Related Manuals for Hobart UX Series
Summary of Contents for Hobart UX Series
-
Page 1: Operation Instructions
WaShINg MachINES uX SERIES INStallatIoN aNd opERatIoN INStRuctIoNS Starting from Serial No.: 8650 6000 REV. 04.09.2009... - Page 2 AG-21213-F-09-09...
-
Page 3: Table Of Contents
coNtENt Page IMpoRtaNt NotES ..............4 INStallatIoN ................5 2.1 Location ..................5 2.2 Electrical connection ............... 5 2.3 Water connection ................5 2.4 Steam connection (steam heated machines only) ......6 2.5 Adjustment of shut-off valve for steam supply ........6 2.6 Drain connection ................ -
Page 4: Important Notes
IMpoRtaNt NotES use in accordance with Regulations This machine is exclusively to be used to wash ware such as pots and pans, baking sheets, cutlery, trays etc. do not use for electrically heated cooking and heat conservation appliances. Do not put heavy objects on the top of the machine. Safety do not stand on the open front door of the machine. -
Page 5: Installation
INStallatIoN locatIoN – Wall clearance is not required at the rear. – The lateral distance between machine and wall should be 400 mm on one side. – To avoid damage of the feet, do not slide the machine on floor after the skid is removed. -
Page 6: Steam Connection (Steam Heated Machines Only)
– The correct adjustment is very important particularly for higher pres- sure, and therefore must be done by a HOBART trained service techni- cian at first installation or after any changes are done at the customer site. -
Page 7: Connecting Of Detergent Pump
coNNEctINg oF dEtERgENt puMp If the machine is not equipped with a detergent pump, installation of an external dispenser must be done as follows. Must be carried out by an authorized technician according to the local and national codes. – Tank must be drained. –... - Page 8 To connect a powder or solid detergent dispenser: – Remove the rear panel. – Drill a hole through the inner tank wall appropriate to the required connection diameter (see fig.). – Screw up tightly the dosing connection with tank wall. –...
-
Page 9: Controls
coNtRolS À Machine oN / oFF By pushing this button the machine will be switched on. (illuminates during In case of emergency (e.g. faults), it is possible to switch off the machine operation) immediately without drain cycle, by pushing this button again. after switch off, the machine is not voltage free! Á... -
Page 10: Start-Up
StaRt-up RINSE aId – Place the suction hose (blue marking) into the rinse aid container. Fill the suction hose according to chapter 6.5. dEtERgENt do not use any acidic detergent products with the built-in detergent pump! (the ph-value has to be higher than 7.) –... -
Page 11: Settings
If the door is closed or if no button is pressed for 10 seconds, the indicator automatically switches off and the new settings are saved. adjuStMENt oF dEtERgENt doSagE quaNtIty (delivery values are only valid with built-in HOBART detergent pump) The temperature indicator Rinse Å displays: "CH1"... -
Page 12: Priming The Suction Hoses
SEttINgS pRIMINg thE SuctIoN hoSES (only with built in detergent pump) To prime the detergent suction hose between the injector and container: – Close door The temperature indicator Rinse Å displays: "SF1" = Priming of detergent suction hose. – Push and hold Start button Á... -
Page 13: Operation
opERatIoN pREpaRatIoN – Check correct position of wash/rinse arms and strainers. – open shut-off valve. – Switch on main switch or put the plug in. – Check level of detergent and rinse aid containers. À – Close door and push the ON button , tank will be filled. -
Page 14: Run
opERatIoN – Put rack into the machine and close door. – Push the Start button Á . As long as the wash cycle is running, the Start button illuminates blue. – As soon as the Start button changes to green, the wash cycle is fini- shed. -
Page 15: Preview Of Temperatures
pREVIEW oF tEMpERatuRES – Press the Program button à and hold (3 sec.) until the indicators Wash Ä and Rinse Å show the actual temperatures (°C). The indicators go out 10 sec. after releasing Program button. Permanent temperature display can be activated on request by the service technician. -
Page 16: Frost Prevention
REFIllINg thE SoFtENER WIth Salt only for machines with optional built-in softener. – When the Salt required Æ indicator illuminates, the softener has to be filled with regeneration salt. – Wait until the wash program is finished. – Open the door. –... -
Page 17: Faults
FaultS – the Service indicator Ç illuminates and the temperature indicator Rinse Å displays a code: e.g. "al" = drain fault. possible types of fault as follows (please report the code of fault to the service technician). poSSIBlE cauSE MEaSuRES codE Shut-off valve is closed. - Page 18 tRouBlEShootINg guIdE typE oF FaIluRE poSSIBlE cauSE REMEdy poor wash result Washware is not clean. Wash arms blocked (you should be able Take out wash arms and clean them thoroughly. to turn them easily by hand). Check water outlet from machine to wash arms is clear.
-
Page 19: Troubleshooting Guide
tRouBlEShootINg guIdE typE oF FaIluRE poSSIBlE cauSE REMEdy poor wash result Stripes and staines on Rinse aid concentration too high. Reduce quantity (see instructions). dishes or glasses. Hard water or high mineral content. Check water quality. Obtain details from local water authority. Recommended values: Ideal degree of hardness is 4°... - Page 20 As continued product improvement is a policy of HOBART, specifications are subject to change without notice. Printed in Germany ag-21213-F-09-09-pc...