Mode
8: Special Scene Mode The camera will automatically choose the appropriate settings when you select a shooting mode for your subject or scene. Set the Mode Dial to <8>. Press the <Q> button. The Quick Control screen will appear. Select a shooting mode. Press the <V>...
Page 246: Shooting Portraits
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and hair look softer. Shooting Tips The further the distance between the subject and background, the better. The further the distance between the subject and background, the more blurred the background will look.
Page 247: Shooting Landscapes
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips With a zoom lens, use the wide-angle end. When using the wide-angle end of a zoom lens, objects near and far will be in focus better than at the telephoto end.
Page 248: Shooting Close-Ups
4 Shooting Close-ups When you want to shoot flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips Use a simple background. A simple background makes small objects such as flowers stand out better.
Page 249: Shooting Moving Subjects
5 Shooting Moving Subjects Use the <5> (Sports) mode to shoot a moving subject, such as a running child or a moving vehicle. Shooting Tips Use a telephoto lens. The use of a telephoto lens is recommended for shooting from a distance.
Page 250: Shooting Night Portraits (With A Tripod)
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Using a tripod is recommended. Shooting Tips Use a wide-angle lens and a tripod. When using a zoom lens, use the wide-angle end to obtain a wide night view.
Page 251: F Shooting Night Scenes (Handheld)
F Shooting Night Scenes (Handheld) Using a tripod for shooting a night scene yields the best results. However, with the <F> (Handheld Night Scene) mode, you can shoot night scenes while handholding the camera. In this mode, four shots are taken continuously for each picture, and a resulting bright image with reduced camera shake is recorded.
Page 252: G Shooting Backlit Scenes
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the <G> (HDR Backlight Control) mode. When you take one picture in this mode, three continuous shots are taken at different exposures. This results in one image, with a wide tonal range, that has minimized the blocked-up shadows caused by backlighting.
Page 253 Cautions for <6> Night Portrait and <F> Handheld Night Scene During Live View shoo ing, it may be difficult to focus dots of light such as in a night scene. In such a case, set he lens’ focus mode switch to <MF> and focus manually.
Page 254: Q Quick Control
Q Quick Control Cautions for <G> HDR Backlight Control Note that the image may not be rendered with a smooth gradation and may look irregular or have significant noise. HDR Backlight Control may not be effective for excessively backlit scenes or extremely high-contrast scenes. Q Quick Control In Basic Zone modes when the shooting function settings screen is displayed, you can press the <Q>...
Page 255 Q Quick Control Settable Functions in Basic Zone Modes : Default setting k: User selectable : Not selectable Function u: Single shooting o: High-speed continuous shooting i: Low-speed continuous shoo ing Drive B: Silent single shooting mode M: Silent continuous shooting Self-timer (p.113) a: Automatic firing Flash...
Page 256: Shoot By Ambience Selection
Shoot by Ambience Selection Except in the <A>, <7>, and <G> Basic Zone modes, you can select the ambience for shooting. Ambience Ambience Effect 2 3 4 5 6 F k k k k k k k No setting Standard setting k k k k k k k Low / Standard / Strong Vivid k k k k k k k Low / Standard / Strong...
Page 257 Shoot by Ambience Selection The LCD monitor will display how the image will look with the selected ambience. Set the ambience effect. Press the <V> key to select the effect bar so that [Effect] appears at the bottom. Press the key to select the desired effect.
Page 258 Shoot by Ambience Selection Ambience Settings Standard setting Standard image characteristics for the respective shooting mode. Note that <2> has image characteristics geared for portraits and <3> is geared for landscapes. Each ambience is a modification of the respective shooting mode’s image characteristics. Vivid The subject will look sharp and vivid.
Page 259 Shoot by Ambience Selection Brighter The picture will look brighter. Darker The picture will look darker. Monochrome The picture will be monochrome. You can select the monochrome color to be black and white, sepia, or blue. When [Monochrome] is selected, <z> will appear in the viewfinder.
Page 260: Shoot By Lighting Or Scene Type
Shoot by Lighting or Scene Type In the <2>, <3>, <4>, and <5> Basic Zone modes, you can shoot while the settings match the lighting or scene type. Normally, [ Default setting] is adequate, but if the settings match the lighting condition or scene, the picture will look more accurate to your eye.
Page 261 Shoot by Lighting or Scene Type On the Quick Control screen, select the lighting or scene type. Press the <Q> button (7). Press the <V> key to select Default setting]. [Light/scene- based shots] will appear on the screen. Press the key to select the desired lighting or scene type.
Page 262 Shoot by Lighting or Scene Type Lighting or Scene Type Settings Default setting Default setting suited for most subjects. Daylight For subjects under sunlight. Gives more natural-looking blue skies and greenery and reproduces light-colored flowers better. Shade For subjects in the shade. Suitable for skin tones, which may look too bluish, and for light-colored flowers.
Page 263: Setting The Af And Drive Modes
Setting the AF and Drive Modes The 19 AF points in the viewfinder make AF shooting suitable for a wide variety of subjects and scenes. You can also select the AF operation and drive mode that best match the shooting conditions and subject. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
Page 264 f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. Set the lens focus mode switch to <AF>.
Page 265: Ai Servo Af For Moving Subjects
f: Selecting the AF OperationN One-Shot AF for Still Subjects Suited for still subjects. When you press the shutter button halfway, the camera will focus only once. When focus is achieved, the AF point that achieved focus will be displayed, and the focus confirmation light <o>...
Page 266 f: Selecting the AF OperationN AI Focus AF for Switching the AF Operation Automatically AI Focus AF switches the AF operation from One-Shot AF to AI Servo AF automatically if a still subject starts moving. After the subject is focused in One-Shot AF, if the subject starts moving, the camera will detect the movement, change the AF operation automatically to AI Servo AF, and keep tracking the moving subject.
Page 267 S Selecting the AF AreaN 19 AF points are provided for AF. You can select the AF point(s) suiting the scene or subject. AF Area Selection Mode You can select one of three AF area selection modes. See the next page for the selection procedure.
Page 268 S Selecting the AF AreaN Selecting the AF Area Selection Mode Press the <S> or button. Look through the viewfinder and press the <S> or button. Press the button. Each time you press the button, the AF area selection mode changes.
Page 269 S Selecting the AF AreaN Selecting the AF Point Manually You can manually select the AF point or zone. If 19-point automatic selection AF + AI Servo AF has been set, you can select any position where AI Servo AF is to start. Press the <S>...
Page 270: Af Area Selection Modes
AF Area Selection Modes Single-point AF (Manual Selection) Select one AF point <S> to be used for focusing. Zone AF (Manual Zone Selection) The 19 AF points are divided into five zones for focusing. All the AF points in the selected zone are used for the automatic selection of the point of focus.
Page 271 AF Area Selection Modes 19-point Automatic Selection AF All the AF points are used to focus. This mode is set automatically in Basic Zone modes. With One-Shot AF, pressing the shutter button halfway will display the AF point(s) <S> that achieved focus.
Page 272 AF Area Selection Modes AF Operation and Maximum Lens Apertures Maximum Lens Aperture: f/3.2 - f/5.6 With all AF points, cross-type AF sensitive to both vertical and horizontal lines is possible. However, with the lenses below, the peripheral AF points will detect only vertical or horizontal lines (no cross-type focusing).
Page 273: When Autofocus Fails
When Autofocus Fails Autofocus can fail to achieve focus (viewfinder’s focus confirmation light <o> blinks) with certain subjects such as the following: Subjects Difficult to Focus Very low-contrast subjects (Example: Blue sky, solid-color walls, etc.) Subjects in very low light Extremely backlit and reflective subjects (Example: Car with a highly reflective body, etc.) Near and far subjects covered by an AF point...
Page 274: Mf: Manual Focus
When Autofocus Fails MF: Manual Focus Set the lens focus mode switch to <MF>. <4 L> will be displayed on the LCD panel. Focus the subject. Focusing ring Focus by turning the lens focusing ring until the subject looks sharp in the viewfinder.
Page 275: Selecting The Drive Mode
i Selecting the Drive Mode Single and continuous drive modes are provided. Press the <R> button. Select the drive mode. While looking at the LCD panel, turn the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken.
Page 276 i Selecting the Drive Mode If or <M> is set, the time lag from when you press the shutter button completely until the picture is shot will be slightly longer than with normal single or continuous shooting. When the battery level is low, the continuous shooting speed may become slightly slower.
Page 277: Using The Self-Timer
j Using the Self-timer Use the self-timer when you want to be in the picture. Press the <R> button. Select the self-timer. While looking at the LCD panel, turn the <6> or <5> dial to select the self-timer delay. Q : 10-sec. self-timer k : 2-sec.
Page 278 MEMO...
Page 279: Image Settings
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. In Basic Zone modes, only the following can be set as described in this chapter: Image-recording quality, lens peripheral illumination correction, lens chromatic aberration correction, folder creation and selection, and image file...
Page 280: Setting The Image-Recording Quality
Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image- recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.118). Select [Image quality].
Page 281 Style, Custom Functions, and other settings. The maximum burst applies to <o> high-speed continuous shooting. Figures in parentheses apply to an UHS-I class 8 GB card based on Canon’s testing standards. Even if you use a UHS-I class card, the maximum burst indicator will not...
Page 282: Raw Images
3 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded simultaneously to he card in both RAW and JPEG at the image- recording quali ies that were set. The two images will be recorded with the same file numbers (file extension: .JPG for JPEG and .CR2 for RAW).
Page 283 3 Setting the Image-Recording Quality Maximum Burst During Continuous Shooting The approximate maximum burst is displayed on the bottom right in the viewfinder and on the shooting function settings screen. If the maximum burst for continuous shooting is 99 or higher, “99” will be displayed.
Page 284: I: Setting The Iso Speed
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically (p.122). Regarding the ISO speed during movie shooting, see pages 254 and 257.
Page 285 i: Setting the ISO SpeedN If [z4: Highlight tone priority] is set to [Enable], ISO 100/125/160 and “H” (equivalent to ISO 25600) cannot be set (p.145). Shooting in high temperatures may result in images that look grainier. Long exposures can also cause irregular colors in the image. When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable.
Page 286: Auto Iso
i: Setting the ISO SpeedN Auto ISO If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode.
Page 287 i: Setting the ISO SpeedN 3 Setting the ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within ISO 100 - ISO 12800 and the maximum limit within ISO 200 - H (equivalent to ISO 25600).
Page 288: Setting The Iso Speed Range For Auto Iso
i: Setting the ISO SpeedN 3 Setting the ISO Speed Range for Auto ISO You can set the automatic ISO speed range for Auto ISO within ISO 100 - ISO 12800. You can set the minimum limit within ISO 100 - ISO 6400, and the maximum limit within ISO 200 - ISO 12800 in whole-stop increments.
Page 289: Setting The Minimum Shutter Speed For Auto Iso
i: Setting the ISO SpeedN 3 Setting the Minimum Shutter Speed for Auto ISO When Auto ISO is set, you can set the minimum shutter speed (1/250 sec. to 1 sec.) so that the automatically-set shutter speed is not too slow.
Page 290: A Selecting A Picture Style
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, <D> (Auto) is set automatically. Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>.
Page 291 A Selecting a Picture StyleN R Landscape For vivid blues and greens, and very sharp and crisp images. Effective for impressive landscapes. S Neutral This Picture Style is for users who prefer to process images with their computer. For natural colors and subdued images. U Faithful This Picture Style is for users who prefer to process images with their computer.
Page 292 A Selecting a Picture StyleN Symbols The symbols of the Picture Style selection screen refer to parameters such as [Sharpness] and [Contrast]. The numerals indicate the parameter settings, such as for [Sharpness] and [Contrast], for each Picture Style. Symbols Sharpness Contrast Saturation Color tone...
Page 293: A Customizing A Picture Style
A Customizing a Picture StyleN You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see page 131. Select [Picture Style]. Under the [z4] tab, select [Picture Style], then press <0>.
Page 294 A Customizing a Picture StyleN Press the <M> button to save the adjusted parameters. The Picture Style selection screen will reappear. Any parameter settings different from the default will be displayed in blue. Parameter Settings and Effects g Sharpness 0: Less sharp outline +7: Sharp outline h Contrast -4: Low contrast...
Page 295 A Customizing a Picture StyleN V Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page. kFilter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more.
Page 296: A Registering A Picture Style
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create multiple Picture Styles with different settings for parameters such as sharpness and contrast.
Page 297 A Registering a Picture StyleN Select a parameter. Select a parameter such as [Sharpness], then press <0>. Set the parameter. Press the key to adjust the parameter as desired, then press <0>. For details, see “Customizing a Picture Style” on page 129. Press the <M>...
Page 298: White Balance
Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the <Q> (Auto) setting will obtain the correct white balance. If natural-looking colors cannot be obtained with <Q>, you can select the white balance to match the light source or set it manually by shooting a white object.
Page 299: O Custom White Balance
3 Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Perform this procedure under the actual light source to be used. Shoot a white object. Look through the viewfinder and aim the entire dotted line box (shown in the illustration) over a plain, white...
Page 300 3 Setting the White BalanceN Select [White balance]. Under the [z3] tab, select [White balance], then press <0>. Select the custom white balance. Select [ ], then press <0>. If he exposure obtained in step 1 differs greatly from he standard exposure, a correct white balance may not be obtained.
Page 301: P Setting The Color Temperature
3 Setting the White BalanceN P Setting the Color Temperature You can set the white balance’s color temperature numerically. This is for advanced users. Select [White balance]. Under the [z3] tab, select [White balance], then press <0>. Set the color temperature. Select [P].
Page 302: White Balance Correction
White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters.
Page 303: White Balance Auto Bracketing
3 White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images with different color tones can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/ green bias.
Page 304 Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically.
Page 305 Setting Noise ReductionN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced.
Page 306 3 Setting Noise ReductionN Cautions for Setting Multi Shot Noise Reduction If there is significant misalignment in the image due to camera shake, the noise reduction effect may be minimal. If you are handholding the camera, keep it steady to prevent camera shake.
Page 307 3 Setting Noise ReductionN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. Select [Long exp. noise reduction]. Under the [z4] tab, select [Long exp. noise reduction], then press <0>. Set the desired setting. Select the desired setting, then press <0>.
Page 308 3 Setting Noise ReductionN With [Auto] and [Enable], the noise reduction process after the picture is taken may take the same amount of time as hat for the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1”...
Page 309 Highlight Tone PriorityN You can minimize overexposed highlight areas. Select [Highlight tone priority]. Under the [z4] tab, select [Highlight tone priority], then press <0>. Select [Enable]. Select [Enable], then press <0>. Highlight details are improved. The dynamic range is expanded from the standard 18% gray to bright highlights.
Page 310: Lens Peripheral Illumination / Chromatic Aberration Correction
Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. Both lens aberrations can be corrected. The default settings are [Enable] for both corrections. Peripheral Illumination Correction Select [Lens aberration correction].
Page 311: Chromatic Aberration Correction
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction Select the setting. Check that [Correction data available] is displayed for the attached lens. Select [Chromatic aberration], then press <0>. Select [Enable], then press <0>. If [Correction data not available] is displayed, see “Lens Correction Data”...
Page 312 Peripheral illumination correction and chromatic aberration correction cannot be applied to JPEG images already taken. When using a non-Canon lens, setting the corrections to [Disable] is recommended, even if [Correction data available] is displayed. If you use magnified view during Live View shooting, the peripheral illumination correction and chromatic aberration correction will not be reflected in the image shown on the screen.
Page 313: Creating And Selecting A Folder
Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder Select [Select folder]. Under the [51] tab, select [Select folder], then press <0>.
Page 314: Selecting A Folder
3 Creating and Selecting a Folder Selecting a Folder With the folder selection screen Lowest file number displayed, select a folder and press Number of images in folder <0>. The folder where the captured images will be saved is selected. Subsequent captured images will be recorded into the selected folder.
Page 315: File Numbering Methods
File Numbering Methods The image files will be numbered from 0001 to 9999 in the order the images are IMG_0001.JPG (Example) taken, then saved in a folder. You can File number change how the file number is assigned. Select [File numbering]. Under the [51] tab, select [File numbering], then press <0>.
Page 316: Auto Reset
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. When you replace the card or create a folder, he file numbering restarts from 0001 for the new images saved.
Page 317: Setting Copyright Information
Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. Select [Copyright information]. Under the [54] tab, select [Copyright information], then press <0>. Select the option to be set. Select [Enter author’s name] or [Enter copyright details], then press <0>.
Page 318 3 Setting Copyright InformationN Exit the setting. After entering the text, press the <M> button, then select [OK]. The information will be saved and the screen will return to step 2. Checking the Copyright Information When you select [Display copyright info.] in step 2, you can check the [Author] and [Copyright] information that you entered.
Page 319: Setting The Color Space
Setting the Color SpaceN The range of reproducible colors is called the color space. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In Basic Zone modes, sRGB is set automatically. Select [Color space].
Page 320 MEMO...
Page 321: Advanced Operations
Advanced Operations In Creative Zone modes, you can set the shutter speed and/ or aperture to set the exposure as desired. By changing the camera settings, you can obtain various results. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
Page 322: D: Program Ae
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * <d> stands for Program. * AE stands for Auto Exposure. Set the Mode Dial to <d>. Focus the subject. Look through the viewfinder and aim the AF point over the subject.
Page 323 d: Program AE If he “30"” shutter speed and the lower f/number blink, it indicates underexposure. Increase the ISO speed or use flash. If he “8000” shutter speed and the higher f/number blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens.
Page 324: S: Shutter-Priority Ae
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion.
Page 325 s: Shutter-Priority AE If the lower f/number blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the higher f/number blinks, it indicates overexposure. Turn the <6>...
Page 326: F: Aperture-Priority Ae
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/ number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus.
Page 327 f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates underexposure. Turn the <6> dial to set a larger aperture (lower f/ number) until the shutter speed blinking stops or set a higher ISO speed. If the “8000"” shutter speed blinks, it indicates overexposure.
Page 328: A: Manual Exposure
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * <a>...
Page 329: Selecting The Metering Mode
q Selecting the Metering ModeN If Auto ISO is set, the ISO speed setting will change to suit the shutter speed and aperture in order to obtain a standard exposure. Therefore, you may not obtain the desired exposure effect. In [z3: Auto Lighting Optimizer], if the checkmark <X> for [Disabled in M or B modes] is removed, Auto Lighting Optimizer can be set in the <a>...
Page 330 q Selecting the Metering ModeN Partial metering Effective when the background is much brighter than the subject due to backlighting, etc. The metering is weighted at the center covering approx. 7.7% of the viewfinder area. Spot metering This is for metering a specific spot of the subject or scene.
Page 331: Setting Exposure Compensation
Setting Exposure CompensationN Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3- stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
Page 332: Auto Exposure Bracketing (Aeb)
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. Select [Expo.comp./AEB].
Page 333 h Auto Exposure Bracketing (AEB)N During AEB shooting, <A> in the viewfinder and <h> on the LCD panel will blink. If the drive mode is set to or , press the shutter button three times for each shot. When <o>, , or <M> is set and you hold down the shutter button completely, the three bracketed shots will be taken continuously and the camera will automatically stop shooting.
Page 334: A Ae Lock
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the <A> button to lock the exposure, then recompose and take the shot.
Page 335: F: Bu B Exposures
F: Bulb Exposures In this mode, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, astronomical objects, and other subjects requiring long exposures.
Page 336: W: Hdr (High Dynamic Range) Shooting
w: HDR (High Dynamic Range) ShootingN Highlight detail and shadow detail are retained for a high dynamic range of tones even with high-contrast scenes. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured for each shot and then merged together automatically.
Page 337 w: HDR (High Dynamic Range) ShootingN Set [Continuous HDR]. Select either [1 shot only] or [Every shot], then press <0>. With [1 shot only], HDR shooting will be canceled automatically after the shooting ends. With [Every shot], HDR shooting continues until the setting in step 2 is set to [Disable HDR].
Page 338 w: HDR (High Dynamic Range) ShootingN If you shoot a moving subject, the subject’s movement may leave afterimages or the surrounding area of the subject may become dark. To prevent camera shake, the ISO speed may be set higher than usual. HDR shooting is not possible with ISO expansion.
Page 339: P Multiple Exposures
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.215), you can see how the single exposures merge while shooting. Select [Multiple exposure]. Under the [z4] tab, select [Multiple exposure], then press <0>.
Page 340 P Multiple ExposuresN Set [Multi-expos ctrl]. Select the desired multiple-exposure control method, then press <0>. Additive The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation.
Page 341 P Multiple ExposuresN Set [Continue Mult-exp]. Select either [1 shot only] or [Continuously], then press <0>. With [1 shot only], multiple-exposure shooting will be canceled automatically after the shooting ends. With [Continuously], multiple- exposure shooting continues until the setting in step 2 is set to [Disable]. Take the first exposure.
Page 342 P Multiple ExposuresN Only the merged mul iple-exposure image will be saved. The images taken in steps 6 and 7 for the multiple-exposure image will not be saved. With multiple exposures, the more exposures there are, the more noticeable the noise, irregular colors, and banding will be. Also, as noise increases with higher ISO speeds, shooting at low ISO speeds is recommended.
Page 343 P Multiple ExposuresN Merging Multiple Exposures with an Image Recorded on the Card You can select an image recorded on the card as the first single exposure. The original of the selected image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images.
Page 344 P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single exposure. If you select [Deselect img], the selected image will be canceled. Checking and Deleting Multiple Exposures During Shooting Before you finish shooting the set number of exposures, you can press the <x>...
Page 345 P Multiple ExposuresN Are there any restrictions on the image-recording quality? All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Image-Recording Quality Setting Merged Multiple-Exposure JPEG JPEG 41/61 1+JPEG 1+JPEG...
Page 346: Mirror Lockup
2 Mirror LockupN Although using the self-timer or a remote switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). Set [Mirror lockup] to [Enable].
Page 347: Using The Eyepiece Cover
Using the Eyepiece Cover When you use the self-timer, bulb, or a remote switch and do not look through the viewfinder, stray light entering the viewfinder can cause the image to look dark. To prevent this, use the eyepiece cover (p.27) attached to the camera strap.
Page 348: F Using A Remote Switch
F Using a Remote Switch You can connect Remote Switch RS-60E3 (sold separately) to the camera and shoot (p.416). For detailed instructions, refer to the remote switch’s instruction manual. Open the terminal cover. Connect the plug to the remote control terminal. R Remote Control Shooting With Remote Controller RC-6 (sold separately), you can shoot remotely up to approx.
Page 349 R Remote Control Shooting Select the self-timer. Look at the LCD panel and turn the <6> dial to select <Q> or <k>. Press the remote controller's transmit button. Point the remote controller toward the camera’s remote control sensor and press the transmit button. The self-timer lamp lights up and the Remote picture is taken.
Page 350 MEMO...
Page 351: Flash Photography
Flash Photography This chapter explains how to use the built-in flash and external Speedlites (EX-series, sold separately), how to set flash settings with the menu, and how to use the built-in flash for wireless flash shooting. Flash cannot be used with movie shooting. (It will not fire.)
Page 352: D Using The Built-In Flash
D Using the Built-in Flash In Creative Zone modes, just press the <D> button to raise the built-in flash for flash photography. To retract the built-in flash, push it back down with your fingers. In Basic Zone modes (except <7> <3> <5>...
Page 353 D Using the Built-in Flash Effective Range of Built-in Flash [Approx. in meters/feet] EF-S18-55mm f/3.5-5.6 IS STM EF-S18-135mm f/3.5-5.6 IS STM ISO Speed EF-S18-200mm f/3.5-5.6 IS Wide Angle: f/3.5 Telephoto: f/5.6 1-3.4/3.3-11.2 1-2.1/3 3-7.0 1-4.8/3.3-15.9 1-3.0/3 3-9.9 1-6.9/3.3-22.5 1-4.3/3.3-14.1 1 2-9.7/4.0-31.8 1-6.1/3.3-19 9 1600 1.7-13.7/5.6-45.0...
Page 354: Red-Eye Reduction
D Using the Built-in Flash 3 Red-eye Reduction Using the red-eye reduction lamp before flash photography can reduce red eye. Red-eye reduction will function in any shooting mode except <7>, <3>, <5>, and <G>. Select [Red-eye reduc.]. Under the [z2] tab, select [Red-eye reduc.], then press <0>.
Page 355 D Using the Built-in Flash Select [y]. Press the <V> keys to select [y*], then press <0>. The flash exposure compensation screen will appear. Set the exposure compensation amount. To make the flash exposure brighter, turn the <5> or <6> dial to the right (increased exposure).
Page 356 D Using the Built-in Flash A FE LockN FE (flash exposure) lock obtains and locks the appropriate flash exposure for the desired part of the subject as framed. Press the <D> button. The built-in flash will rise. Press the shutter button halfway and look in the viewfinder to check that the <D>...
Page 357: D Using An External Speedlite
D Using an External Speedlite EOS-dedicated, EX-series Speedlites Flash photography with EX-series Speedlite (sold separately) is as easy as with built-in flash. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites.
Page 358 Cautions for Live View Shooting If you use a non-Canon flash unit with Live View shooting, set [A2: Silent LV shoot.] to [Disable] (p.231). The flash will not fire if it is set to [Mode 1] or [Mode 2].
Page 359: Setting The Flash
Setting the FlashN With the built-in flash or an EX-series Speedlite compatible with flash function settings, you can use the camera’s menu screen to set flash functions and the external Speedlite’s Custom Functions. If you use an external Speedlite, attach the Speedlite to the camera and turn on the Speedlite before setting the flash functions.
Page 360 3 Setting the FlashN Flash Synchronization Speed in Av Mode You can set the flash sync speed for flash photography in the aperture-priority AE (f) mode. : Auto The flash sync speed is set automatically within a range of 1/250 sec.
Page 361 3 Setting the FlashN Built-in Flash Settings Flash mode Normally, set this to [E-TTL II]. This enables autoexposure shooting with the built-in flash. To set the flash output level manually, select [Manual flash]. Select [2flash output], then set the flash output level to within 1/1 - 1/128 (1/3-stop increments) before shooting.
Page 362 3 Setting the FlashN 2 Flash exposure compensation The same setting as step 3 in “Flash Exposure Compensation” on page 190 can be set. Wireless functions With wireless flash photography (via optical transmission), you can use the built-in flash to control an external Speedlite.
Page 363 3 Setting the FlashN External Flash Function Settings The screen display and setting options will differ depending on the external Speedlite model, current flash mode, Speedlite’s Custom Function settings, etc. For details on your Speedlite’s flash functions, refer to the Speedlite’s instruction manual.
Page 364 3 Setting the FlashN Wireless functions Wireless (multiple) flash shooting is poss ble with radio or optical transmission. For details on wireless flash, refer to the instruction manual of a Speedlite compatible with the wireless flash shooting. Flash zoom (Flash coverage) With Speedlites having a zooming flash head, you can set the flash coverage.
Page 365 3 Setting the FlashN Flash exposure compensation The same setting as step 3 in “Flash Exposure Compensation” on page 190 can be set. For details, refer to the Speedlite’s instruction manual. Flash exposure bracketing While the flash output is changed automatically, three shots are taken.
Page 366: Clear Settings
3 Setting the FlashN External Speedlite Custom Function Settings For details on the external Speedlite’s Custom Functions, refer to the Speedlite’s instruction manual. Select [External flash C.Fn setting]. Select [External flash C.Fn setting], then press <0>. Set the desired function. Press the ...
Page 367: Using Wireless Flash
Using Wireless FlashN The camera’s built-in flash can work as a master unit with Canon Speedlites with a wireless slave feature via optical transmission and wirelessly trigger the Speedlite(s) to fire. Be sure to read about wireless flash photography (optical transmission) in the Speedlite’s instruction manual.
Page 368 Using Wireless FlashN *1: If the Speedlite does not have a transmission channel setting function, the camera can work with any channel. *2: In small rooms, the slave unit may work even if its wireless sensor does not face the camera. The camera’s wireless signals can bounce off the walls and be received by the slave unit.
Page 369 Using Wireless FlashN Wireless Flash Shooting Configurations The table below shows the possible configurations for wireless flash shooting. Choose the configuration suiting the subject, shooting conditions, and the number of external Speedlites you use. External Speedlite Setting Built-in Page A:B Flash Wireless Flash Quantity...
Page 370 Using Wireless FlashN Fully Automatic Shooting with One External Speedlite This shows the most basic setup for fully-automatic wireless flash shooting with one external Speedlite. Steps 1 to 4 and 6 apply to all wireless flash shooting. Therefore, these steps are omitted in the other wireless flash setups explained on the pages hereafter.
Page 371 Using Wireless FlashN Set [Flash mode: E-TTL II]. Set [Flash mode] to [E-TTL II]. Set [Wireless func.:0]. Set [Wireless func.] to [0]. Set [Channel]. Set the channel (1-4) to the same one as the slave unit. Set [Firing group:1All]. Set [Firing group] to [1All]. Take the picture.
Page 372 Using Wireless FlashN Fully Automatic Shooting with One External Speedlite and the Built-in Flash This is fully automatic wireless flash shooting with one external Speedlite and the built-in flash. You can change the flash ratio between the external Speedlite and built-in flash to adjust how the shadows look on the subject.
Page 373 Using Wireless FlashN Fully Automatic Shooting with Multiple External Speedlites Multiple Speedlite slave units can be treated as one flash unit or separated into slave groups whose flash ratio can be set. The basic settings are shown below. By changing the [Firing group] setting, you can shoot with various wireless flash setups with multiple Speedlites.
Page 374 Using Wireless FlashN [1 (A:B)] Multiple slave units in multiple groups Divide the slave units into Groups A and B and change the flash ratio to obtain the desired lighting effect. Refer to your Speedlite’s instruction manual to set one slave unit’s slave ID to A (Group A) and the other slave unit’s ID to B (Group B) and position them as shown in the illustration.
Page 375 Using Wireless FlashN Fully Automatic Shooting with the Built-in Flash and Multiple External Speedlites The built-in flash can also be added to wireless flash shooting explained on pages 209-210. The basic settings are shown below. By changing the [Firing group] setting, you can shoot with various wireless flash setups of multiple Speedlites complemented with the built-in flash.
Page 376 Using Wireless FlashN Creative Wireless Flash Shooting Flash exposure compensation When [Flash mode] is set to [E-TTL II], flash exposure compensation can be set. The flash exposure compensation settings that can be set (see below) will differ depending on the [Wireless func.] and [Firing group] settings.
Page 377 Using Wireless FlashN Setting the Flash Output Manually for Wireless Flash Shooting When [Flash mode] is set to [Manual flash], flash exposure can be set manually. The flash output settings that can be set ([1 flash output], [Group A output], etc.) will differ depending on the [Wireless func.] setting (see below).
Page 378 MEMO...
Page 379: Shooting With The Lcd Monitor
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to <A>. If you handhold the camera and shoot while viewing the LCD monitor, camera shake can cause blurred images.
Page 380: A Shooting With The Lcd Monitor
A Shooting with the LCD Monitor Set the Live View shooting/Movie shooting switch to <A>. Display the Live View image. Press the <0> button. The Live View image will appear on he LCD monitor. The Live View image will closely reflect the brightness level of the actual image you capture.
Page 381 A Shooting with the LCD Monitor Enabling Live View Shooting Set [A1: Live View shoot.] to [Enable]. Number of Possible Shots with Live View Shooting [Approx. number of shots] Room Temperature Low Temperatures Temperature ° ° ° ° C / 73 C / 32 No Flash 50% Flash Use...
Page 382 A Shooting with the LCD Monitor Information Display Each time you press the button, the information display will change. Possible shots AF method •c : u+Tracking Maximum burst/Number of remaining multiple exposures •o : FlexiZone - Multi Battery check •d : FlexiZone - Single AF point (FlexiZone - Single)
Page 383 A Shooting with the LCD Monitor Do not hold the camera in the same position for long periods of time. Even if the camera does not feel too hot, prolonged contact wi h the same body part may cause skin redness, blistering or low-temperature contact burns.
Page 384: Scene Icons
A Shooting with the LCD Monitor Scene Icons In the <A> shooting mode, the camera detects the scene type and sets everything automatically to suit the scene. The detected scene type is indicated on the upper left of the screen. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
Page 385 A Shooting with the LCD Monitor *5: Displayed with any of the lenses below: • EF-S18-55mm f/3.5-5.6 IS II • EF-S55-250mm f/4-5.6 IS II • EF300mm f/2.8L IS II USM • EF400mm f/2.8L IS II USM • Image Stabilizer lenses marketed in 2012 or later. *4+*5:If the conditions in both *4 and *5 are met, the shutter speed will slow down.
Page 386: Shooting Function Settings
Shooting Function Settings f / R / i / q / B Settings While the Live View image is displayed, if you press the <f>, <R>, , or <q> button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function.
Page 387 Shooting Function Settings Q Quick Control In Creative Zone modes, you can set the AF method, Drive mode, Metering mode, Image-recording quality, White balance, Picture Style, Auto Lighting Optimizer, and Creative Filters. In Basic Zone modes (except <F> and <G>), you can set the functions in bold and the settings shown in the table on page 91.
Page 388: U Shooting With Filter Effects
U Shooting with Filter Effects While viewing the Live View image, you can apply a filter effect (Grainy B/W, Soft focus, Fish-eye effect, Art bold effect, Water painting effect, Toy camera effect, or Miniature effect) before shooting. These are called Creative filters. When you take the picture, the camera saves only the image with the Creative filter applied.
Page 389 U Shooting with Filter Effects Adjust the filter effect. Press the button (except for the Miniature effect). Press the key to adjust the filter effect, then press <0>. For the Miniature effect, press <0>, then press the <V> key to move the white frame over the area you want the image look sharp.
Page 390 U Shooting with Filter Effects Creative Filter Characteristics Grainy B/W Creates a grainy black-and-white photo. You can change the black- and-white effect by adjusting the contrast. Soft focus Gives the image a soft look. You can change the degree of softness by adjusting the blur.
Page 391 U Shooting with Filter Effects Toy camera effect Darkens the photo’s corners and applies a color tone that makes it look as if it was shot by a toy camera. You can change the color cast by adjusting the color tone. Miniature effect Creates a diorama effect.
Page 392: Menu Function Settings
Menu Function Settings When the Live View shooting/Movie shooting switch is set to <A>, the Live View shooting menu options will appear under the [A1] and [A2] tabs. In Basic Zone modes, the [A2] tab and certain options under the [A1] tab will not appear.
Page 393 3 Menu Function Settings Touch Shutter Just by tapping the LCD monitor screen, you can focus and take the picture automatically. For details, see page 245. Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally.
Page 394 3 Menu Function Settings The asterisked image-recording quality settings do not match the respective aspect ratio exactly. The image area displayed for the asterisked aspect ratio is slightly larger than the recorded area. Check the captured images on the LCD monitor when shooting.
Page 395 If you use flash, silent shooting will not be possible regardless of the [Silent LV shoot.] setting. When using a non-Canon flash unit, set it to [Disable]. The flash will not fire if it is set to [Mode 1] or [Mode 2].
Page 396 3 Menu Function Settings Metering timerN You can change how long the exposure setting is displayed (AE lock time). Performing any of the following opera ions will stop Live View shooting. To start Live View shooting again, press the <0> button. •...
Page 397: Using Af To Focus (Af Method)
This can greatly affect the AF speed and the camera may take a longer time to focus (phase-difference detection generally allows faster AF focusing). For details, refer to Canon Web site. Selecting the AF Method You can select an AF method to suit the shooting conditions and your subject.
Page 398 Using AF to Focus (AF Method) Select an AF point. When a face is detected, the frame will appear over the face to be focused. If multiple faces are detected, <q> will be displayed. Use <9> to move the <q> frame over the face you want to focus on.
Page 399 Using AF to Focus (AF Method) If the subject’s face is significantly out of focus, face detection will not be possible. You can prevent this by setting [Continuous AF] to [Enable]. An object other than a human face may be detected as a face. Face detection will not work if the face is very small or large in the picture, too bright or too dark, or partially hidden.
Page 400 Using AF to Focus (AF Method) FlexiZone - Multi: o You can focus over a wide area with up to 31 AF points (automatic selection). This wide area can also be divided into 9 zones for focusing (zone selection). Display the Live View image. Press the <0>...
Page 401 Using AF to Focus (AF Method) Focus the subject. Aim the AF point over the subject and press the shutter button halfway. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the area frame will turn orange.
Page 402 Using AF to Focus (AF Method) FlexiZone - Single: d The camera focuses with a single AF point. This is effective when you want to focus a particular subject. Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor.
Page 403 Using AF to Focus (AF Method) Take the picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.216).
Page 404 Using AF to Focus (AF Method) Notes for u+Tracking / FlexiZone - Multi / FlexiZone - Single AF Operation Even when focus has been achieved, pressing the shutter button halfway will focus again. The image brightness may change during and after the AF operation.
Page 405 Using AF to Focus (AF Method) Shooting Conditions that Make Focusing Difficult Low-contrast subjects such as the blue sky, solid-color flat surfaces or when highlight or shadow details are lost. Subjects in low light. Stripes and other patterns where there is contrast only in the horizontal direction.
Page 406 Using AF to Focus (AF Method) If you cannot achieve focus under the shooting conditions listed on the preceding page, set the lens focus mode switch to <MF> and focus manually. If you shoot a peripheral subject and it is slightly out of focus, aim the center AF point or zone over the subject to focus, focus again, and then take the picture.
Page 407 Using AF to Focus (AF Method) Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.100), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation.
Page 408 Using AF to Focus (AF Method) The AF point (or zone) selection will change in the direction you tilt <9>. If you press <0>, the center AF point (or center Zone) will be selected. You can also use the <6> and <5>...
Page 409: Shooting With The Touch Shutter
x Shooting with the Touch Shutter Just by tapping the LCD monitor screen, you can focus and take the picture automatically. This works in all shooting modes. Display the Live View image. Press the <0> button. The Live View image will appear on the LCD monitor.
Page 410 x Shooting with the Touch Shutter Even if <o>, , or <M> is set, single shooting will take effect. The touch shutter does not function during magnified view. When [V Shutter butt. half-press] is set to [Metering start] or [AE lock (while button pressed)] under [8 C.Fn III-4: Custom Controls], autofocusing does not take effect.
Page 411: Mf: Focusing Manually
MF: Focusing Manually You can magnify the image and focus precisely with manual focus. Set the lens focus mode switch to <MF>. Turn the lens focusing ring to focus roughly. Display the magnifying frame. Press the button. The magnifying frame will appear. You can also tap [u] on the screen to magnify the image.
Page 412 MF: Focusing Manually Focus manually. While looking at the magnified image, turn the lens focusing ring to focus. After achieving focus, press the button to return to the normal view. Take the picture. Check the focus and exposure, then press the shutter button completely to take the picture (p.216).
Page 413 Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in the image. If Live View shooting is used continuously for a prolonged period, the camera’s internal temperature may rise, and image quality may deteriorate.
Page 414 Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect the brightness of the captured image. Even if a low ISO speed is set, noise may be noticeable in the displayed Live View image under low light.
Page 415: Shooting Movies
Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to <k>. The movie recording format will be MOV. For cards that can record movies, see page 3. If you handhold the camera and shoot movies, camera shake can cause blurred movies.
Page 416 k Shooting Movies Autoexposure Shooting When the shooting mode is set to other than <a>, autoexposure control will take effect to suit the scene’s current brightness. Set the shooting mode to a mode other than <a>. Set the Live View shooting/Movie shooting switch to <k>.
Page 417 k Shooting Movies In Basic Zone modes, he shooting result will be the same as in the <A> mode. Also, the scene icon for the scene detected by the camera is displayed on the upper left of the screen (p.255). In the <s>, <f>, or <F>...
Page 418 k Shooting Movies ISO Speed in Basic Zone Modes The ISO speed will be set automatically within ISO 100 - ISO 6400. ISO Speed in the d, s, f, and F Mode The ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [12800/H] (p.123), the maximum ISO speed for the automatic ISO speed setting will be expanded to H...
Page 419 k Shooting Movies Scene Icons During movie shooting in a Basic Zone mode, an icon representing the scene detected by the camera will be displayed and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
Page 420 k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. Set the Mode Dial to <a>. Set the Live View shooting/Movie shooting switch to <k>.
Page 421 k Shooting Movies ISO Speed During Manual Exposure Shooting With [Auto] (A), the ISO speed will be set automatically within ISO 100 - ISO 6400. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [12800/H] (p.123), the maximum ISO speed will be expanded and the ISO speed will be set automatically within ISO 100 to H (equivalent to ISO 12800).
Page 422 k Shooting Movies Information Display Each time you press the button, the information display will change. Possible shots AF method •c : u + Tracking Maximum burst •o: FlexiZone - Multi Movie shooting remaining time*/ •d : FlexiZone - Single Elapsed time Movie shooting mode Battery check...
Page 423 k Shooting Movies Notes on Movie Shooting Do not hold the camera in the same position for long periods of time. Even if the camera does not feel too hot, prolonged contact wi h the same body part may cause skin redness, blistering or low-temperature contact burns.
Page 424 k Shooting Movies Notes on Movie Shooting You can use Remote Controller RC-6 (sold separately, p.184) to start and stop the movie shooting if the drive mode is <Q> or <k>. Set the shoo ing timing switch to <2> (2-sec. delay), then press the transmit button.
Page 425: Shooting Still Photos
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking Still Photos during Movie Shooting If you take a still photo during movie shooting, the movie will record a still moment lasting approx.
Page 426 k Shooting Movies AEB cannot be used. Even if a flash is used, it will not fire. Con inuous s ill photo shooting is possible during movie shooting. However, the captured images will not be displayed on the screen. Depending on the still photo’s image-recording quality, number of shots during continuous shooting, card performance, etc., movie shooting may stop automatically.
Page 427: Shooting Function Settings
Shooting Function Settings f / R / i Settings While the movie image is displayed on the LCD monitor, if you press the <f> or <R> button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function.
Page 428 Shooting Function Settings Q Quick Control In Creative Zone modes, you can set the AF method, Drive mode, Movie recording size, Digital zoom, White balance, Picture Style, Auto Lighting Optimizer, and Video snapshots. In Basic Zone modes, only the functions in bold can be set. Press the <Q>...
Page 429: Setting The Movie Recording Size
Setting the Movie Recording Size With [Z2: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image Size A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9.
Page 430 3 Setting the Movie Recording Size Total Movie Recording Time and File Size Per Minute Total Recording Time (approx.) Movie Recording File Size Size (approx.) 4 GB Card 8 GB Card 16 GB Card 654 X 16 min. 32 min. 1 hr.
Page 431: Using Movie Digital Zoom
Using Movie Digital Zoom When the movie size is [1920x1080] (Full HD), you can shoot with an approx. 3x to 10x digital zoom. Select [Digital zoom]. Under the [Z2] tab, select [Digital zoom], then press <0>. Select [Approx. 3-10x zoom]. Select [Approx.
Page 432: Setting The Sound Recording
Setting the Sound Recording You can shoot movies while recording sound with the built-in stereo microphone or a commercially-available stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [Z2: Sound recording]. Sound Recording/Sound-Recording Level [Auto] : The sound-recording level is adjusted automatically.
Page 433 3 Setting the Sound Recording Using the Microphone The built-in microphone records stereo sound. Stereo sound recording is also possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (φ3.5 mm) to the camera’s external microphone IN terminal (p.20). In Basic Zone modes, he set ings available for [Sound recording] will be [On/Off].
Page 434: Setting The Time Code
Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing.
Page 435 3 Setting the Time Code Movie Recording Count You can select what to display on the movie-shooting screen. [Rec time] : Indicates the elapsed time from the start of the movie shooting. [Time code] : Indicates the time code during movie shooting. Movie Playback Count You can select what to display on the movie playback screen.
Page 436 3 Setting the Time Code Drop Frame If the frame rate setting is 6 (29.97 fps) or 8 (59.94 fps), the time code’s frame count causes a discrepancy between the actual time and time code. This discrepancy can be corrected automatically. This correction function is called drop frame.
Page 437: Menu Function Settings
Menu Function Settings When the Live View shooting/Movie shooting switch is set to <k>, the [Z1] and [Z2] tabs dedicated to movie shooting will be displayed. AF method The AF methods are the same as described on pages 233-242. You can select [u+Tracking], [FlexiZone - Multi], or [FlexiZone - Single].
Page 438 3 Menu Function Settings • If you want to keep the focus at a specific point or you do not want the lens operation noise to be recorded, you can temporarily stop Movie Servo AF as follows. When you stop Movie Servo AF, the AF point will turn gray.
Page 439 3 Menu Function Settings Silent LV shootingN This function applies to still photo shooting. For details, see page 231. Metering timerN You can change how long the exposure setting is displayed (AE lock time).
Page 440 3 Menu Function Settings Grid display With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you align the intersections over the subject for better balance in the composition.
Page 441: Shooting Video Snapshots
Shooting Video Snapshots A video snapshot is a short video clip lasting about 2 sec., 4 sec., or 8 sec. A series of video snapshots can be strung together to form a video snapshot album to show highlights of a trip, event, etc. A video snapshot album can also be played together with background music (p.284, 309).
Page 442 3 Shooting Video Snapshots Select [Album settings]. Select [Album settings], then press <0>. Select [Create a new album]. Select [Create a new album], then press <0>. Select the snapshot length. Press <0> and use the <V> key to select the snapshot’s length, then press <0>.
Page 443 3 Shooting Video Snapshots Creating a Video Snapshot Album Shoot the first video snapshot. Press the <0> button, then shoot. The blue bar indicating the shooting duration will gradually decrease. After the set shooting duration elapses, the shooting stops automatically. The confirmation dialog will appear (p.280).
Page 444 3 Shooting Video Snapshots Options in Steps 8 and 9 Function Description JSave as album The movie clip will be saved as the video (Step 8) snapshot album’s first video snapshot. The video snapshot just shot will be JAdd to album added to the album recorded immediately (Step 9) before.
Page 445 3 Shooting Video Snapshots [Playback video snapshot] Operations Function Playback Description By pressing <0>, you can play or pause the just- Play recorded video snapshot. First frame Displays the first scene of the album’s first video snapshot. Each time you press <0>, the video snapshot skips back Skip backward* by a few seconds.
Page 446 3 Shooting Video Snapshots Adding to an Existing Album Select [Add to existing album]. Follow step 4 on page 278 to select [Add to existing album], then press <0>. Select an existing album. Turn the <5> dial to select an existing album, then press <0>.
Page 447 3 Shooting Video Snapshots Cautions for Shooting Video Snapshots You can add to an album only video snapshots with the same duration (approx. 2 sec., 4 sec., or 8 sec. each). Note hat if you do any of the following while shoo ing video snapshots, a new album will be created for subsequent video snapshots.
Page 448 3 Shooting Video Snapshots Playing an Album You can play a video snapshot a bum in the same way as a normal movie (p.308). Play back the movie. Press the <x> button to display an image. Select the album. In the single-image display, the ] icon displayed on the upper left of the screen indicates a video snapshot album.
Page 449 3 Shooting Video Snapshots Editing an Album After shooting, you can rearrange, delete, or play back the video snapshots in the album. Select [X]. On the movie playback panel displayed, select [X] (Edit), then press <0>. The editing screen will be displayed. Select an editing operation.
Page 450: Save The Edited Movie
3 Shooting Video Snapshots Save the edited movie. Press the <M> button to return to the Editing panel at the screen’s bottom. Select [W] (Save), then press <0>. The save screen will appear. To save it as a new movie, select [New file].
Page 451 Movie Shooting Cautions White <s> and Red <E> Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie shooting or under a high ambient temperature, a white <s> or red <E> icon will appear. The white <s> icon indicates that the image quality of still photos will deteriorate.
Page 452 Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory).
Page 453: Image Playback
Image Playback This chapter explains how to play back and erase photos and movies, how to display them on a TV screen, and other playback-related functions. Images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or that have had their file names changed.
Page 454 x Image Playback Single-Image Display Play back the image. Press the <x> button. The last captured image or last image played back will appear. Select an image. To play back images starting with the last image, turn the <5> dial counterclockwise.
Page 455: Grid Display
x Image Playback Exit the image playback. Press the <x> button to exit the image playback and return to shooting-ready state. 3 Grid Display On the single-image display, you can overlay a playback grid. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag This function is convenient for checking the image’s vertical or horizontal tilt, as...
Page 456: B: Shooting Information Display
B: Shooting Information Display Sample Still Photo Taken in a Creative Zone Mode AF Microadjustment Exposure compensation amount Protect images Flash exposure compensation Rating amount / HDR mode / Multi Shot Noise Reduction Folder number - File number Aperture Histogram Shutter speed (Brightness/RGB) Picture Style/...
Page 457 B: Shooting Information Display Sample Still Photo Taken in a Basic Zone Mode Ambience and Shooting mode ambience effects Lighting or scene * With images taken in a Basic Zone mode, the information displayed will differ depending on the shooting mode. * [Background blur] will be displayed for images taken in the <C>...
Page 458 B: Shooting Information Display Highlight Alert When [33: Highlight alert] is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed, blinking areas, set the exposure compensation to a negative amount and shoot again. AF Point Display When [33: AF point disp.] is set to [Enable], the AF point that achieved focus will be displayed in red.
Page 459 B: Shooting Information Display Histogram The brightness histogram shows the exposure level distribution and overall brightness. The RGB histogram is for checking the color saturation and gradation. The display can be switched with [33: Histogram disp.]. [Brightness] Display Sample Histograms This histogram is a graph showing the distribution of the image’s brightness level.
Page 460 x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing four or nine images on one screen. Switch to the index display. During image playback, press the ...
Page 461 x Searching for Images Quickly Jump through Images (Jump Display) In the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. Select [Image jump w/6]. Under the [32] tab, select [Image jump w/6], then press <0>.
Page 462: U/Y Magnified View
u/y Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. Magnify the image. Press the button during image playback. The image will be magnified. If you hold down the button, the image will be magnified until it reaches the maximum magnification.
Page 463: Playing Back With The Touch Screen
d Playing Back with the Touch Screen The LCD monitor is a touch-sensitive panel that you can touch with your fingers for various playback operations. First, press the <x> button to play back images. Browsing Images Swipe with one finger. With single-image display, touch the LCD monitor with one finger.
Page 464 d Playing Back with the Touch Screen Reducing Image (Index Display) Pinch two fingers. Touch the screen with two fingers spread apart, then pinch your fingers together on the screen. Each time you pinch your fingers, the screen changes from a single-image display to a 4-image index display and 9-image index display.
Page 465: Rotating The Image
b Rotating the Image You can rotate the displayed image to the desired orientation. Select [Rotate image]. Under the [31] tab, select [Rotate image], then press <0>. Select an image. Turn the <5> dial to select the image to be rotated. You can also select an image in the index display (p.296).
Page 466: Setting Ratings
Setting Ratings You can rate images (still photos and movies) with one of five rating marks: l/m/n/o/p. This function is called rating. Select [Rating]. Under the [32] tab, select [Rating], then press <0>. Select an image. Turn the <5> dial to select the image or movie to be rated.
Page 467 3 Setting Ratings The total number of images with a given rating that can be displayed is up to 999. If there are more than 999 images with a given rating, [###] will be displayed for that rating. Taking Advantage of Ratings With [32: Image jump w/6], you can display only images with a specific rating.
Page 468: Q Quick Control For Playback
Q Quick Control for Playback During single-image display, you can press the <Q> button to set any of the following: [J: Protect images, b: Rotate image, 9: Rating, U: Creative filters, S: Resize (JPEG image only), : Highlight alert, : AF point display, e: Image jump w/6, k: Wi-Fi*]. For movies, only the functions in bold above can be set.
Page 469 Q Quick Control for Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the <Q>...
Page 470: Enjoying Movies
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV Set (p.316, 319) Use the HDMI cable HTC-100 (sold separately) or stereo AV cable AVC- DC400ST (sold separately) to connect the camera to a TV set. Then you can play back captured movies and still photos on TV.
Page 471 k Enjoying Movies Playback and Editing with a Computer (p.456) The movie files recorded on the card can be transferred to a computer and played with ImageBrowser EX (provided software). To have the movie play back smoothly on a computer, use a high- performance computer.
Page 472: Playing Movies
k Playing Movies Play back the image. Press the <x> button to display an image. Select a movie. Turn the <5> dial to select the movie to be played. In the single-image display, the <s1> icon displayed on the upper left of the screen indicates a movie.
Page 473 k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. Adjust the slow motion speed by pressing the key. 8 Slow motion The slow motion speed is indicated at the upper right of the screen.
Page 474: Editing A Movie's First And Last Scenes
X Editing a Movie’s First and Last Scenes Playback with the Touch Screen Tap [7] at the center of the screen. The movie will start playing. To display the movie playback panel, tap <s1> on the upper left of the screen.
Page 475 X Editing a Movie’s First and Last Scenes Check the edited movie. Select [7] and press <0> to play back the edited movie. To change the editing, go back to step To cancel the editing, press the <M> button, then select [OK] on the confirmation screen.
Page 476: Slide Show (Auto Playback)
Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. Select [Slide show]. Under the [32] tab, select [Slide show], then press <0>. Select the images to be played. Number of images to be played Press the <V>...
Page 477 3 Slide Show (Auto Playback) Item Playback Description All the s ill photos and movies on the card will be played jAll images back. Still photos and movies taken on the selected shooting date iDate will be played back. Still photos and movies in the selected folder will be played nFolder back.
Page 478: Start The Slide Show
3 Slide Show (Auto Playback) [Transition effect] [Background music] Start the slide show. Press the <V> key to select [Start], then press <0>. After [Loading image...] is displayed, the slide show will start. Exit the slide show. To exit the slide show and return to the setting screen, press the <M>...
Page 479 3 Slide Show (Auto Playback) Selecting the Background Music After you use EOS Utility (provided software) to copy background music to the card, you can play background music together with the slide show. Select [Background music]. Set [Background music] to [On], then press <0>.
Page 480: Viewing Images On A Tv Set
Viewing Images on a TV Set You can view still photos and movies on a TV set. Viewing on High-Definition (HD) TV Sets (Connected with HDMI) HDMI Cable HTC-100 (sold separately) is required. Connect the HDMI cable to the camera. With the plug’s <dHDMI MINI>...
Page 481 Viewing Images on a TV Set Press the <x> button. The image will appear on the TV screen. (Nothing will be displayed on the camera’s LCD monitor.) The images will automatically be displayed at the TV’s optimum resolution. By pressing the button, you can change the display format.
Page 482 Viewing Images on a TV Set Connect the camera to a TV set. Use an HDMI cable to connect the camera to the TV. The TV’s input will switch automatically to the HDMI port connected to the camera. Press the camera’s <x> button. An image will appear on the TV screen and you can use the TV’s remote control to play back images.
Page 483 Viewing on Non-HD TV Sets (Connected with AV Cable) Stereo AV Cable AVC-DC400ST (sold separately) is required. Connect the AV cable to the camera. With the plug’s <Canon> logo facing the back of the camera, insert it into the <q> terminal. Connect the AV cable to the TV (Red) set.
Page 484: K Protecting Images
K Protecting Images Protecting an image prevents it from being erased accidentally. 3 Protecting a Single Image Select [Protect images]. Under the [31] tab, select [Protect images], then press <0>. Select [Select images]. Select [Select images], then press <0>. An image will be displayed. Protect the image.
Page 485 K Protecting Images 3 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at one time. When you select [All images in folder] or [All images on card] in [31: Protect images], all the images in the folder or on the card will be protected.
Page 486: L Erasing Images
L Erasing Images You can either select and erase unnecessary images one by one or erase them in one batch. Protected images (p.320) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them.
Page 487 L Erasing Images Select [Select and erase images]. Select [Select and erase images], then press <0>. An image will be displayed. To display the three-image display, press the button. To return to the single-image display, press the button. Select the images to be erased.
Page 488: Changing Image Playback Settings
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. Select [LCD brightness]. Under the [52] tab, select [LCD brightness], then press <0>. Adjust the brightness. While referring to the gray chart, press the ...
Page 489: Auto Rotation Of Vertical Images
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the computer instead of horizontally. You can change the setting for this feature. Select [Auto rotate].
Page 490 MEMO...
Page 491: Post-Processing Images
Post-Processing Images You can process RAW images with the camera, resize (reduce the pixel count of) JPEG images, and apply Creative filters. The M icon at the upper right of the page title indicates that the function is available only in Creative Zone modes (d/ s/f/a/F).
Page 492 R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. While the RAW image itself does not change, you can process the RAW image according to different conditions to create any number of JPEG images from it.
Page 493 R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the setting screen. Turn the <5> or <6> dial to change the setting. To finalize the change and return to the screen in step 3, press <0>. Save the image.
Page 494 R Processing RAW Images with the CameraN RAW Image Processing Options Brightness adjustment You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. Picture Style (p.126) You can select the Picture Style. Press the key to select the Picture Style.
Page 495 R Processing RAW Images with the CameraN Color space (p.155) You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.146) If [Enable] is set, the corrected image will be displayed.
Page 496 R Processing RAW Images with the CameraN Peripheral Illumination Correction, Distortion Correction, and Chromatic Aberration Correction To execute peripheral illumination correction, distortion correction, and chromatic aberration correction with the camera, the data of the lens used for the shot must be registered in the camera. If the lens data has not been registered in the camera, use EOS U ility (provided software, p.456) to register he lens data.
Page 497: S Resizing Jpeg Images
S Resizing JPEG Images You can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/4/a/b images. JPEG c and RAW images cannot be resized. Select [Resize].
Page 498 S Resizing JPEG Images Resize Options According to Original Image Size Available Resize Settings Original Image Size Image Sizes The image size displayed in step 3 on the preceding page, such as [***M ****x****], has a 3:2 aspect ratio. The image size according to aspect ratios is shown in the table below.
Page 499: U Applying Creative Filters
U Applying Creative Filters You can apply the following Creative filters to an image and save it as a new image: Grainy B/W, Soft focus, Fish-eye effect, Art bold effect, Water painting effect, Toy camera effect, and Miniature effect. Select [Creative filters]. Under the [x1] tab, select [Creative filters], then press <0>.
Page 500 U Applying Creative Filters Save the image. Select [OK] to save the image. Check the destination folder and image file number, then select [OK]. To apply a filter to another image, repeat steps 2 to 5. To return to the menu, press the <M>...
Page 501 U Applying Creative Filters Fish-eye effect Gives the effect of a fish-eye lens. The image will have a barrel-type distortion. Depending on the level of this filter effect, the area trimmed along the periphery of the image changes. Also, since this filter effect will magnify the image center, the apparent resolution at the center may degrade depending on the number of recorded pixels.
Page 502 MEMO...
Page 503: Sensor Cleaning
If visible spots still remain after the automatic sensor cleaning, having the sensor cleaned by a Canon Service Center is recommended. Even while the Self Cleaning Sensor Unit is operating, you can press the shutter button halfway to interrupt the cleaning and start shooting immediately.
Page 504: Automatic Sensor Cleaning
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation.
Page 505 Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later.
Page 506: Dust Delete Data
3 Appending Dust Delete DataN Shoot a solid-white object. At a distance of 20 cm - 30 cm (0.7 ft. - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. The picture will be taken in aperture- priority AE mode at an aperture of f/22.
Page 507 Before cleaning the sensor, detach the lens from the camera. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Select [Sensor cleaning].
Page 508 If he battery level becomes low while you clean the sensor, the beeper will sound as a warning. Stop cleaning the sensor. If a smudge that cannot be removed with a blower remains, having he sensor cleaned by a Canon Service Center is recommended.
Page 509: Printing Images
Printing Images Printing (p.348) You can connect the camera directly to a printer and print out the images on the card. The camera is compatible with “wPictBridge”, which is the standard for direct printing. You can also use a wireless LAN to send images to a PictBridge (DPS over IP) printer and print them.
Page 510: Preparing To Print
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor. Connecting the Camera to a Printer Set the camera’s power switch to <2>. Set up the printer. For details, refer to the printer’s instruction manual.
Page 511 Preparing to Print Play back the image. PictBridge Press the < > button. The image will appear, with the <w> icon on the upper left of the screen to indicate that the camera is connected to a printer. Make sure the printer has a PictBridge connection port. Movies cannot be printed.
Page 512: Printing
w Printing The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon Select the image to be printed. Check that the <w> icon is displayed on the upper left of the LCD monitor.
Page 513 w Printing Q Setting the Paper Size Select the size of the paper loaded in the printer, then press <0>. The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in the printer, then press <0>. The page layout screen will appear.
Page 514: Set The Printing Effects
w Printing Set the printing effects. Set them if necessary. If you do not need to set any printing effects, go to step 5. What is displayed on the screen differs depending on the printer. Select the option, then press <0>. Select the desired printing effect, then press <0>.
Page 515: Start Printing
w Printing Set the date and file number imprinting. Set them if necessary. Select < >, then press <0>. Set the print settings as desired, then press <0>. Set the number of copies. Set it if necessary. Select < >, then press <0>. Select the number of copies, then press <0>.
Page 516 w Printing e Adjustment of Printing Effects In step 4 on page 350, select the printing effect. When the <e> icon is displayed brightly next to <z>, you can press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4.
Page 517 w Printing Cropping the Image You can crop the image and print only an Tilt correction enlarged version of the cropped portion, as if the image had been recomposed. Set the cropping right before printing. If you change the print settings after setting the cropping, you may have to set the cropping again before printing.
Page 518 w Printing Depending on the printer, the cropped image area may not be printed as you specified. The smaller you make the cropping frame, he grainier the picture will look in the print. While cropping the image, look at the camera’s LCD monitor. If you look at the image on a TV screen, the cropping frame may not be displayed accurately.
Page 519: W Digital Print Order Format (Dpof)
W Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options Select [Print order].
Page 520 W Digital Print Order Format (DPOF) Standard Prints one image on one sheet. Multiple thumbnail images are printed on Index one sheet. Print type Both Prints both the standard and index prints. Date [On] imprints the recorded date on the print. File number [On] imprints the file number on the print.
Page 521: Print Ordering
W Digital Print Order Format (DPOF) Print Ordering Sel.Image Select and order images one by one. To display the three-image display, press the button. To return to the single-image display, press the button. Press the <M> button to save the print order to the card.
Page 522: W Direct Printing Of Print-Ordered Images
W Direct Printing of Print-Ordered Images With a PictBridge printer, you can easily print images with DPOF. Prepare to print. See page 346. Follow the “Connecting the Camera to a Printer” procedure up to step 5. Under the [31] tab, select [Print order]. Select [Print].
Page 523: Specifying Images For A Photobook
p Specifying Images for a Photobook When you select images to use in photobooks (up to 998 images) and use EOS Utility (provided software) to transfer them to a computer, the selected images will be copied into a dedicated folder. This function is useful for ordering photobooks online.
Page 524 p Specifying Images for a Photobook Specifying All Images in a Folder or on a Card You can specify all the images in a folder or on a card at one time. When [x1: Photobook Set-up] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be specified.
Page 525: Customizing The Camera
Customizing the Camera You can customize various camera functions to suit your picture-taking preferences with Custom Functions. Also, the current camera settings can be saved under the Mode Dial <w> position. The functions explained in this chapter work only in the Creative Zone modes.
Page 526: Custom Functions
Setting Custom FunctionsN Select [8]. Select the group. Select C.Fn I, II, or III, then press <0>. Select the Custom Function Custom Function number number. Press the key to select the Custom Function number, then press <0>. Change the setting as desired. Select the desired setting (number), then press <0>.
Page 527: C.fn I: Exposure
Custom FunctionsN k Movie A LV C.Fn I: Exposure Shooting Shooting Exposure level increments p.365 In a ISO speed setting increments p.365 Bracketing auto cancel p.365 (Still photo, Bracketing sequence p.366 with WB bracketing) Number of bracketed shots p.366 Safety shift p.367 C.Fn II: Autofocus Tracking sensitivity...
Page 528: C.fn Iii: Operation/Others
3 Custom FunctionsN C.Fn III: Operation/Others Dial direction during Tv/Av p.375 Multi function lock p.375 Warnings z in viewfinder p.376 Custom Controls p.376 Depends on setting...
Page 529 Custom Function SettingsN C.Fn I: Exposure C.Fn I -1 Exposure level increments 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. This is effective when you prefer to control the exposure in less fine increments than 1/3- stop increments.
Page 530 3 Custom Function SettingsN C.Fn I -4 Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0: 09-9+ 1: -909+ 2: +909- White Balance Bracketing B/A Direction M/G Direction 0 : Standard exposure 0 : Standard white balance 0 : Standard white balance - : Decreased exposure - : Blue bias - : Magenta bias + : Increased exposure + : Amber bias...
Page 531 3 Custom Function SettingsN C.Fn I -6 Safety shift 0: Disable 1: Shutter speed/Aperture This takes effect in the shutter-priority AE (s) and aperture-priority AE (f) modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure.
Page 532 3 Custom Function SettingsN C.Fn II: Autofocus C.Fn II -1 Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. Default setting suited for most subjects. Suited for normal, moving subjects. Locked on: -2 / Locked on: -1 The camera will try to continue focusing the subject even if an obstacle enters he AF points or if the subject strays from the AF points.
Page 533 3 Custom Function SettingsN C.Fn II -2 Acceleration/deceleration tracking This sets he tracking sensitivity for moving subjects whose speed can suddenly change drama ically by starting or stopping suddenly, etc. Suited for subjects that move at a fixed speed. +2 / +1: Effective for subjects having sudden movements, sudden acceleration/ deceleration, or sudden stops.
Page 534 3 Custom Function SettingsN C.Fn II -4 AI Servo 2nd image priority You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF. Equal priority: Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, shooting speed may slow down.
Page 535 3 Custom Function SettingsN C.Fn II -5 AF-assist beam firing Enables or disables the AF-assist beam emitted by the built-in flash or EOS- dedicated external Speedlite. 0: Enable The AF-assist beam will be emitted when necessary. 1: Disable The AF-assist beam is not emitted. This prevents the AF-assist beam from disturbing others.
Page 536 3 Custom Function SettingsN C.Fn II -7 Select AF area selection mode You can limit the selectable AF area selection modes to suit your shooting preferences. Select the mode you want to use, then press <0> to append a checkmark <X> and select [OK]. : Manual selection: 1 pt AF You can select one AF point.
Page 537 3 Custom Function SettingsN C.Fn II -9 Orientation linked AF point You can set the AF area selection mode and manually-selected AF point separately for vertical shooting and horizontal shooting. 0: Same for both vertical/horizontal The same AF area selection mode and manually-selected AF point (or zone) are used for both vertical shooting and horizontal shooting.
Page 538 3 Custom Function SettingsN C.Fn II -11 AF point display during focus You can set whether or not to display the AF point(s) in the following cases: 1. When selecting the AF point(s), 2. When the camera is ready to shoot (before AF operation), 3.
Page 539 3 Custom Function SettingsN C.Fn II -13 AF Microadjustment Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. For details, see page 377. C.Fn III: Operation/Others C.Fn III -1 Dial direction during Tv/Av 0: Normal 1: Reverse direction...
Page 540 3 Custom Function SettingsN Warnings z in viewfinder C.Fn III -3 When any of the following functions are set, the <z> icon can be displayed on the viewfinder’s bottom right (p.23). The <z> icon will also appear on the shooting function settings display (p.49). Select the function for which you want the warning icon to appear, press <0>...
Page 541: 8: Fine Adjustment Of Af's Point Of Focus
8: Fine Adjustment of AF’s Point of Focus Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. This is called “AF Microadjustment”. Before making the adjustment, read “Notes for AF Microadjustment”...
Page 542 8: Fine Adjustment of AF’s Point of Focus Make the adjustment. Press the key to make the adjustment. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the point of focus in front of the standard point of focus.
Page 543 8: Fine Adjustment of AF’s Point of Focus 2: Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment has been registered, the point of focus will always be shifted by the adjustment amount.
Page 544 8: Fine Adjustment of AF’s Point of Focus Enter the serial number. Press the key to select the digit to be entered, then press <0> to display <r>. Press the <V> key to enter the number, then press <0>. After entering all the digits, select [OK] and press <0>.
Page 545 8: Fine Adjustment of AF’s Point of Focus Make the adjustment. Single focal length lens For a zoom lens, press the <V> key and select the wide-angle (W) or telephoto (T) end. Press <0> and the box will disappear, allowing you to make the adjustment.
Page 546 8: Fine Adjustment of AF’s Point of Focus When shooting with the intermediate range (focal length) of a zoom lens, the AF’s point of focus is corrected automatically rela ive to the adjustments made for the wide-angle and telephoto ends. Even if only the wide-angle or telephoto end has been adjusted, a correc ion will be made automatically for the intermediate range.
Page 547: 8: Custom Controls
8: Custom Controls You can assign often-used functions to camera buttons or dials according to your preferences. Select [C.Fn III: Operation/ Others]. Under the [8] tab, select [C.Fn III: Operation/Others], then press <0>. Select [4: Custom Controls]. Select [4: Custom Controls], then press <0>.
Page 548 8: Custom Controls Assignable Functions to Camera Controls Func ion Page Metering and AF start AF stop ONE SHOT z AI SERVO AF point direct selection Metering start AE lock/FE lock AE lock AE lock (while button pressed) Exposure AE lock (hold) FE lock Set ISO speed (hold button, turn Shutter speed setting in M mode...
Page 549 8: Custom Controls * The AF stop button ( ) is provided only on super telephoto IS lenses.
Page 550 8: Custom Controls : Metering and AF start When you press the button assigned to this function, metering and AF are executed. : AF stop The AF will stop while you hold down the button assigned to this function. Convenient when you want to lock the focus during AI Servo : ONE SHOT z AI SERVO You can switch the AF operation.
Page 551 8: Custom Controls : AE lock When you press the button assigned to this function, you can lock the exposure (AE lock) during the metering. Convenient when you want to focus and meter the shot at different areas or when you want to take multiple shots at the same exposure setting.
Page 552 8: Custom Controls : Flash exposure compensation Press <0> to display the flash exposure compensation setting screen (p.190) on the LCD monitor. : Image quality Press <0> to display the image-recording quality setting screen (p.116) on the LCD monitor. : Picture Style Press <0>...
Page 553 Registering My MenuN Under the My Menu tab, you can register up to six menu options and Custom Functions whose settings you change frequently. Select [My Menu settings]. Under the [9] tab, select [My Menu settings], then press <0>. Select [Register to My Menu]. Select [Register to My Menu], then press <0>.
Page 554 w: Register Custom Shooting ModesN You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial <w> position. Select [Custom shooting mode (C mode)]. Under the [54] tab, select [Custom shooting mode (C mode ], then press <0>.
Page 555 w: Register Custom Shooting ModesN Settings Registered Shooting Function Settings Shooting mode, Shutter speed, Aperture, ISO speed, Exposure compensation, Flash exposure compensation, AF operation, AF point, Drive mode, Metering mode. Menu functions Image quality, VF grid display l, Viewfinder level, Beep, Release shutter without card, Image review Lens aberration correction (Peripheral illumination, Chromatic aberration), Flash control, E-TTL II metering, Flash sync.
Page 556 w: Register Custom Shooting ModesN C.Fn I: Exposure Exposure level increments, ISO speed setting increments, Bracketing auto cancel, Bracketing sequence, Number of bracketed shots, Safety shift C.Fn II: Autofocus Tracking sensitivity, Acceleration/deceleration tracking, AI Servo 1st image priority, AI Servo 2nd image priority, AF- assist beam firing, Lens drive when AF impossible, Select AF area selection mode, AF area selection method, Orientation linked AF point, Manual AF point selection pattern, AF point...
Page 557: Reference
Reference This chapter provides reference information for camera features, system accessories, etc. Certification Logo Select [54: Certification Logo Display] and press <0> to display some of the logos of the camera’s certifications. Other certification logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.
Page 558: B Button Functions
B Button Functions When you press the button while the camera is ready to shoot, you can display [Displays camera settings], [Electronic level] (p.65), and [Displays shooting functions] (p.395). Under the [53] tab, [z button display options] enables you to select the options displayed when the ...
Page 559 B Button Functions Shooting Function Settings White balance correction Aperture AE lock Shutter speed Flash exposure compensation Shooting mode ISO speed Highlight tone priority Exposure level indicator Wi-Fi func ion Picture Style Custom Controls AF operation Image-recording quality Quick Control icon Possible shots Battery check Max.
Page 560: Checking The Battery Information
(Red) : Purchasing a new battery is recommended. The use of a genuine Canon Battery Pack LP-E6 is recommended. If you use batteries that are not genuine Canon products, the camera’s full performance may not be attained or malfunction may result.
Page 561 3 Checking the Battery Information Registering the Battery to the Camera You can register up to six LP-E6 battery packs to the camera. To register multiple battery packs to the camera, do the procedure below for each battery pack. Press the button. With the battery info.
Page 562 3 Checking the Battery Information Labeling the Serial Number on the Battery It is convenient to label all registered Battery Pack LP-E6 with their serial numbers, using commercially available labels. Write the serial number on a Serial number label. Write the serial number displayed on the battery history screen on a label approx.
Page 563 3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery Pack You can check the remaining capacity of any battery pack (even when not installed) and also when it was last used. Look for the serial number. Serial number Date last used Refer to the battery’s serial number label and look for the battery’s serial...
Page 564: Using A Household Power Outlet
Using a Household Power Outlet With AC Adapter Kit ACK-E6 (sold separately), you can connect the camera to a household power outlet and not worry about the remaining battery level. Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the AC Adapter’s socket.
Page 565: H Using Eye-Fi Cards
H Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card manufacturer.
Page 566 H Using Eye-Fi Cards Display the connection information. Select [Connection info.], then press <0>. Check the [Access point SSID:]. Check that an access point is displayed for [Access point SSID:]. You can also check the Eye-Fi card’s MAC address and firmware version. Press the <M>...
Page 567 H Using Eye-Fi Cards Cautions for Using Eye-Fi Cards If [53: Wi-Fi] is set to [Enable], image transfer with an Eye-Fi card is not possible. If “ ” is displayed, an error occurred while retrieving the card information. Turn he camera’s power switch off and on again. Even if [Eye-Fi trans.] is set to [Disable], it may still transmit a signal.
Page 568: Function Availability Table According To Shooting Mode
Function Availability Table According to Shooting Mode Still Photo Shooting o: Set automatically k: User selectable : Not selectable/Disabled Basic Zone Creative Zone Function A 7 C 2 3 4 5 6 F G d s f a F All image quality settings k k k k k k k k k k k k k k selectable...
Page 569 Function Availability Table According to Shooting Mode Basic Zone Creative Zone Function A 7 C 2 3 4 5 6 F G d s f a F o k k k k k AF-assist beam k k k k k AF Microadjustment k k k k k k k k k k k k k k k Continuous AF*...
Page 570: Movie Shooting
Function Availability Table According to Shooting Mode Movie Shooting o: Set automatically k: User selectable : Not selectable/Disabled Movie Still Photos A 7 C 8 d s f F Function M y k M All image quality settings k k k k k k k k k selectable (movie) All image quality settings k k k...
Page 571 Function Availability Table According to Shooting Mode Movie Still Photos A 7 C 8 d s f F Function M y k M k k k k k k k k k k k k u+Tracking k k k k k k k k k k k k FlexiZone - Multi k k k k k k k k k k k k FlexiZone - Single...
Page 572: Menu Settings
Menu Settings Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Page 1* / 41* / 61* Image quality 73/83/74/84/7a/8a/b/c VF grid display Disable / Enable Viewfinder level Hide / Show Beep Enable / Touch to / Disable Release shutter Enable / Disable without card Image review...
Page 573 Menu Settings z: Shooting 3 (Red) Page Exposure 1/3-stop increments, ±5 stops (AEB ±3 stops) compensation/AEB ISO speed / ISO speed range / Auto ISO range / ISO speed settings Minimum shutter speed Disable / Low / Standard / High Auto Lighting Optimizer OFF with M or Bulb...
Page 574 Menu Settings A1: Live View shooting 1 (Red) Page Live View shooting Enable / Disable u+Tracking / FlexiZone - Mul i / AF method FlexiZone - Single / Quick mode Continuous AF Enable / Disable Touch Shutter Enable / Disable Off / 3x3 l / 6x4 m / 3x3+diag n Grid display Aspect ratio...
Page 575 Menu Settings 3: Playback 2 (Blue) Page Resize Downsize the image’s pixel count [OFF] / l / m / n / o / p Rating Playback description / Display time / Repeat / Slide show Transition effect / Background music 1 image / 10 images / 100 images / Date / Image jump w/6 Folder / Movies / Stills / Rating...
Page 576 Menu Settings 5: Set-up 1 (Yellow) Page Select folder Create and select a folder File number Continuous / Auto reset / Manual reset Auto rotate OnzD / OnD / Off Format card Initialize and erase data on he card Displayed when a commercially-available Eye- Eye-Fi settings Fi card is inserted 5: Set-up 2 (Yellow)
Page 577 Menu Settings 5: Set-up 3 (Yellow) Page Video system NTSC / PAL Feature guide Enable / Disable Touch control Standard / Sensitive / Disable z Button display Displays camera settings / Electronic level / options Displays shooting functions Wi-Fi Disable / Enable Transfer images between cameras / Connect to smartphone / Remote control Wi-Fi function...
Page 578 Menu Settings 5: Set-up 4 (Yellow) Page Auto cleaning: Enable / Disable Sensor cleaning Clean now Clean manually Power / Remaining capacity / Shutter count / Battery info. Recharge performance / Battery registration / Battery history Certification Logo Displays some of the logos of the camera’s Display certifications Custom shooting mode...
Page 579 Menu Settings Movie Shooting Z1: Movie 1 (Red) Page u+Tracking / FlexiZone - Multi / AF method FlexiZone - Single Movie Servo AF Enable / Disable Silent LV shooting Mode 1 / Mode 2 / Disable 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / Metering timer 30 min.
Page 580: System Map
System Map Macro Ring Lite Macro Twin Lite ST-E2 ST-E3-RT 270EX II 320EX 430EX II 600EX-RT/ MR-14EX MT-24EX 600EX Bundled Accessories 90EX Eyecup Eb Eyepiece Extender EP-EX15 Rubber Frame Eb Wide Strap EW-EOS70D E-series Dioptric Adjustment Lenses Battery Pack Battery Charger LP-E6 LC-E6 or LC-E6E Angle Finder C...
Page 581 System Map Remote GPS Receiver Remote Controller GP-E2 Switch RC-6 RS-60E3 EF lenses EF-S lenses External microphone HDMI Cable HTC-100 (2 9 m/9.5 ft.) Stereo AV Cable AVC-DC400ST (1.3 m/4.3 ft.) TV/Video EOS DIGITAL Solution Disk PictBridge-compatible printer Interface Cable (1.3 m/4.3 ft.) Interface Cable IFC-200U/ FC-500U (1.9 m/6 2 ft /4.7 m/15.4 ft.)
Page 582: Troubleshooting Guide
The battery pack does not recharge. If the battery’s remaining capacity is 94% or higher, the battery will not be recharged (p.396). Do not recharge any battery pack other than genuine Canon Battery Pack LP-E6. The charger’s lamp blinks at high speed.
Page 583 Troubleshooting Guide The access lamp still blinks even when the power switch is set to <2>. If the power is turned off while an image is being recorded to the card, the access lamp will remain on or continue to blink for a few seconds. When the image recording is completed, the power will turn off automatically.
Page 584 Troubleshooting Guide Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-M lenses (p.40). The viewfinder is dark. Install a recharged battery pack in the camera (p.28). No images can be shot or recorded. Make sure the card is properly inserted (p.31). Slide the card’s write-protect switch to the write/erase position (p.31).
Page 585 Troubleshooting Guide The image is out of focus. Set the lens focus mode switch to <AF> (p.40). To prevent camera shake, press the shutter button gently (p.44, 45). If the lens has an Image Stabilizer, set the IS switch to <1>. In low light, the shutter speed may become slow.
Page 586 Troubleshooting Guide ISO 100 cannot be set. ISO speed expansion cannot be selected. When [z4: Highlight tone priority] is set to [Disable], ISO 100/125/ 160 can be set (p.145). If [z4: Highlight tone priority] is set to [Enable], the settable ISO speed range will be ISO 200 - ISO 12800 (or up to ISO 6400 for movie shooting).
Page 587 The external flash does not fire. If you use a non-Canon flash unit with Live View shooting, set [A2: Silent LV shoot.] to [Disable] (p.231). The external flash always fires at full output.
Page 588 Troubleshooting Guide The shutter makes two shooting sounds during Live View shooting. If you use flash, the shutter will make two sounds each time you shoot (p.217). During Live View and movie shooting, a white < > or red <E> icon is displayed. It indicates that the camera’s internal temperature is high.
Page 589 Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie when [Maximum: H (25600)] is set with [ISO speed range] and ISO speed is set to “H” (25600), the ISO speed will switch to “H”...
Page 590 Troubleshooting Guide Wi-Fi Wi-Fi cannot be set.* If the camera is connected to a printer, computer, GPS receiver, or other device with an interface cable, Wi-Fi cannot be set ([53: Wi-Fi] will be grayed out). Disconnect the interface cable, then set the Wi-Fi. For details, refer to the Wi-Fi Function Instruction Manual.
Page 591 Troubleshooting Guide Display Problems The menu screen shows few tabs and options. In Basic Zone modes, certain tabs and menu options are not displayed. Set the shooting mode to a Creative Zone mode (p.52). The file name’s first character is an underscore (“_”). Set the color space to sRGB.
Page 592 Troubleshooting Guide The LCD monitor does not display a clear image. If the LCD monitor is dirty, use a soft cloth to clean it. In low or high temperatures, the LCD monitor display may seem slow or may look black. It will return to normal at room temperature. [Eye-Fi settings] does not appear.
Page 593 Troubleshooting Guide When the movie is played back, camera operation noise can be heard. If you operate the camera’s dials or lens during movie shooting, the operation noise will also be recorded. Using an external microphone (commercially available) is recommended (p.269). The movie has still moments.
Page 594 Troubleshooting Guide I cannot process the RAW image. 41 and 61 images cannot be processed with the camera. Use the provided software Digital Photo Professional to process the image (p.456). I cannot resize the image. c JPEG images and 1/41/61 images cannot be resized with the camera (p.333).
Page 595 Troubleshooting Guide Computer Connection Problems I cannot transfer images to a personal computer. Install the provided software (EOS DIGITAL Solution Disk CD-ROM) on the computer (p.456). If [53: Wi-Fi] is set to [Enable], the camera cannot be connected to a computer.
Page 596: Error Codes
Communications between the camera and lens is faulty. Clean the lens contacts. Clean the electrical contacts on the camera and lens, use a Canon lens, or remove and install the battery pack again (p.19, 20, 30). Card cannot be accessed. Reinsert/change card or format card with camera.
Page 597: Specifications
* UHS-I cards compatible. Image sensor size: Approx. 22.5 x 15.0mm Compatible lenses: Canon EF lenses (including EF-S lenses) * Excluding EF-M lenses (35mm-equivalent focal length is approx. 1.6 times the lens focal length) Lens mount: Canon EF mount •...
Page 598 Specifications White balance: Auto, Preset (Daylight, Shade, Cloudy, Tungsten light, White fluorescent light, Flash), Custom, Color temperature setting (approx. 2500-10000 K), White balance correction, and White balance bracketing possible * Flash color temperature information transmission enabled Noise reduction: Applicable to long exposures and high ISO speed shots Automatic image Auto Lighting Optimizer brightness correction:...
Page 599 Specifications • Exposure Control Metering modes: 63-zone TTL full-aperture metering • Evaluative metering (linked to all AF points) • Partial metering (approx. 7.7% of viewfinder at center) • Spot metering (approx. 3.0% of viewfinder at center) • Center-weighted average metering Metering brightness EV 1 - 20 (at room temperature, ISO 100) range:...
Page 600 RAW: Approx. 15 shots (approx. 16 shots) RAW+JPEG Large/Fine: Approx. 8 shots (approx. 8 shots) * Figures are based on Canon’s testing standards (ISO 100 and Standard Picture Style) and an 8 GB card. * Figures in parentheses apply to an UHS-I compatible 8 GB card based on Canon’s testing standards.
Page 601 Specifications Continuous AF: Provided Focusing brightness EV 0-18 (at room temperature, ISO 100) range: Metering modes: Evaluative metering (315 zones), Partial metering (approx. 10.3% of Live View screen), Spot metering (approx. 2.6% of Live View screen), Center-weighted average metering Metering brightness EV 0 - 20 (at room temperature, ISO 100) range: Creative filters:...
Page 602 Specifications Exposure control: Autoexposure shooting (Program AE for movies) and manual exposure Exposure ±3 stops in 1/3-stop increments (±5 stops for still photos) compensation: ISO speed: For autoexposure shooting: 1. ISO 100 - ISO 6400 set (Recommended automatically. In Creative Zone modes, the upper limit is exposure index) expandable to H (equivalent to ISO 12800).
Page 603 Specifications Rating: Provided Movie playback: Enabled (LCD monitor, video/audio OUT, HDMI OUT), built-in speaker Slide show: All images, by date, by folder, by movies, by stills, by rating Background music: Selectable for slide shows and movie playback Image protect: Possible •...
Page 604 Specifications • Power Battery: Battery Pack LP-E6 (Quantity 1) * AC power can be supplied via AC Adapter Kit ACK-E6. * With Battery Grip BG-E14 attached, size-AA/LR6 batteries can be used. Battery information: Remaining capacity, Shutter count, Recharge performance, and Battery registration possible Number of possible With viewfinder shooting: shots:...
Page 605 Specifications Working temperature 5°C - 40°C / 41°F - 104°F range: Working humidity: 85% or less Dimensions (W x H x D): Approx. 69.0 x 33.0 x 93.0 mm / 1.5 x 0.8 x 3.7 in. Weight: Approx. 130g / 23.6 oz. •...
Page 606 EW-78D (sold separately) Case: LP1116 (sold separately) All the data above is based on Canon’s testing standards and CIPA (Camera & Imaging Products Association) testing standards and guidelines. Dimensions, maximum diameter, length and weight listed above are based on CIPA Guidelines (except weight for camera body only).
Page 607: Handling Precautions: Ef-S18-55Mm F/3.5-5.6 Is Stm, Ef-S18-135Mm F/3.5-5.6 Is Stm
Handling Precautions: EF-S18-55mm f/3.5-5.6 IS STM, EF-S18-135mm f/3.5-5.6 IS STM The kit lenses use a stepping motor that drives the focus lens. The motor controls the focus lens even during zooming. 1. When the camera is OFF The motor does not operate while the camera is OFF or when the camera is OFF due to the auto power off function.
Page 608 This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this...
Page 609: Safety Warnings
Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below: - Do not use any batteries, power sources, and accessories not specified in this booklet.
Page 610 • Before storing the camera or accessory when not in use, remove the battery pack and disconnect the power plug. This is to prevent electrical shock, heat generation, and fire. • Do not use the equipment where there is flammable gas. This is to prevent an explosion or fire.
Page 611 • Do not use paint thinner, benzene, or other organic solvents to clean the equipment. Doing so may cause fire or a health hazard. If the product does not work properly or requires repair, contact your dealer or your nearest Canon Service Center.
Page 612 If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Tel No. (516)328-5600 This Class B digital apparatus complies wi h Canadian ICES-003.
Page 613 4. Do not expose the charger to rain or snow. 5. Use of an attachment not recommended or sold by Canon may result in fire, electric shock, or personal injury. 6. To reduce risk of damage to electric plug and cord, pull by plug rather than by cord when disconnecting charger.
Page 614 MEMO...
Page 615: Viewing The Cd-Rom Instruction Manuals
Viewing the CD-ROM Instruction Manuals / Downloading Images to Your Computer This chapter explains how to install the Camera Instruction Manual CD-ROM to your computer, download images from the camera to your computer, gives an overview of the software in the EOS DIGITAL Solution Disk (CD-ROM), and explains how to install the software on your computer.
Page 616: Viewing The Camera Instruction Manual Cd-Rom
Viewing the Camera Instruction Manual CD-ROM The Camera Instruction Manual CD-ROM contains the following electronic manuals (PDF): Camera Instruction Manual Explains all the camera functions and procedures, including basic content. Wi-Fi Function Instruction Manual Explains all the Wi-Fi functions and procedures, including basic content.
Page 617 Select the language. EOS 70D (W) / EOS 70D (N) English Français Español © CANON NC 20 3 Click on the manual you want to view. EOS 70D (W) / EOS 70D (N) Camera Instruction Manual Wi Fi Function Instruction Manual...
Page 618: Downloading Images To A Computer
Downloading Images to a Computer You can use the provided software to download the images in the camera to your computer. There are two ways to do this. Downloading by Connecting the Camera to the Computer Install the software (p.458) Use the provided interface cable to connect the camera to your computer.
Page 619 Use ImageBrowser EX. For details, refer to the Software Instruction Manual on the CD-ROM (p.459). When downloading images from the camera to your computer, with a card reader without using Canon software, copy the DCIM folder on the card to your computer.
Page 620: Software Overview
Software Overview EOS DIGITAL Solution Disk This disk contains various software for EOS DIGITAL cameras. EOS Utility With the camera connected to a computer, EOS Utility enables you to transfer still photos and movies shot with the camera to the computer. You can also use this software to set various camera settings and shoot remotely with the computer connected to the camera.
Page 621 Software Overview Picture Style Editor You can edit Picture Styles and create and save original Picture Style files. This software is aimed at advanced users who are experienced in processing images.
Page 622: Installing The Software
Insert EOS DIGITAL Solution Disk (CD-ROM). For Macintosh, double-click to open the CD-ROM icon displayed on the desktop, then double-click on [Canon EOS Digital Installer]. When a screen to select where you live or a language appears, follow the on-screen instructions.
Page 623: Software Instruction Manual
Software Instruction Manual Contains the Software Instruction Manuals. Copying and Viewing the Software Instruction Manual PDFs Insert the [Software INSTRUCTION MANUAL] CD-ROM into your computer. Double-click the CD-ROM icon. For Windows, the icon is displayed in [(My) Computer]. For Macintosh, the icon is displayed on the desktop. Copy the [English] folder to your computer.
Page 624: Index
Index Numerics ALL-I (I-only) ........ 265 Ambience-based shots....92 10- or 2-sec. self-timer....113 Aperture-priority AE...... 162 1280x720 ........265 Art bold effect ....... 226, 337 1920x1080 ........265 Aspect ratio ........229 19-point AF auto selection ....103 Attenuator........268 4- or 9-image index display...296 Auto Lighting Optimizer....
Page 625 Index Holding the camera ....44 DC Coupler........400 Settings display ......394 Depth-of-field preview .. 163, 216, 221 Cards ......3, 19, 31, 57 Dials Card reminder......32 Main Dial ........46 Formatting ........57 Mode Dial......24, 46 Low-level formatting ....58 Quick Control Dial ...... 47 Problems ......33, 58 DIGITAL (USB) terminal ..
Page 626 Index File size......117, 266, 292 Filter effects ......131, 335 GPS..........412 Final image simulation ..221, 260 Grainy B/W......226, 336 Fine Grid display ....229, 276, 291 (image-recording quality) ..117, 118 Firmware version ......414 Handheld Night Scene ....87 First-curtain synchronization..200 HD ........
Page 627 Index Histogram display .....295 LCD panel ........22 Index.........296 Lens.......... 25, 40 Jump display Chromatic aberration (image browsing) ......297 correction ......... 147 Magnification ......298 Image stabilizer......43 Manual rotation......301 Instruction Manual... CD-ROM Numbering ........151 Lock release....... 41 Playback ........289 Peripheral illumina ion Protecting .........320 correction .........
Page 628 Movies ..........251 High ISO speed ....... 141 AE lock ........253 Long exposures ....... 143 AF method......263, 273 Nomenclature......... 20 Attenuator.........268 Non-Canon flash units....194 Autoexposure shooting.....252 Compression method ....265 Normal Drop frame .......272 (image-recording quality) ..117, 118 Editing ........310 NTSC ........
Page 629 Index Picture Style ....126, 129, 132 Recharging ........28 Pixels ..........116 Recording level......268 Playback ........289 Red-eye reduction ......190 Portrait ..........82 Reduced display......296 Possible shots......36, 217 Release shutter without card..32 Remote control shooting ....184 Power Auto power off ......59 Remote switch......
Page 630 Index 4 (Close-up)......84 Touch screen......54, 299 5 (Sports)......85 Touch Shutter ....... 245 6 (Night Portrait) ....86 Toy camera effect....227, 337 F (Handheld Night Scene) ..87 Tripod socket........21 G (HDR Backlight Control)..88 Tv (Shutter-priority AE) ....160 Shooting orientation registration ...373 Shutter button .........45 Shutter synchronization ....200 USB (DIGITAL) terminal..
Page 631 MEMO...
Page 632 The lenses and accessories mentioned in this Instruction Manual are current as of April 2013. For information on the camera’s compatibility with any lenses and accessories introduced after this date, contact any Canon Service Center. CPX-E059-000 © CANON INC. 2013...
Page 633: Quick Reference Guide
Number of Possible Shots (Viewfinder Shooting) Dial to < A > (Scene Temperature No Flash 50% Flash Use English CPQ-E059-000 © CANON INC. 2013 Intelligent Auto). At 23°C / 73°F Approx. 1300 shots Approx. 920 shots Preparation Image-recording Quality Q Quick Control Touch Screen Menu Operations Select [ z 1: Image quality], then press <...
Page 634: Shooting Operation
Shooting Operation Nomenclature LCD Panel Basic Zone Modes Creative Zone Modes All the settings necessary for You can change the camera ISO speed setting button Drive mode ISO speed <q> Metering mode shooting are set automatically. settings as desired to shoot in <R>...
Page 635 EOS 70D (W) Wi-Fi Function Basic Instruction Manual In this booklet, basic procedures for easy-to-use “Transferring Images between Cameras” and “Connecting to a smartphone” functions are explained. For detailed explanation about Wi-Fi functions, refer to “Wi-Fi Function Instruction Manual” included in the Camera Instruction Manual CD-ROM.
Page 636: What You Can Do Using The Wireless Lan Functions
(6) View images using smartphone a media player Make images View images viewable Remote shooting (Canon Image Gateway) (5) Send images to (3) Print images using a Web service a Wi-Fi printer Save and share images Print images (4) Operate the camera...
Page 637 EOS Utility. Send images to a Web service (CD-ROM) Upload your images to CANON iMAGE GATEWAY, an online photo service for Canon users (free registration required), to share them with family and friends. View images using a media player (CD-ROM) Display images on the camera’s memory card on your TV set, by...
Page 638 All o her corporate and product names and trademarks mentioned in this manual are the property of their respective owners. Note that Canon cannot be held liable for any loss or damage from erroneous wireless LAN settings for using the camera. In addition, Canon cannot be held...
Page 639 Contents Introduction What You Can Do Using the Wireless LAN Functions ..... 2 Conventions Used in This Manual ............ 4 Basic Settings for Wireless LAN Functions Registering a Nickname..............8 Basic Operation and Settings ............11 Transferring Images Between Cameras Selecting the Connection Destination ..........
Page 640 MEMO...
Page 641: Basic Settings For Wireless Lan Functions
Basic Settings for Wireless LAN Functions This chapter describes settings necessary for using the camera’s wireless LAN functions.
Page 642: Registering A Nickname
Registering a Nickname First, set the camera’s nickname. When the camera is connected to another device via a wireless LAN, the nickname will be displayed on the device. Be sure to set a nickname for your camera. Select [Wi-Fi]. Under the [53] tab, select [Wi-Fi], then press <0>.
Page 643 Registering a Nickname Enter a nickname. For instructions on entering characters, see “Virtual Keyboard Operation” on the next page. Up to 16 characters can be entered. Finish. When you are finished, press the <M> button. Select [OK] on the confirmation screen, then press <0>.
Page 644 Registering a Nickname Virtual Keyboard Operation Switching to other input areas To switch between top and bottom input areas, press the <Q> button. Moving the cursor To move the cursor, press the key in the top area. Entering text In the bottom input area, press the <V>...
Page 645: Basic Operation And Settings
Basic Operation and Settings Using the Camera While Wireless LAN Functions Are Active When you want to prioritize wireless LAN functions, do not operate the shutter button, Mode Dial, or playback button. Otherwise, shooting or playback operation may be prioritized and wireless LAN functions may be terminated during the process.
Page 646 Basic Operation and Settings [Wi-Fi] Settings and Connection Status Settings and connection status for [Wi-Fi] under the [53] tab can be checked on the camera’s LCD monitor and LCD panel. Wi-Fi function Wi-Fi func ion Wi-Fi connection status LCD monitor LCD panel Wi-Fi connection Wi-Fi function...
Page 647 Basic Operation and Settings Touch Control You can operate wireless LAN functions by touching the screen as well. For details, refer to “Using the Touch Screen” in the Camera Instruction Manual. Connecting with an Interface Cable When [53: Wi-Fi] is set to [Enable], interface cable connection is disabled.
Page 648 MEMO...
Page 649: Transferring Images Between Cameras
Wireless connection is possible for Canon cameras with built-in wireless LAN functions marketed in 2012 or later. Note that the camera cannot be connected to Canon camcorders, even if they have built-in wireless LAN functions. The camera cannot be connected to Canon cameras without built-in wireless LAN functions, even if they support Eye-Fi cards.
Page 650: Selecting The Connection Destination
Selecting the Connection Destination Register the target camera to connect to via a wireless LAN. The camera can be connected to only one camera at a time. Select [Wi-Fi function]. Under the [53] tab, set [Wi-Fi] to [Enable], then select [Wi-Fi function].
Page 651 Selecting the Connection Destination Select the images to send. Select images on the camera sending the images (p.18). Do not operate the camera receiving the images. Note that GPS information is not displayed on the camera’s playback screen even if GPS information is appended to the received image. Shooting locations can be viewed on a virtual map, using the Map Utility software.
Page 652: Sending Images
Sending Images Sending Images One by One Selected images are sent one by one. Select an image to send. Press the key to select an image to send, then press <0>. You can also press the button to select an image in the index display.
Page 653 Sending Images Sending Selected Images Multiple images can be selected and sent. Press <0>. Select [Send selected]. To select a size at which to send the images, select [Resize image] and press <0>. Press the key to select [Send selected], then press <0>.
Page 654 Sending Images Reduce the image size. Set it if necessary. Send the images. Press the <V> key to select [Send], then press <0> to send the images. The transfer progress screen is displayed. To transfer other images, repeat steps 1 to 5. Terminate connection.
Page 655: Reconnecting
Reconnecting The camera can reconnect to another camera for which connection settings have been registered. Select [Wi-Fi function]. Under the [53] tab, set [Wi-Fi] to [Enable], then select [Wi-Fi function]. Select [z]. Select [z] (Transfer imgs between cameras) and press <0>. Establish a connection.
Page 656 MEMO...
Page 657: Connecting To A Smartphone
Connecting to a Smartphone Connecting the camera to a smartphone lets you use the smartphone to view, manage, and receive images stored in the camera. You can also use the smartphone to perform remote shooting. Note that movie shooting is disabled.
Page 658: Preparation
Preparation EOS Remote Installation Required To communicate with a smartphone, the camera needs to be connected to the smartphone using the dedicated application EOS Remote. EOS Remote can be downloaded from the App Store or Google Play. Install EOS Remote on the smartphone and then perform the procedures to establish the connection.
Page 659: Using Camera Access Point Mode To Establish A Connection
Using Camera Access Point Mode to Establish a Connection The camera and smartphone can be directly connected via a wireless LAN. Because the camera acts as an access point, no other access point is necessary, so you can establish communications easily even when you are out.
Page 660 Using Camera Access Point Mode to Establish a Connection Connect the smartphone to the camera. On the Wi-Fi settings menu of the smartphone, select the SSID (network name) displayed on the camera’s LCD monitor. For the password, enter the encryption key displayed on the camera’s LCD monitor.
Page 661 Using Camera Access Point Mode to Establish a Connection Connect to the camera. When pairing is completed, the screen on the left is displayed. Press the key to select [OK], then press <0>. Non-ASCII characters are displayed as 8. Perform further settings.
Page 662: Operating The Camera Using A Smartphone
Operating the Camera Using a Smartphone You can use a smartphone with EOS Remote installed to view images stored in the camera and shoot remotely. EOS Remote Main Screen The main functions of EOS Remote are described below. Touch the screen to learn the operation procedures.
Page 663 Operating the Camera Using a Smartphone Terminating the Connection Select [Exit]. If the screen on the left is not displayed, select [Wi-Fi function] under the [53] tab. Select [Exit] and press <0>. Select [OK]. Press the key to select [OK], then press <0>...
Page 664: Reconnecting
Reconnecting The camera can reconnect to a smartphone for which connection settings have been registered. Select [Wi-Fi function]. Under the [53] tab, set [Wi-Fi] to [Enable], then select [Wi-Fi function]. Select [q]. Select [q] (Connect to smartphone) and press <0>. Establish a connection.
Page 665 CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. http://www.usa.canon.com/eos http://www.usa.canon.com/support For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7, Canada CANON CANADA INC.

This manual is also suitable for:

Eos 70d(w)

Canon EOS 70DN Basic Instruction Manual

Table of Contents

Introduction

Getting Started

Basic Shooting

Setting the AF and Drive Modes

Image Settings

Advanced Operations

Shooting with the LCD Monitor

(Live View Shooting)

Shooting Movies

Image Playback

Viewing the CD-ROM Instruction Manuals

Downloading Images to Your Computer

Table of Contents

Chapters

Getting Started

Basic Shooting

Setting the AF and Drive Modes

Image Settings

Advanced Operations

Flash Photography

Shooting with the LCD Monitor

(Live View Shooting)

Shooting Movies

Image Playback

Post-Processing Images

Sensor Cleaning

Printing Images

12

Customizing the Camera

13

Reference

Viewing the CD-ROM Instruction Manuals

Downloading Images to Your Computer

Quick Links

Chapters

Related Manuals for Canon EOS 70DN

Summary of Contents for Canon EOS 70DN