Monogram ZDIC150 Design & Installation Manual
Automatic icemaker
Hide thumbs
Also See for ZDIC150:
- Installation instructions manual (18 pages) ,
- Owner's manual (16 pages) ,
- Design manual with installation instructions (18 pages)
Related Manuals for Monogram ZDIC150
Summary of Contents for Monogram ZDIC150
-
Page 1: Installation Instructions
Installation Instructions Automatic Icemaker ZDIC150 ZDIS150 Design Guide With Installation Instructions monogram.com... -
Page 2: Table Of Contents
In the absence of local codes, the icemaker should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition. For Monogram local service in your area, call 1.800.444.1845. For Monogram Service in Canada, call 1.800.561.3344. -
Page 3: Design Information
3/4″ thick custom panel. OPTIONAL ACCESSORIES ZIP75WW White and ZIP75BB Black—For the ZTBSS1—Monogram tubular stainless steel handle installation of a trimless 3/4″ thick custom panel for 3/4″ thick custom panels. Order this kit from your on white and black models (not for stainless steel Monogram supplier. -
Page 4: Advance Planning
Installation Instructions ADVANCE PLANNING ADVANCE PLANNING (cont.) CAUTION: Due to excessive Before you begin: weight, TWO PEOPLE ARE REQUIRED 1. If a custom panel is to be installed, follow the TO MOVE AND INSTALL THIS ICEMAKER. instructions shown on pages 9 and 10. Failure to do so can result in back or –Order ZIP75 (black or white) panel kit. -
Page 5: Power Supply
Installation Instructions POWER SUPPLY REMOVE PACKAGING AND PARTS WARNING: • Lay the carton on rear face (Please read carefully). and break open the bottom FOR PERSONAL SAFETY, THIS APPLIANCE flap. MUST BE PROPERLY GROUNDED. Failure • Set the carton upright to follow these instructions can result with all four bottom flaps in death, fire or electrical shock. -
Page 6: Water Supply
Installation Instructions WATER SUPPLY WATER SUPPLY (cont.) • A cold water REVERSE OSMOSIS WATER SUPPLY supply is required IMPORTANT: The performance of the icemaker for icemaker may be affected when it is connected to a reverse operation. The 3" 11-1/2" osmosis system. -
Page 7: Connect Water Supply
Installation Instructions CONNECT WATER SUPPLY REVERSE THE DOOR SWING IMPORTANT: • The water line should be flushed to clear any Disconnect power to the icemaker. foreign material before connecting to the icemaker. Tools Required: • Connect the water line to the water supply tube •... - Page 8 Installation Instructions REVERSE THE DOOR SWING REVERSE THE DOOR SWING (cont.) (cont.) Reverse the hinges (all models): Reinstall the door (all models) (cont.): • Remove the screws opposite the door hinges, Top Hinge top and bottom. Set aside. • Remove the two screws holding top hinge. •...
-
Page 9: Zip75Ww, Zip75Bb Kit For 3/4" Thick Panels
Installation Instructions for ZIP75WW, ZIP75BB Kit BEFORE YOU BEGIN: NOTE: If installing a 3/4″ trimless custom panel, • a 1-1/2″ wide filler strip may be required. The filler Read these instructions completely and carefully. strip will act as a spacer between the icemaker IMPORTANT: •... - Page 10 • Tape the side trim pieces to the back of the mounting screws. Set screws aside. Discard handle. custom panel. • The Monogram nameplate is held in place with • Place the panel with trim against the door to be adhesive. Remove the nameplate.
-
Page 11: Ztbss1 Tubular Handle Kit
Owner’s Manual for future reference. • 2 Handle standoffs This kit provides a stainless steel tubular handle • 2 Set screws for standoffs to coordinate with other Monogram appliances. • 2 Nuts • The tubular handle must be installed onto the • 2 Washers 3/4″... - Page 12 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.