Related Manuals for Kenmore 146.1613211
Summary of Contents for Kenmore 146.1613211
- Page 1 Use & Care Guide Manual de Uso y Cuidado English / Espafiol Models/Modelos: 146.16132110/146.16133110 I(enmore ??ril prop_ I° 40200104 Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A. www.kenmore.com www.sears.com...
- Page 2 If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. 4. If odor continues, keep away appliance and immediately call your supplier or your fire department. 1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity this or any other appliance.
-
Page 3: Kenmore Grill Warranty
For Your Safety ... Grill Service Center... Product Record Information ... Installation Safety Precautions ... Safety Symbols ... Kenmore Grill Warranty... Use and Care. Parts List... Parts Diagram... Before Assembly ... Assembly... Troubleshooting... Repair Protection Agreements Congratulations on making a smart purchase. Your new I{enmore _) product is designed and manufactured for years of dependable operation. - Page 4 ° NEVER store a spare LP cylinder appliance or in an enclosed area. ° Never fill a cylinder beyond 80% full. • If the information in the two points above followed exactly, a fire causing death or serious injury may occur. •...
- Page 5 LP Tank Exchange • Many retailers that seii griiis offer you the option of replacing your empty LPtank through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their cylinders. Exchange your tank only for an OPD safety feature-equipped tank as described in the "LPTank"...
- Page 6 Hold coupling nut and regulator as shown for proper connection to LP tank valve. 6. Turn the coupling nut clockwise and tighten to a fuII stop. The regulator wilI seat on the back-check valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection.
- Page 7 • Apartment Dwellers. Check with management to learn the requirements and fire codes for using an LP gas grill in your apartment complex. If allowed, ground floor with a three (3)foot clearance walls or rails. Do not use on or under balconies.
- Page 8 Turn controls and gas source or tank OFF when not in use. CAUTION If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with The valve open, gas will contiune to flow out of the burner and could accidently ignite with risk of injury...
-
Page 9: Spider Alert
SPIDER ALERT! IMPORTANT: Always ensure that the venturi burner tubes are clean. A venturi burner tube has a narrow area in which spiders tend to build nests. If you notice that your grill is getting hard to light or that the flame isn't as strong as it should be, take the time to check and clean the venturi's. - Page 10 Indirect Cooking Poultry and large cuts of meat cook slowly to perfection on the grill by indirect heat. Place food over unlit burner(s); the heat from tit burners circulates gently throughout the grill, cooking meat or poultry without the touch of a direct flame. This method greatly reduces flare-ups when cooking extra fatty cuts because there is no direct flame to ignite the fats and juices that drip during cooking.
- Page 11 Sideburner Lid Rotate Rod, Sideburner Lid Sideburner Grid Sideburner Ignitor Wire, Sideburner Sideburner Base Right Side Shelf Fascia, RightSide Shelf Electronic Ignition Module Control Knob Impulse Control Line Gas Valve, Main Burner Gas Valve, Searing Burner Gas Valve, Sideburner Manifold, Sideburner Sideburner Hose Manifold, Main Burner Bezel, Control Knob...
- Page 12 12 _ 1613_.4200104...
- Page 13 READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTS FROM SHIPPING BOX. Step 1: Once you open the top of the shipping box, slice down its four edges with a box cutter. Take out the Hardware Pack, two grill side panels, back panel and bottom shelf. Next remove the door bracket, back rail and warming rack.
- Page 14 Step 2. With the aid of an assistant, turn grill head over on its side as shown in the first figure below, and remove the top styrofoam piece. Lay the styrofoam piece flat on the floor. With the aid of an assistant, lift the grill head out of the bottom styrofoam piece.
- Page 15 Step 3. Open grill lid, and take out the small boxes packed within the grill head. Remove all packing materials, and remove all parts from boxes as shown in the figures below. if!if: _ 16132-40200104 * 15...
- Page 16 CAREFULLY READ AND PERFORM ALL ASSEMBLY iNSTRUCTiONS Tools Required: • Adjustable wrench (not provided) • Screwdriver (not provided) • 7/16" Combination • The following hardware M4XIO screw Qty: 20 pcs M5XIO screw Qty: 4 pcs M6X13 screw Qty: 16 pcs M6 flat washer(Dia 12) Qty: 16 pcs 16 * 16132-40200104...
- Page 17 MBX15 screw QW: i6 pcs M6 lock washer M4XIO screw Qt¥:2 pcs 16132-4020010...
- Page 18 Cart To attach side panels, align side panel leg holes with leg holes on each side of bottom shelf. Left side panel has match holder attachment. Attach left and right side panels to sides of bottom shelf with (4) M6x13 screws, M6 lock washers and M6 flat washers (Dia 16).
- Page 19 Front Doors Remove the (4) M4xlO screws pre-assembled to the door handle ends, and use them to attach handles to doors. Insert the lower door pin into the hole on the bottom shelf. Pushdown the upper door pin, align it beneath hole in door pin bracket, and release pin so that it inserts in hole. Repeat this for the other door.
- Page 20 Grill Head to Cart This step requires two people to lift and position grill head onto cart. Remove the tie wraps securing regulator hose to underside of grill head. Pull hose and igniter wires out to side of grill head. Carefully lower the grill head onto the cart.
- Page 21 Left Side Shelf Slide 4 hooks onto push bar in orientation shown below. (A). Hook ends must face away from grill in operation position. (D). Remove the (2) M5xl0 screws, M5 lock washers and M5 flat washers pre-assembled to the push bar ends, and use them to attach push bar to shelf. (A) Attach fascia to left side shelf with (2) M5xl0 screws, M5 lock washers and M5 flat washers.
- Page 22 Right Side Shelf Remove sideburner grate from sideburner before assembling and attaching the right side shelf. Attach fascia to right side shelf with (2) M5xl0 screws, M5 lock washers and M5 flat washers. (A) Hang right side shelf onto the brackets on right side of firebox. Attach shelf to firebox as follows: - From inside to outside of firebox with (2) M6x13 screws and M6 compression washers.
- Page 23 Sideburner Loosenside burner in side shelf. (B). To loosen, unscrew and remove two front screws and washers holding sideburner in place. (A). Note: Do not loosen electrode screw. Remove knob and bezel from sideburner control valve. To remove, pull knob straight out from valve stem.
- Page 24 Heat Diffusers, Cooking Grate and Warming Rack Place heat diffusers over burners by inserting tabs into slots in front and back of firebox.The diffuser with the extended heat shield must be placed on the far right, with the shield facing to the right.
- Page 25 Grease Cup Clip, Grease Cup and LPtank Hang grease cup clip from bottom of firebox and place grease cup into grease cup clip. Feed the regulator and hose through the hole in the right side panel. LP tank is sold separately. Use only with an OPD (Overfill Protection Device) equipped LP tank.
-
Page 26: Gas Issues
EMERGENCIES: If a gas leak cannot Gas leaking from • Damaged hose cracked/cut/burned hose • Mechanical Gas leaking from LP mishandling cylinder • Failure of cylinder valve from Gas leaking from LP mishandling or mechanical failure cylinder valve • Improper installation, connection not Gas leaking between LF cylinder and regulator tight, failure of rubber seat... -
Page 27: Electronic Ignition
Troubleshooting (continued) ELECTRONIC IGNITION: Burner(s) will not light using ignitor. • No spark, no ignition noise. (See Electronic Ignition • No spark, some ignition noise. Troubleshooting also) • Sparks, but not at electrode or at full strength. Burner(s) will not •... - Page 28 Troubleshooting - Electronic Ignition SECTION I • Battery not installed properly. No sparks appear at any electrodes when control knob turned • Dead battery. to HI: no noise can be heard from spark module. • Button assembly not installed properly. •...
- Page 32 For troubleshooting, For repair - in your home - of all major brand appliances, lawn and garden equipment, no matter who made it, no matter who sold it! For the replacement owner's manuals that you need to do-it-yourself. For Sears professional and items like garage door openers and water heaters.