Table of Contents
Advertisement
- STEP 3: INSTALL FAUCET (cont.)-
B. ASSEMBLE
FAUCET
1. If not already
assembled,
install
the rubber
washer,
spacer,
flat (or lock)
washer
and
hex nut
onto
the
threaded
faucet
stud.
2. Apply
Teflon
tape
to the end
of the faucet
stud.
Turn the tubing
adapter
with
a blue
collet onto
the
stud
and hand
tighten,
then
wrench
1/4
turn
only.
BE CAREFUL
NOT TO CROSS
THREAD.
3. Wet the o-ring
seals
on the faucet
spout.
Then, re-
move
and discard
the short
piece of tubing
from the
faucet
body
and insert
the spout
in its place.
4. CONNECT
TUBING
TO FAUCET
AS FOLLOWS.
a. Take the separate
length
of 3 / 8" black tubing
put
an end through
the larger
hole in the rubber
wash-
er. Slide the end onto the larger
barb fitting
on the
bottom
of the faucet.
Note: To soften end of tubing,
hold under hot water.
b. Route
1/4"
red tubing
from
RO up through
the
sink hole and slide end onto the smaller
barb fitting
(heat end if needed)
on the faucet.
c. Route
3/8" blue
tubing
from
RO up through
the
sink hole and push
end all the way into the tubing
adapter
fitting
on the bottom
of the faucet.
Pull on
the tubing
to be sure it's held
firmly
in the adapter
fitting.
See pages
12 and 13 for tubing
connection
instructions.
FIG. 6 ]
insert spou_
remove tub-
ing piece
ASSEMBLED IN
MOUNTING
HOLE
rubber
washer
_
=_,=_/spacer
°ek
_.,_
hex nut
_._
tubing adapter
putty
blue collet
5. Lower
the faucet
into the sink or countertop
hole.
6. On the underside
of the sink or countertop,
insert
the large
steel
washer
between
the mounting
hole
and
the
spacer
on the faucet
stud
(see assembled
view).
Then,
turn
the hex nut
up to the spacer
and
tighten.
Tighten
the hex nut so the faucet
cannot
move,
but do not overtighten
and break
the faucet.
- STEP 4: INSTALL RO
ASSEMBLY -
Hang
the assembly
on the included
hanger
washers,
or lay on the cabinet
floor, as desired.
1. Refer to FIG. 7 for wall mounting.
Hold the assem-
bly up to the wall surface
and mark locations
for the
hanger
washers.
Indicator
marks
on top of the brack-
et are the needed
10-1/2"
apart.
2. Install
hanger
washers
at least 15-1/2"
up from the
cabinet
floor, allowing
room
to remove
sumps
from
filter
heads.
Wood
screws
are provided,
or obtain
other
fasteners
as needed.
steelwasher
.J
I
_
holein sink or
_
_1-[
countertop
114" red tubing
to drain point
_-_-//
\
\/
/_
YJ
3/8"blue /
TUBING FROM
tubing
RO SYSTEM
FIG. 7 ]
hanger
I'_,_
washer (2)
I_
screw (2) _(_)
10-1/2"
15-1/2"
min.
up from
floor
7
Hide quick links:
Advertisement
Table of Contents
