Wireless Programming; Assigning Wireless Zone Transmitters; Assigning Wireless Doorbells To The Console; Deleting Assigned Wireless Transmitters - Paradox Magellan MG-6060 Reference And Installation Manual

The Magellan system supports up to 16 wireless zones and two
wireless doorbells. These wireless zones are monitored using
transmitters such as wireless detectors and door contacts. The
Magellan console only supports the Paradox Magellan series of
wireless transmitters. The programming of the transmitters is
accomplished in two steps:
1. Assign the wireless transmitter to Magellan.
2. Program the wireless zone.

Assigning Wireless Zone Transmitters

Sections [021] to [036]: Zones 1-16; Wireless Transmitters 1-16
Sections [021] to [036] represent zones 1 to 16. A wireless
transmitter assigned to a section ([021] to [036]) will be assigned
to the zone represented by the section.
For example, a wireless transmitter assigned to section [025] will
be assigned to zone 5.
To assign a wireless transmitter:
1. Access the installer programming mode (see page 12).
2. Enter the [ ] corresponding to the desired zone.
SECTION
3. Enter the 6-digit [
SERIAL NUMBER
The serial number is located on the inside of the wireless
transmitter.
The wireless transmitters must be activated once having been
assigned to the Magellan console. To activate a transmitter,
insert the batteries and close the cover. To ensure proper
synchronization between the console and the transmitter, open
and close the zone corresponding to the transmitter.
Are the zones that have wireless transmitters assigned to them
programmed? See Zone Definitions on page 14 and Zone
Options on page 16.
Wireless transmitters can also be assigned through the Installer
MENU
menu. Press [ ] + [4] + [
zone you wish to assign the transmitter to, press [
cover of the transmitter and then close the cover. The
transmitter has been assigned. Refer to the Magellan Quick
Setup on page 4 for more information on the Installer menu and
the assignment of the wireless transmitters.

Assigning Wireless Doorbells to the Console

Sections [058] and [059]: Wireless Doorbells 1 and 2
Magellan supports the use of two wireless doorbells. By
connecting a pushbutton to the Universal Transmitter inputs of a
Magellan Wireless Door Contact (MG-DCT1), the MG-DCT1 will
transmit a signal to Magellan whenever the pushbutton is
pressed. Magellan will in turn become a doorbell and play a
predetermined tone (see Wireless Doorbell Tones on page 18).
Please refer to the appropriate Magellan Wireless Door
Contact Instruction for information on the installation and
configuration of the wireless door contact.
To assign a wireless doorbell:
1. Access the installer programming mode (see page 12).
2. Enter the [ ] corresponding to the desired doorbell.
SECTION
18

Wireless Programming

] of the wireless transmitter.
] + [6]. Select the
INSTALLER CODE
OK
], open the
3. Enter the 6-digit [
SERIAL NUMBER
Wireless Doorbell Tones
Section [096]: Options [1] to [4]
Options [1] and [2] = Set tone for wireless doorbell 1
Options [3] and [4] = Set tone for wireless doorbell 2
Section [096] options [1] to [4] set the tones that will be played
when Magellan receives a signal from either wireless doorbell 1
or 2 or both. Magellan comes with four tones. Refer to Table 3 on
page 18 to set the desired tone.
Table 3: Wireless Doorbell Tones
Section [096] - Options [1] and [2]
Option [1] OFF / Option [2] OFF (Doorbell 1)
Option [1] OFF / Option [2] ON (Doorbell 1)
Option [1] ON / Option [2] OFF (Doorbell 1)
Option [1] ON / Option [2] ON (Doorbell 1)
Section [096] - Options [3] and [4]
Option [3] OFF / Option [4] OFF (Doorbell 2)
Option [3] OFF / Option [4] ON (Doorbell 2)
Option [3] ON / Option [4] OFF (Doorbell 2)
Option [3] ON / Option [4] ON (Doorbell 2)

Deleting Assigned Wireless Transmitters

Sections [021] to [036]: Zones 1-16; Wireless Transmitters 1-16
Sections [058] and [059]: Wireless Doorbells 1 and 2
To delete an assigned wireless transmitter:
1. Access the installer programming mode (see page 12).
2. Enter the [ SECTION ] corresponding to the desired zone or
doorbell.
3. Press the [0] key six times to clear the wireless transmitter's
serial number.
Viewing Wireless Transmitter Signal
Strength
Sections [021] to [036]: Zones 1-16; Wireless Transmitters 1-16
Once wireless transmitters have been assigned to the Magellan
console, the signal strength of each transmitter can be verified in
sections [021] to [036] (zones 1 to 16 respectively). Each section
represents the signal strength viewer for the wireless transmitter
assigned to the corresponding zone.
For example, section [021] is the viewer for the wireless
transmitter assigned to zone 1 and section [036] is the viewer for
the wireless transmitter assigned to zone 16.
The signal strength is displayed using two terms:
• "Good": This is an average reading and is acceptable.
] of the MG-DCT1.
Doorbell Tone #
Tone 1 (default)
Tone 2
Tone 3
Tone 4
Doorbell Tone #
Tone 1
Tone 2 (default)
Tone 3
Tone 4
Reference & Installation Manual