Note For Printed Wiring Board And Schematic Diagrams - Sony MZ-N510CK Service Manual

MZ-N510CK
6-2.

Note For Printed Wiring Board And Schematic Diagrams

Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from
(Side A) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Side B) the parts face are indicated.
• MAIN board is four-layer printed board.
However, the patterns of layers 2 and 3 have not been
included in this diagrams.
* Replacement of IC501,IC801 on MAIN board requires a
special tool.
• Lead Layouts
surface
Lead layout of conventional IC CSP (chip size package)
When IC852 is damaged, replace the MAIN board.
• Abbreviation
CND : Canadian model
MX : Mexican model
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 / W or less unless otherwise
4
specified.
• % : indicates tolerance.
• : internal component.
f
• C : panel designation.
Note: Note:
The components identi- Les composants identifiés par
fied by mark 0 or dotted une marque 0 sont critiques
line with mark 0 are criti- pour la sécurité.
cal for safety. Ne les remplacer que par une
Replace only with part piéce portant le numéro
number specified. spécifié.
• A : B+ Line.
• Total current is measured with MD installed.
• Power voltage is dc 3 V and fed with regulated dc power
supply from DC IN 3 V jack (J951).
• Voltages and waveforms are dc with respect to ground in
playback mode.
no mark : PLAYBACK
( ) : REC
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : PLAYBACK
c : DIGITAL IN
F : ANALOG IN
f : RECORD
N : USB
• The voltage and waveform of CSP (chip size package)
cannot be measured, because its lead layout is different
form that of conventional IC.
* Replacement of IC501,IC801 on MAIN board requires a
special tool.
When IC852 is damaged, replace the MAIN board.
• Waveforms
1 4
IC501 9 (RFO)(TP1517) IC601 4 (CLK)
1.2Vp-p
500mV/DIV, 200ns/DIV 1V/DIV, 2 µ s/DIV
2 5
IC501 rd (TE)(SL501) IC801 2 (OSCO)
(at the point of R806)
580mVp-p
500mV/DIV, 1ms/DIV 500mV/DIV, 20ns/DIV
3 6
IC501 rs (FE)(SL502) IC801 <z,/ (UOSCO)
(USB mode)
(at the point of R823)
240mVp-p
200mV/DIV, 1ms/DIV 1V/DIV, 10ns/DIV
40 40
7 0
IC901 yd (CLK) IC302 qs (LRCK)
2.5Vp-p 2.5Vp-p
(REC mode)
5.67 µ s 5.67 µ s
1V/DIV, 2 µ s/DIV 1V/DIV, 10 µ s/DIV
8
IC302 qa (MCLK)
44.3ns
2Vp-p
88.6ns
2.6Vp-p
1V/DIV, 40ns/DIV
9
IC302 0 (BCLK)
(REC mode)
2.6Vp-p
354ns
20.8ns 3.2Vp-p
1V/DIV, 100ns/DIV
22.7 µ s 2.4Vp-p