Broan XB50 Installation Manual
Single-speed ventilation fan
Hide thumbs
Also See for XB50:
- Installation manual (28 pages) ,
- Installation manual (40 pages) ,
- Installation manual (20 pages)
Advertisement
READ AND SAVE THESE INSTRUCTIONS
Installer: leave this guide with homeowner.
Register your product online at www.broan.com/register.
Easy installation in both
new construction and retrofit
© 2011 Broan-NuTone LLC
XB50
XB80
n
n
X1 | Single-Speed
Ventilation Fan
INSTALLATION GUIDE
Table of Contents
XB110
2
2
3
7
12
12
12
13
13
Advertisement
Table of Contents
Related Manuals for Broan XB50
Summary of Contents for Broan XB50
-
Page 1: Table Of Contents
XB80 XB110 READ AND SAVE THESE INSTRUCTIONS X1 | Single-Speed Installer: leave this guide with homeowner. Ventilation Fan Register your product online at www.broan.com/register. INSTALLATION GUIDE Table of Contents Warnings and Cautions Typical Installation New Construction Installation Easy installation in both... -
Page 2: Warnings And Cautions
Page 2 XB50 XB80 XB110 Installation Guide WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR . For general ventilating use only. Do not use to exhaust INJURY TO PERSONS, OBSERVE THE FOLLOWING: hazardous or explosive materials and vapors. -
Page 3: New Construction Installation
Page 3 XB50 XB80 XB110 Installation Guide New Construction Installation Tools needed Materials needed • Power screwdriver with a Phillips bit • 6" round metal ducting recommended for best performance. Use of other ducting is acceptable but may impact performance. - Page 4 Page 4 XB50 XB80 XB110 Installation Guide New Construction Installation Snap-in and Secure Housing Position Housing between joists and crimp channel on both sides of Mounting Frame to lock Housing in place. Do not crimp Housing. Screws from Parts Bag...
-
Page 5: Connect Wires And Install Knockout Plate
Page 5 XB50 XB80 XB110 Installation Guide New Construction Installation Connect Wires and Install Knockout Plate • Run 120VAC electrical wiring to the installation location. • Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag. - Page 6 Page 6 XB50 XB80 XB110 Installation Guide New Construction Installation Insert Mask and Finish Ceiling • Install ceiling material. • Cut out around Housing. Mask protects unit during construction. Remove before installing Grille. Install Grille See Page 12 for Operations, Cleaning and Maintenance, and Troubleshooting.
-
Page 7: Retrofit Installation
Page 7 XB50 XB80 XB110 Installation Guide Retrofit Installation Tools needed Materials needed • Power screwdriver with a Phillips bit • Ruler • Tape to seal duct connections • Phillips screwdriver • Pencil • Existing rigid duct will require the addition of a short length of flexible duct •... - Page 8 Page 8 XB50 XB80 XB110 Installation Guide Retrofit Installation Remove Blower Assembly Set aside Blower Assembly Both sides Remove Wiring Panel Set aside Wiring Panel Set aside screw Insert Mounting Frame Remove screws from Mounting Frame Bend up and set aside...
- Page 9 Page 9 XB50 XB80 XB110 Installation Guide Retrofit Installation Secure Mounting Frame Screws set aside in Step 7 Snap-in Housing Pull existing wiring into Housing as it is inserted into Mounting Frame Attach Ducting and Duct Connector Screw from Parts Bag...
- Page 10 Page 10 XB50 XB80 XB110 Installation Guide Retrofit Installation Install Knockout Plate, Connect Wires and Install Wiring Panel • Use proper UL-approved connectors to secure wiring to the Knockout Plate provided in Parts Bag. • Connect wires as shown in wiring diagram.
- Page 11 Page 11 XB50 XB80 XB110 Installation Guide Retrofit Installation Insert and Secure Blower Assembly Screws from Parts Bag If ceiling repairs are needed, place Mask in Housing after Blower Assembly is secured. See New Construction Installation Step 6. Remove Mask before installing Grille.
-
Page 12: Operation
Page 12 XB50 XB80 XB110 Installation Guide WARNING Troubleshooting Before servicing or cleaning unit, switch power off at service panel and lock the service Symptom: The fan does not run. disconnecting means to prevent power from being • Check for an open fuse or circuit breaker in the switched on accidentally. -
Page 13: Service Parts
Fan or part thereof, to the extent Broan finds it to be covered by and in breach of this limited warranty. Broan will ship the repaired or replaced Fan or replacement parts to you at no charge.