Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
FOR PC-BVBN (02285)
NATURAL GAS TO PROPANE/LP GAS
For Use When Converting Models SBVBN(A) or CBVBN(A)
This conversion kit must be installed by a qualified service agency.
Read these instructions completely before installing this conversion kit.
Before proceeding, make sure the gas control valve is in the "OFF" position, all electrical
power to the appliance is OFF, and the fireplace is cool to the touch.
CAUTION: The gas supply shall be shut off prior to disconnecting the
electrical power before proceeding with the conversion.
Parts included with this kit:
Part No.
Description
Instruction Sheet
105798-04
Pilot Orifice, Propane/LP
105523-02
Burner, Propane/LP
104506-04
Main Burner Orifice (1.39mm)
105799-02
Gas Valve Regulator
105801-02
Conversion Label, English
106038-02
Conversion Label, French
106080-01
Conversion Information Label
Tools Required
• 10mm Open End Wrench
• 5/16" Socket or Nut Driver
• 18mm Open End Wrench or
Adjustable Wrench
• 3/4" Open End Wrench or
Adjustable Wrench
• 7/8" Open End Wrench or
Channel Lock Pliers
If any of these pieces are missing or damaged, contact the dealer where you purchased this
kit or DESA International at 1-800-972-7879 for referral information.
INTERNATIONAL
CONVERSION KIT
• 3/8" Socket, Nut Driver or
Slotted Screwdriver
• #2 Phillips Screwdriver
• 7/16" Open End Wrench
• Needle Nose Pliers
• High Temperature Silicone Sealant
(GE RTV 106/Loctite RTV 81585)
• Thread Sealant (Resistant to Propane/LP)
REMOVING GLASS DOOR
The glass door must be removed to allow
access inside the firebox chamber for con-
version. To remove the glass door, the front
panel on the stove body must be removed.
1.
To remove the stove front panel, re-
move two 10mm hex bolts from bot-
tom of stove and one phillips head bolt
from top of stove (see Figure 1).
2.
Using a 3/8" socket or slotted screw-
driver remove the screws from the two
Quantity
tabs at the top of the glass door (see
1
Figure 2, page 2). Hold glass door se-
1
curely to keep it from falling forward.
1
3.
Grasp door by both sides and ease it
1
upward off the lower bracket (see Fig-
1
ure 2, page 2).
1
1
1
Stove Front Panel
Figure 1 - Removing Stove Front Panel
Bolt (Phillips
Head)
Bolt (10mm Hex)
Note: Appearance of
Stove Body may vary
depending on Model
Advertisement
Related Manuals for Desa PC-BVBN
Summary of Contents for Desa PC-BVBN
-
Page 1: Installation Instructions
Channel Lock Pliers • Thread Sealant (Resistant to Propane/LP) If any of these pieces are missing or damaged, contact the dealer where you purchased this kit or DESA International at 1-800-972-7879 for referral information. Bolt (10mm Hex) Note: Appearance of... - Page 2 PC-BVBN (02285) Conversion Kit Screw (3/8" Hex or Slotted Screwdriver) LOG REMOVAL 5. Remove the burner by loosening the two 5/16" hex mounting screws (see Carefully remove the log set and ember Figure 4). Lift burner up and out. material from around the burner and place Convert the pilot burner by changing out them outside the combustion chamber.
- Page 3 INSTALLATION INSTRUCTIONS French This 9. Replace pilot target removed in step 6, 4. Place rubber gasket supplied with regu- English This Side page 2. Tighten pilot target hex fitting lator kit on gas control valve. Align two Side until the pilot target aligns with the ther- of the holes on the gasket with orienta- mocouple and thermopile (see Figure 8).
-
Page 4: Final Preparation
FINAL PREPARATION WARNING: This conversion WARNING: Test all gas pip- 1. Replace logs and embers back into the kit shall be installed by a quali- ing and connections for leaks correct positions as instructed in your fied service agency in accordance after installing or servicing.