Wireless Features; Wireless Transmitter Programming; Viewing The Wireless Transmitter Signal Strength; Supervision Options - Paradox Magellan MG5050 EN Reference & Installation Manual

The control panel(s) allows for the addition of up to thirty-two fully supervised wireless transmitters, and up to thirty-two programmable
remote controls.
9.1

Wireless Transmitter Programming

The programming of the wireless transmitters (detectors and door contacts) is accomplished in two steps:
1. Assign the wireless transmitter to the control panel.
2. Program the zones.
Wireless Transmitter Programming can be executed through the Installer Quick Menu in the programming guide.
Sections [061] to [092] represent expansion inputs 1 to 32 respectively.
The serial number is located on the inside of the transmitter or you can use the Serial Number Display (section [960]) to
determine its serial number. The transmitters must be activated once having been assigned to the control panel. To
activate a transmitter, insert the batteries and close the cover. To ensure proper synchronization between the control panel
and the transmitter, open and close the zone corresponding to the transmitter.
How Do I Assign Wireless Transmitters to the Panel?
1) Press the [
ENTER
2) Enter your [
3) Enter the desired [
4) Enter the 6-digit [
How Do I Delete Assigned Wireless Transmitters?
1) Press the [
ENTER
2) Enter your [
3) Enter the desired [
4) Press the [0] key six times to clear the serial number.
9.2

Viewing the Wireless Transmitter Signal Strength

Sections [101] to [132]
Once wireless transmitters have been installed and assigned to the control panel, the signal strength of each transmitter can be
verified in sections [101] to [132]. Each section represents the signal strength viewer for a specific device. For example, section
[101] is the viewer for zone 1 and section [132] is the viewer for the zone 32. Sometimes moving the transmitter or control panel
by a small amount will greatly increase the signal reception.
How Do I View a Wireless Transmitter's Signal Strength?
1) Press the [
ENTER
2) Enter your [
3) Enter the desired [
4) Press the transmitter's anti-tamper switch or open the corresponding zone.
5) The keypad will illuminate numbers 1 to 10.
Signal Strength Indicator
9.3

Supervision Options

The Supervision Options cannot be used with any remote controls assigned to the control panel.
9.3.1 Supervision Bypass Options
Section [705]: Arming/Disarming Options
Option [8] ON
Option [8] OFF
When this feature is disabled, the Wireless Transmitter Supervision Options will follow the zone's bypass definition.
This means the control panel will not perform any action if a Supervision Loss occurs on a bypassed zone. When this
feature is enabled, the Wireless Transmitter Options will ignore the bypass definition. This means the control panel will
generate an incident as per Wireless Transmitter Supervision Options if a supervision loss occurs on a bypassed zone.
32
Reference & Installation Manual
Part 9: Wireless Features
] key.
] (default: 0000 / 000000) or [
INSTALLER CODE
] (from sections [061] to [092]).
SECTION NUMBER
] of the wireless transmitter.
SERIAL NUMBER
] key.
] (default: 0000 / 000000) or [
INSTALLER CODE
] (from sections [061] to [092]).
SECTION NUMBER
] key.
] (default: 0000 / 000000) or [
INSTALLER CODE
] (from sections [101] to [132]).
SECTION NUMBER
8 to 10 / 3 beeps = Best signal
= Generate Supervision Loss if detected on a Bypassed Wireless Transmitter Zone
(default)
= No Supervision Loss if detected on a Bypassed Wireless Transmitter Zone
] (empty by default)
MAINTENANCE CODE
] (empty by default)
MAINTENANCE CODE
] (empty by default)
MAINTENANCE CODE
5 to 7 / 2 beeps = Average signal 1 to 4 / 1 beep = Weak signal (Relocate)