Page 1
Glass and Dishwashers AMXXT / AUXXT Series INSTALLATION OPERATION REV. 8.xx – 04.07.2005...
Page 2
Important Notes ● Use in Accordance with Regulations This machine is exclusively to be used to wash ware such as plates, cups, glasses, cutlery, trays etc. Do not use for electrically heated cooking and heat conservation appliances. ● Safety Never hose down the machine. The "Attention"...
Installation Location – Rear wall clearance not required. For corner installation lateral clearance of 107 mm is required. For free-standing installation the optional rear panel has to be installed. – Level machine by turning the feet. – Distribute machine weight equally onto all feet. Converting to corner operation Depending on direction of operation, one of the rack guides may need to be adjusted to suit the direction of operation (see arrow).
Water connection Must be carried out by an authorized technician according to the national and local codes. The machine must be operated with water of drinking quality. For water with an extremely high mineral content, water treatment is recommended. Machines without softener –...
Page 6
– Lift up control box and turn it to front. TO CONNECT A LIQUID DETERGENT DISPENSER: – Remove blanking plug (A) at tank (either at the right or left tank). – Install detergent inlet fitting + gasket (B). – Connect a hose (PVC / 6mm outside Ø x 4mm inside Ø) between outlet of the detergent pump and the detergent inlet (B) of the wash tank.
Page 7
TO CONNECT A POWDER OR SOLID DETERGENT DISPENSER: – Break out perforated disk at the tank panel (either at the right or left side). – Drill a hole through the inner tank wall appropriate to the required connection diameter. – Screw up tightly the dosing connection with tank wall. –...
Controls ➀ Machine ON / OFF By pushing this button the machine will be switched on. (illuminates during operation) In case of emergency (e.g. faults), it is possible to switch off the machine immediately without drain cycle, by pushing this button again.
First run Rinse agent – Put the suction hose (blue) into the rinse agent storage container. Detergent (only on option) Do not use any acid detergent products with the built-in detergent pump! (The ph-value has to be higher than 7.) –...
If no button is pressed during next 10 secs., the indicator switches off and the new settings will be saved. Adjustment of detergent dosage quantity (delivery values are only valid with built-in HOBART dispenser) ➃ – Push Program button again.
Priming of suction hose detergent (only with built in detergent pump) To prime the detergent suction hose between the injector and container: – Close hood. ➅ The temperature indicator Rinse displays: "SF1" = Priming of detergent suction hose. ➁ – Push and hold Start button for 1 minute approx.
Page 12
– Place glasses and cups with the opening facing downwards into the rack. – Remove coarse food soil before loading plates into rack. – Spray off greasy food soil. GENERAL: As detergent will be dosed into one tank only, uniform detergent concentration is not reached during the first wash cycle.
– Select program: The machine is operating automatically with standard cycle time. If needed, it is possible to select a shorter or longer program. ➃ To show the present program, push Program button before starting the wash cycle. To change the program, push Program button again.
Switch-off and cleaning the machine Switch-off ➂ – Close hood, push and hold Drain-button for 2 secs. NOTE: During the drain cycle, the interior of the machine is cleaned automatically. A final inspection is recommended to remove coarse soil. – When Drain-button goes off, switch off main switch or unplug and close shut off valve at site! Cleaning (daily) –...
Refilling the softener with salt Only for machines with optional built-in softener. ➆ – When the Salt required indicator illuminates, the softener has to be filled with regeneration salt. – Wait until the wash program is finished. – Open hood. –...
Faults ➇ The Service indicator illuminates and the temperature indicator ➅ Rinse displays a code: e.g. "AL" = drain fault. Possible types of fault as follows (report the code of fault to the service technician): CODE POSSIBLE CAUSE MEASURES Shut-off valve is closed. Open shut-off valve at site and switch on machine again.
Page 17
TYPE OF FAILURE POSSIBLE CAUSE REMEDY Poor wash result Dishes or glasses Rinse aid concentration too low. Increase concentration (see operating do not dry properly. instructions). Dishes still greasy. 1. Detergent concentration too low: increase (see instructions). 2. Check if detergent is appropriate. If not choose a stronger one.
Page 18
As continued product improvement is a policy of HOBART, specifications are subject to change without notice. Printed in Germany AG-21247-C-07-05-PC...