15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any other adjustments mentioned in this owner’s manual. SAVE THESE INSTRUCTIONS The design and specifications are subject to change without a prior notice. www.aaasewing.com 900cpx Owners Manual/ User Guide...
Hemming with the Cover Stitch ................ 19 Free Arm Hemming ..................19 Cover Stitch Applications ................. 20 CARE OF YOUR MACHINE Cleaning the Feed Dogs and Looper Area ............21 Replacing the Light Bulb .................. 21 Troubleshooting....................22 www.aaasewing.com 900cpx Owners Manual/ User Guide...
— when threading or cleaning the machine. * Do not place anything on the foot control, Foot controller Model YC-482-J except when the machine is in use. is for use with sewing machine model 900P. www.aaasewing.com 900cpx Owners Manual/ User Guide...
Pull the table away from the machine. q Extension table Attaching the table: Align the pin on the table with the hole in the machine. Push the extension table until it snaps into the machine. w Pin e Hole www.aaasewing.com 900cpx Owners Manual/ User Guide...
* For regular sewing, set the adjusting screw so the head protrudes 10 mm from the top of the machine. q To decrease w To increase e Adjusting screw r Top of the machine www.aaasewing.com 900cpx Owners Manual/ User Guide...
• Set the dial at a higher number when sewing stretch fabrics such as knits, jersey and tricot. q Differential feed dial w Setting mark e To shrink r To stretch www.aaasewing.com 900cpx Owners Manual/ User Guide...
Pull the holder down to remove it. y Needle threader/holder NOTES: Use Schmetz needles EL X 705 size 80/12 or EL X 705 size 90/14. Do not use any needle which is bent or blunt. www.aaasewing.com 900cpx Owners Manual/ User Guide...
When using small spools, remove the spool holders from the spool pins. r Small spool of thread t Spool pin Place the spool with its slit side up, and put the spool holder cap on top of it. y Spool holder cap www.aaasewing.com 900cpx Owners Manual/ User Guide...
Raise the presser foot lifter. q Presser foot lifter NOTE: Always thread the machine with the presser foot raised. Turn the handwheel toward you to bring the needles to their highest position. w Handwheel www.aaasewing.com 900cpx Owners Manual/ User Guide...
(B). q Thread guide bar 2 Pass the thread through the holes on the right side of the thread guide plate as illustrated. w Thread guide plate www.aaasewing.com 900cpx Owners Manual/ User Guide...
4 Push the threader and the thread will go through the needle eye. 5 Remove the threader from the needle. Then pick up the loop of the thread with the hook. Pull the thread end out to the back. t Hook www.aaasewing.com 900cpx Owners Manual/ User Guide...
(B). q Thread guide bar 2 Pass the thread through the holes on the right side of the thread guide plate as illustrated. w Thread guide plate www.aaasewing.com 900cpx Owners Manual/ User Guide...
Page 18
Draw the thread end 4” (10 cm) to the back. o Looper thread guide (D) !0 Eye of the looper NOTE: You may use a pair of tweezers. 9 Push the looper in the direction of the arrow, back to the original position. www.aaasewing.com 900cpx Owners Manual/ User Guide...
Tighten the needle thread tension, and/or loosen the looper thread tension to correct it. (B) If the needle thread tension is too tight: – The fabric puckers. Loosen the needle thread tension, and/or tighten the looper thread tension to correct it. www.aaasewing.com 900cpx Owners Manual/ User Guide...
Tighten the needle thread tension, and/or loosen the looper thread tension to correct it. (B) If the needle thread tension is too tight: – The fabric puckers. Loosen the needle thread tension, and/or tighten the looper thread tension to correct it. www.aaasewing.com 900cpx Owners Manual/ User Guide...
4 Cut the connecting threads between the work fabric and scrap fabric. t Connecting threads Knotting the threads Draw the needle threads to the wrong side of the fabric by using a pair of tweezers and knot them together. www.aaasewing.com 900cpx Owners Manual/ User Guide...
3 Pull the needle threads before the needle eyes. This prevents the threads from being caught when removing the fabric. 4 Pull the fabric to the rear. 5 Remove the fabric and cut the threads with the thread cutter. e Thread cutter www.aaasewing.com 900cpx Owners Manual/ User Guide...
3 Continue to sew over the stitches 2” (4 to 5 cm) beyond the beginning of the seam and stop the machine. Cut the threads at the beginning and at the end. www.aaasewing.com 900cpx Owners Manual/ User Guide...
Wrong side of the fabric Attaching elastics q Right side of the fabric w Wrong side of the fabric e Elastic Decorative stitch q Right side of the fabric w Wrong side of the fabric www.aaasewing.com 900cpx Owners Manual/ User Guide...
“A”) to remove it. Push up and twist the bulb clockwise (in the direction “B”) to replace it. 3 Attach the face plate with the setscrew. q Setscrew w Face plate e Light bulb www.aaasewing.com 900cpx Owners Manual/ User Guide...
1. The tension is out of balance. See page 4. Machine does not 1. The machine is not connected to the power supply. See page 4. operate. 2. The foot control is not plugged in firmly. www.aaasewing.com 900cpx Owners Manual/ User Guide...