Panasonic KX-FL513RU Service Manual page 63

6.2.3. SERVICE FUNCTION TABLE
Code Function
501 Pause time set
502 Flash time
503 Dial speed select
514 Bell signal detect time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
529 Call Service Clear
544 Selecting the document feed position 0~4mm
550 Memory clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
599 ECM frame size
628 H.V.P.S. check
Set Value Effective Default
Range
X 100 msec 001~600
X 10 ms 01~99
1:10 pps 2:20 1, 2
pps
X 100msec 1~9
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
0~4
1:ON 2:OFF 1, 2
1:OFF 1~3
2:PHASE B
3:ALL
1:61% 2:67% 1, 2
X number of 00~99
times
X second 001~999
X number of 01~99
rings
X number of 00~99
times
X second 001~999
1:OFF 1~3
2:ALL
3:AUTO
1:75 msec 1~3
2:500 msec
3:1 sec
1:detects at 1, 2
the 1st time
2:detects at
the 2st time
1: 5% 1~4
2: 10%
3: 15%
4: 20%
X dBm - 15~00
43= -43 dBm 20~48
1:256 2:64 1, 2
63
Remarks
030 ----------
085 ----------
1 ----------
6 ----------
1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119).
1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119).
1 The resolution reverts to the default when
transmission is complete.
1 Set RX equalizer to automatic mode.
1
2 When the ADF function is incorrect, adjust the
feed position.
See (P.65).
See (P.65).
2 See (P.65).
1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See (P.65).
See (P.65).
0 See (P.65).
See (P.65).
See (P.65).
See (P.65).
1 Sets the % break of pulse dialing according PBX.
03 Selects the number of times that ITS is redialed
(not including the first dial).
065 Sets the interval of ITS redialing.
10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
03 Selects the number of redial times during FAX
communication (not including the first dial).
65 Sets the FAX redial interval during FAX
communication.
2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to (P.112).
1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119). Refer
to (P.113) and (P.119).
1 See Symptom/Countermeasure Table for long
distance and international calls in (P.119). Refer
to (P.112) and (P.119).
2 If the number of errors during transmission
exceeds this value, the sending side terminates
the call.
13 Selects the FAX transmission level. Refer to
(P.112)and (P.113).
41 Used when there is an error problem. Refer to
(P.119).
1 ----------
See (P.65).
KX-FL513RU