Monogram ZDIC150 Installation Instructions Manual
Automatic ice maker
Hide thumbs
Also See for ZDIC150:
- Owner's manual (16 pages) ,
- Design & installation manual (12 pages) ,
- Design manual with installation instructions (18 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for Monogram ZDIC150
Summary of Contents for Monogram ZDIC150
- Page 1 Installation Instructions Automatic Ice maker ZDIC150 ZDIS150 Design Guide With Installation Instructions monogram.com...
-
Page 2: Table Of Contents
In the absence of local codes, the ice maker should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition. For Monogram local service in your area, call 1.800.444.1845. For Monogram Service in Canada, call 1.800.561.3344. -
Page 3: Design Information
Design Information MODELS AVAILABLE ZDIC150ZBB, ZDIS150ZSS The ice maker may be installed below a countertop Available in black and stainless steel. or used free-standing. OPTIONAL ACCESSORIES For the installation of a trimless ZPK2 Drain Pump Kit - For use when a floor drain is 3/4”... -
Page 4: Cutout & Product Dimensions
CABINET 3/4” 110° 120° * For flush installation of ZDIS150 and ZDIC150 models: Install a 1/2”-wide filler strip on the hinge side. The filler strip will act as a spacer between the door case and adjacent cabinets and Corner Installation will prevent interference with the cabinet door swing. -
Page 5: Water Supply
Installation Instructions ADVANCE PLANNING (cont.) ADVANCE PLANNING (cont.) IMPORTANT: LOCATION REQUIREMENTS: This unit must NOT be on a GFCI (Ground Fault Circuit Interrupter) equipped outlet or nuisance tripping may occur resulting in loss of cooling. Ice quality may be affected. If nuisance protected from elements such as wind, rain, water tripping has occurred, and if the condition of the ice spray or drip. -
Page 6: Power Supply
Installation Instructions POWER SUPPLY REMOVE PACKAGING AND PARTS WARNING : (Please read carefully). face and break open the FOR PERSONAL SAFETY, THIS APPLIANCE MUST bottom flap. BE PROPERLY GROUNDED. Failure to follow these instructions can result in death, fire or electrical with all four bottom flaps shock. -
Page 7: Adjust Height Of Ice Maker
Installation Instructions ADJUST HEIGHT AND LEVEL THE WATER SUPPLY SET-UP ICE MAKER with water pressure Height adjustments may be necessary to install between 30 and the ice maker below a countertop, and may be 120 p.s.i. is required accomplished by adjusting both the front and rear for ice maker leveling legs. -
Page 8: Connect Water Supply To Appliance
Installation Instructions CONNECT WATER SUPPLY TO CONNECT WATER LINE (cont.) APPLIANCE For GE SmartConnect Tubing: ™ maker connection. Tighten the compression nut material before connecting to the ice maker. until it is just hand tight. outside of the rear access cover. tightening can cause leaks! Copper Tubing: could restrict water flow. -
Page 9: Connect The Drain
Installation Instructions CONNECT DRAIN This ice maker is equipped with a gravity drain to prevent water from flowing back into the storage bin and Drain Hose overflowing onto 1” Min. Gap the floor. The ideal installation has a 1-7/8” standpipe with a 2” to 1-1/2”... -
Page 10: Reverse Door Swing
Installation Instructions REVERSE THE DOOR SWING (cont.) REVERSE THE DOOR SWING IMPORTANT: STEP 2 - DOOR STOP AND END-CAP REVERSAL Disconnect power to the ice maker. 1. Remove the hinge pin from the top hinge. Tools Required: 2. Remove the door from the hinges and replace the top hinge pin. - Page 11 Installation Instructions REVERSE THE DOOR SWING REVERSE THE DOOR SWING (cont.) (cont.) STEP 3 - REVERSE HINGES STEP 4 - REPLACE DOOR For Black Model: Replace screws in empty hinge holes. Align handle with the holes in the door and replace 2.
-
Page 12: Accessories Zpk2 Auxiliary Pump Kit
Installation Instructions for ZPK2 BEFORE YOU BEGIN: KIT CONTENTS: Read these instructions completely and carefully. IMPORTANT: inlet) Save these instructions for local inspector’s use. IMPORTANT: drain) Observe all governing codes and ordinances. Be sure to leave these cabinet back) instructions with the Consumer. Keep these instructions product) with your Owner’s Manual for future reference. - Page 13 Installation Instructions STEP 1 - REMOVE ORIGINAL PARTS STEP 2 - CONNECT ELECTRICAL 1. Position pump at the right side, just outside of the opening. NOTE: If pump is being installed on a ice maker that has not been completely installed, please proceed to Drain Pump Install section.
- Page 14 Installation Instructions STEP 4 -INSERT DRAIN PUMP STEP 6 - SECURE VENT TUBE 1. Carefully slide the auxiliary drain pump into the 1. Place rear cover against the back of the ice bottom of the ice machine. The tab on the back of machine.
- Page 15 Installation Instructions for ZIP75BB Kit NOTE: If installing a 3/4” trimless custom panel, BEFORE YOU BEGIN: a 1-1/2” wide filler strip may be required. The filler Read these instructions completely and carefully. strip will act as a spacer between the ice maker IMPORTANT: case and the adjacent cabinet, and will prevent interference with the ice maker door swing when...
-
Page 16: Zip75Bb Kit For 3/4" Thick Panels
4. Place the panel with trim against the door to be 2. The Monogram nameplate is held in place with sure that trim and panel fits the door side to side adhesive. Remove the nameplate. and top to bottom. Adjust as needed. - Page 17 Notes...
- Page 18 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call ® 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.