Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
FOR PC-BDV37N (02267)
NATURAL GAS TO PROPANE/LP GAS
For Use When Converting Models BDV37N Series
This conversion kit must be installed by a qualified service agency.
Read these instructions completely before installing this conversion kit.
Before proceeding, make sure the gas control valve is in the "OFF" position, all electrical
power to the appliance is OFF, and the fireplace is cool to the touch.
CAUTION: The gas supply shall be shut off prior to disconnecting the
electrical power before proceeding with the conversion.
Parts included with this kit:
Part No.
Description
Instruction Sheet
106040-02
Pilot Orifice
104504-02
Burner, Propane/LP
104506-02
Main Burner Orifice (1.32mm)
105838-02
Gas Valve Regulator
105801-09
Conversion Label, English
106038-09
Conversion Label, French
106080-01
Conversion Information Label
Tools Required
• 10mm Open End Wrench
• 12mm Open End Wrench
• 5/16" Socket or Nut Driver
• 18mm Open End Wrench or
Adjustable Wrench
• 3/4" Open End Wrench or
Adjustable Wrench
• 7/8" Open End Wrench or
Channel Lock Pliers
If any of these pieces are missing or damaged, contact the dealer where you purchased this
kit or DESA International at 1-800-972-7879 for referral information.
INTERNATIONAL
CONVERSION KIT
• Torx T20 or Slotted Screwdriver
• 3/8" Socket or Nut Driver or
Slotted Screwdriver
• #2 Phillips Screwdriver
• High Temperature Silicone Sealant
(GE RTV 106/Loctite RTV 81585)
• Thread Sealant (Resistant to Propane/LP)
REMOVING GLASS DOOR
1.
Remove the upper louver panel by lift-
ing upward and out (see Figure 1).
2.
Using a 3/8" socket or slotted screw-
driver remove the screws from the three
tabs at the top of the glass door (see
Figure 2, page 2). Hold glass door se-
curely to keep it from falling forward.
3.
Grasp door by both sides and ease it
upward off the lower bracket (see Fig-
ure 2, page 2).
Quantity
1
1
1
1
1
1
1
1
Figure 1 - Removing Top Louver Panel
Top Louver Panel
Advertisement
Related Manuals for Desa PC-BDV37N
Summary of Contents for Desa PC-BDV37N
-
Page 1: Installation Instructions
INTERNATIONAL INSTALLATION INSTRUCTIONS FOR PC-BDV37N (02267) CONVERSION KIT NATURAL GAS TO PROPANE/LP GAS For Use When Converting Models BDV37N Series REMOVING GLASS DOOR This conversion kit must be installed by a qualified service agency. Remove the upper louver panel by lift- Read these instructions completely before installing this conversion kit. - Page 2 PC-BDV37N (02267) Conversion Kit Screw Turn brass elbow and main burner ori- Replace original burner with burner fice counterclockwise to remove from supplied with kit. Attach with the two Glass Door burner. The orifice is threaded into the 5/16" hex mounting screws removed in Assembly burner inlet.
- Page 3 INSTALLATION INSTRUCTIONS GAS CONTROL VALVE CONVERSION LABELING French This English This Side CONVERSION AND PLACEMENT Side 1. Apply the English and French conver- Convert the gas control valve by swapping sion labels over the top of the existing out the valve regulator portion of the gas certification labels (see Figure 8).
- Page 4 FINAL PREPARATION WARNING: This conversion 1. Replace logs and embers back into the kit shall be installed by a quali- correct positions as instructed in your fied service agency in accordance appliance Owner’s Manual. with the manufacturer’s instruc- 2. Reinstall glass door and upper louver tions and all applicable codes panel on fireplace.