Sony Ipela SNC-VM600 Installation Manual page 2

E
1
SNC-VM600/VM600B/VM630/ SNC-VM601/VM601B/VM631/
EM600/EM630 EM601/EM631




Dome casing
2
Ceiling
Bracket
(supplied)
3, 4
Ceiling
Temporary
tightening hook
(3 positions)
Wire rope
M3
(supplied)
screw
(supplied)
Temporary
tightening
hook (3
positions)
Camera unit
mounting
screw (2)
Wire rope
Bracket
mounting
screw hole
Projection
F
Lens case
G
wrench
SNC-VM600/VM600B/VM630/ SNC-VM601/VM601B/VM631/
EM600/EM630 EM601/EM631
H
SNC-VM600/VM600B/VM630/ SNC-VM601/VM601B/VM631/
EM600/EM630 EM601/EM631
Ø148 (5 / )
7
8
Installing the Camera
1
Guide
Remove the dome casing.
SNC-VM600/VM600B/VM630/EM600/EM630
 Pull out the screw cover and loosen the screw with a screwdriver.
 Turn the dome casing anticlockwise, and remove it from the camera unit.
When the screw catches on the screw hole, pull up the screw.
SNC-VM601/VM601B/VM631/EM601/EM631
 Loosen the screw with the wrench (supplied).
 Turn the dome casing anticlockwise, and remove it from the camera unit.
When the screw catches on the screw hole, pull up the screw.
2
Install the supplied bracket on the ceiling or wall.
Refer to "Mounting screws" for screws to be used.
3
Fix the supplied wire rope to the camera unit and the ceiling or wall.
 Fix the wire rope with the supplied M3 screw to the hole for the wire rope
on the bottom of the camera unit.
Pass the wire rope between the wire rope guides.
 Fix the wire rope to the ceiling or wall.
4
Attach the camera unit to the bracket.
 Align the projection on the top and bottom of the camera's card slot with
the bracket mounting screw hole on the bracket.
ˎTurn the camera unit lightly in the direction of the arrow (clockwise
rotation), then lock the temporary tightening hook of the camera (3
positions).
ˎTurn the camera in the rotational direction until it completely stops and
tighten the camera unit mounting screws in the order of 1, then 2.
Notes
ˎ Be sure to tighten the camera unit mounting screws in the order of 1, then 2.
Otherwise, the camera unit may not be secure and could fall.
ˎ If you cannot use screws on a ceiling or wall, or if you want to make the
camera less conspicuous, use the YT-ICB600 in-ceiling bracket (optional) with
which you can mount the camera on the ceiling.
When you install the camera with the in-ceiling bracket, tighten the fixing
screw on the side brackets to the  position. Refer to the in-ceiling bracket
Installation Instructions for details.
Adjusting the Camera Direction and Coverage
You can adjust all pan, tilt and rotation positions. There is no screw for rotation
position.
Turn the lens case to rotate the camera.
You can invert the image by using the setting menu.
1
Loosen the camera head fixing screw.
 Loosen the tilt screws (2 positions).
ˎLoosen the pan screws (2 positions).
2
Adjust the camera to turn the lens in the desired direction.
3
Tighten the camera head fixing screw to fix the camera. (4 positions)
4
Slide the ZOOM/FOCUS switch to W/T to adjust the zoom.
5
Hold down the ZOOM/FOCUS switch for a moment to automatically
adjust the focus.
6
Repeat steps 1 to 5 until the coverage and the focus are determined.
Notes
ˎ
When you adjust the camera head angle without loosening camera head
fixing screw, an internal part may be damaged.
ˎ
Be sure to turn off the setting of superimposing when adjusting the focus.
ˎ
If you cannot achieve satisfactory focus with holding down the ZOOM/FOCUS
switch due to the shooting environment, slide the ZOOM/FOCUS switch level
to N/F to focus manually.
ˎ
Poor focus may also be caused by the dome case assembly. Readjust the focus
using the system menu.
For details, refer to the User's Guide of the equipment.
Notes
ˎ
When the dome casing is attached it may be visible in the monitor
depending on zoom and rotation. Also, distortion might be observed in
mark
images shot outside the specified optical area.
ˎ
Do not turn the tilt screw more than 360 degrees and pan screw more than
2-3 turns, as they may become loose and fall out.
Attaching the Dome Casing
1
Align the notch on the dome casing with the convex part on the rear of
the camera unit, then turn the dome casing in the direction of the arrow.
2
Secure the screw. Only the SNC-VM600/VM600B/VM630/EM600/EM630
cover should be attached.
3
Remove the protecting film on the dome cover.
Connection
Connecting to the Network
Connect the LAN connector of the camera to a PoE* supported device (such as a
hub) using the network cable (straight, not supplied).
The electrical power is supplied through the network cable. For details, refer to
the instruction manuals of the PoE supported devices.
(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant
devices.)
SNC-VM600/VM600B/VM630/VM601/VM601B/VM631
It is also possible to connect the LAN port of the camera to a router or hub in the
network using a network cable (not supplied).
Connecting the Power Source
The camera can be powered in the following ways.
ˎ
12 V DC or 24 V AC (Either voltage supported by SNC-VM600/VM600B/VM630/
VM601/VM601B/VM631 only.)
ˎ
Power supply equipment pursuant to IEEE802.3af (PoE* system)
*PoE means Power over Ethernet.
Note
Ø148 (5 / )
7
8
ˎ
Do not turn off the camera immediately after turning it on. Wait for at least five
minutes before turning off the camera.
ˎ
Do not connect the power input cable if power is supplied by a PoE system.
Connecting to the power supply equipment pursuant to
IEEE802.3af
The power supply equipment pursuant to IEEE802.3af supplies the power
through the network cable. For details, refer to the Instruction Manual of the
equipment.
Connecting to 12 V DC or 24 V AC source
Connect the power input cable of the camera to a 12 V DC or 24 V AC source.
Unit: mm (inches)
ˎ
Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. Each usable
voltage ranges are as follows.
12 V DC: 10.8 V to 13.2 V
24 V AC: 19.2 V to 28.8 V
- In the USA, The product shall be powered by a UL Listed Class 2 Power
Supply Only.

- In Canada, The product shall be powered by a CSA certified Class 2 Power
Supply Only
ˎ
Use UL cable (VW-1 style 10368) for these connections.
Recommended cable
DC 12 V:
CABLE(AWG)
Max. length(m)
AC 24 V:
CABLE(AWG)
Max. length(m)
Connecting the I/O Cable
Compatible models: SNC-VM600/VM600B/VM630/VM601/VM601B/VM631
Connect the wires of the I/O cable as follows:
Wiring diagram for sensor input
Mechanical switch/open collector output device
Camera inside
3.3 V
10 KΩ
2.2 KΩ
10 KΩ
10 KΩ
GND GND GND

Wiring diagram for alarm output
Camera inside
Alarm Output +
Magnet relay –
24 V AC
24 V DC,
1 A or less
Alarm Output –
Specifications
Compression
Video compression format
Audio compression format
Maximum frame rate
Camera
Signal system
Image device

Synchronization
Horizontal resolution
Video S/N
Minimum illumination
* VE stands for Visibility Enhancer.
Lens
Focal length
Maximum relative aperture
View angle
Movable angle
Minimum object distance
Interface (SNC-VM600/VM600B/VM630/VM601/VM601B/VM631)
LAN port (PoE)
I/O port
SD memory card slot
Video output
Microphone input*
Line input*
#24 #22 #20
* The microphone input and the line input are switchable with operating menu.
9 15 23 Line output
Interface (SNC-EM600/EM630/EM601/EM631)
LAN port (PoE)
#24 #22 #20
37 63 92
Others
Power supply
Power consumption
Operating temperature
Outside
Storage temperature
Operating humidity
Storage humidity
Dimensions (diameter/height) 
Mass
Mechanical switch
Sensor input +
or
Sensor input −
(GND)
Supplied accessories
Open collector
output device
Outside
5 V
Optional accessory
R
In-ceiling bracket YT-ICB600*
* Using the fixture position  on the bracket.
Dome Cover Smoked
SNC-VM600/VM600B/VM630/EM600/EM630: YT-LD600S
SNC-VM601/VM601B/VM631/EM601/EM631: YT-LD601S
Design and specifications are subject to change without notice.
Circuit example
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over time,
which may cause a malfunction or accident.
GND
For details, please consult the store of purchase or an authorized Sony dealer.
JPEG/H.264
G.711/G.726/AAC
SNC-VM600/VM601/VM630/VM631
60 fps
SNC-VM600B/VM601B/EM600/EM630/EM601/
EM631
30 fps
NTSC color system/PAL color system
(switchable)
SNC-VM600/VM600B/VM601/VM601B/EM600/
EM601
1/3type CMOS (Exmor)
Effective picture elements:
Approx. 1,370,000
SNC-VM630/VM631/EM630/EM631
1/2.9type CMOS (Exmor)
Effective picture elements:
Approx. 2,140,000
Internal synchronization
SNC-VM600/VM600B/VM601/VM601B: 600 TV
lines (analog video)
SNC-VM630/VM631: 700 TV lines (monitor
display ratio 4:3)
More than 50 dB (Auto gain control maximum
rate 0 dB)
F1.2/View-DR Off/VE* Off/Auto gain control
maximum rate MAX/50 IRE (IP)/30 fps
SNC-VM600/VM600B/VM601/VM601B/EM600/
EM601
Color: 0.05 lx
Black & White: 0.04 lx
SNC-VM630/VM631/EM630/EM631
Color: 0.10 lx
Black & White: 0.07 lx
3.0 mm to 9.0 mm
F1.2 to F2.1
SNC-VM600/VM600B/VM601/VM601B/EM600/
EM601: 1280 × 1024 (aspect ratio 5:4)
Vertical: 73.1° to 25.5°
Horizontal: 92.9° to 31.8°
SNC-VM630/VM631/EM630/EM631: 1920 × 1080
(aspect ratio 16:9)
Vertical: 56.9° to 20.1°
Horizontal: 105.3° to 35.6°
Pan: −192° to +192°
Tilt: −7° to +75°
Rotation: −99° to +99°
300 mm
10BASE-T/100BASE-TX, auto negotiation (RJ-45)
Sensor input: × 2, make contact, break contact
Alarm output: × 2, 24 V AC/DC, 1 A
(mechanical relay outputs electrically isolated
from the camera)
VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms,
unbalanced, sync negative
Minijack (monaural)
Plug-in-power supported (rated voltage: 2.5 V DC)
Recommended load impedance: 2.2 kΩ
Minijack (monaural)
Minijack (monaural), Maximum output level:
1 Vrms
10BASE-T/100BASE-TX, auto negotiation (RJ-45)
IEEE802.3af compliant (PoE system)
SNC-VM600/VM600B/VM630/VM601/VM601B/
VM631:
12 V DC ±10%, 24 V AC ±20% 50 Hz/60 Hz
SNC-VM600/VM600B/VM630/VM601/VM601B/
VM631: 6.0 W max.
SNC-EM600/EM630/EM601/EM631: 5.0 W max.
Start temperature: 0°C to 50°C (32°F to 122°F)
Working temperature: −10°C to +50°C (14°F to
122°F)
–20°C to +60°C (–4°F to +140°F)
20% to 80%
20% to 95%
148 mm × 108 mm (5 / inches × 4 / inches)
7 3
8 8
SNC-VM600/VM600B/VM630/EM600/EM630:
Approx. 760 g (1 lb 8.7 oz), not including the
cables and bracket
SNC-VM601/VM601B/VM631/EM601/EM631:
Approx. 800 g (1 lb 12 oz), not including the
cables and bracket
All models: CD-ROM (supplied programs) (1),
Bracket (1), Template (1), Wire rope (1), Camera
unit mounting screw M3 (1), Safety Regulations,
Installation Manual (this document) (1 set)
SNC-VM601/VM601B/VM631/EM601/EM631:
Wrench (1)
SNC-VM600/VM600B/VM630/VM601/VM601B/
VM631: Audio cable (1), I/O cable (1), BNC cable
(1), Power input cable (1)