Panasonic KX-FC379CX Service Manual page 58

Code Function
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
710 Memory clear except History data
717 Transmit speed selection
718 Receive speed selection
722 Redial tone detect
731 CPC mode
732 AUTO disconnect cancel time
745 Power ON film feed
763 CNG detect time for friendly
reception
771 T1 timer
774 T4 timer
775 Monitoring of message transfer
784 Voice prompt test
815 Sensor & Vox check
841 Digital SP-phone check
852 Print test pattern
853 Top margin
874 DTMF ON time
875 DTMF OFF time
880 History list
881 Journal 2 list
882 Journal 3 list
958 Cordless test
Set Value Effective Default
Range
1:detects at 1, 2
the 1st time
2:detects at
the 2st time
X Number of 001~999
times
X dBm - 15~00
43= -43 dBm 20~48
1:14400BPS 1~6
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:14400BPS 1~6
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1:ON 2:OFF 1, 2
1:A 2:B 3:OFF 1~3
1:350 ms 1~3
2:1.8 sec
3:OFF
1:ON 2:OFF 1, 2
1:10 sec 1~3
2:20 sec
3:30 sec
1:60 sec 1, 2
2:90 sec
X 100 msec 00~99
1:ON 2:OFF 1, 2
1~9
X msec 060~200
X msec 060~200
57
1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot either transmit/receive long distance or
international communications (P.102). Refer to
Sometime There is a Transmit Problem(P.99) and
The unit can copy, but cannot either
transmit/receive long distance or international
communications (P.102).
100 Sets the number of acceptable error lines when the
FAX reconstructs the received data. Refer to Receive
Problem(P.100).
10 Selects the FAX transmission level. Refer to
Sometime There is a Transmit Problem (P.99)and
Receive Problem (P.100).
40 Used when there is an error problem. Refer to The
unit can copy, but cannot either transmit/receive
long distance or international
communications(P.102).
To reset the value to the default one, except History
data. Please restart a power supply after clearing a
memory.
1 Adjusts the speed to start training during FAX
transmission. Refer to Sometime There is a
Transmit Problem (P.99)and The unit can copy, but
the transmission and reception image are
incorrect(P.104).
1 Adjusts the speed to start training during FAX
reception. Refer to Receive Problem(P.100) and The
unit can copy, but the transmission and reception
image are incorrect (P.104).
2 Sets the tone detection mode after redialing.
1 Sets the CPC signal detection mode from the
converter.
1 "Set to "2" when the auto disconnect circuit operates
and cuts the line."
1 When the power is turned on, the film is wound to
take up any slack.
3 Selects the CNG detection tone of friendly reception.
1 Sets a higher value when the response from the other
party needs more time during FAX transmission.
Effective only at the time of automatic transmission. It
takes 35 seconds to transmit manually.
0 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
2 If set to ON a message can be monitored from this
unit´s SP-PHONE when transferring a message.
You can hear the voice prompt from speaker after
pressing "START" key.
See TEST FUNCTIONS(P.58).
See Digital Speakerphone(P.129).
See TEST FUNCTIONS (P.58).
5
180
090
See History (P.79).
See Printout Example (P.117).
See Printout Example (P.117).
See TEST FUNCTIONS (P.58).
KX-FC379CX
Remarks
----------
----------
----------