Related Manuals for Monogram 31-46199-1
Summary of Contents for Monogram 31-46199-1
- Page 1 stoll rio structio Automotic Icemaker ZDIC150 ZDIS150 Design Guide With Instollotion Instructions monogram.corn...
-
Page 2: Table Of Contents
Proper installation is the responsibilitg of the installer. Product failure due to improper installation is not covered under the GE Appliance Warrantg. See the Owner's Manual for warrantg information. • Use this appliance onlg for its intended purpose. -
Page 3: Design Information
!0 feet. !0 feet of tubing is supplied with the kit. TOOLS AND MATERIALS REQUIRED • 1//4" socket • 3//4" adjustable wrench • Level GE SmartConnecf" Refrigerator Tubing Kit or 1/4" O.D. copper tubing, of sufficient length to reach the installation... -
Page 4: Advance Planning
Installation Instructions ADVANCE PLANNING ADVANCE PLANNING (cont.) CAUTION: Due t oexcessive Before gou begin: weight, TWO PEOPLE ARE REQUIRED 1. If a custom panel is to be installed, follow the TO MOVE AND INSTALL THIS ICEMAKER. instructions shown on pages 9 and 10. Failure to do so can result in back or -Order ZIP7S (black or white) panel kit. -
Page 5: Power Supply
Installation Instructions POWER SUPPLY REMOVE PACKAGING AND PARTS • Lag the cartonon rearface WARNING: (Please read and break open the bottom FOR PERSONAL SAFETY,THIS APPLIANCE carefully). flap. MUST BE PROPERLY GROUNDED. Failure to follow these instructions can result • Set the carton upright in death, fire or electrical shock. -
Page 6: Water Supply
NOTE: The onlg GE approved plastic tubing is supplied in the GE SmartConnect" Refrigerator Tubing kits. Do CONNECT DRAIN not use ang other plastic water supplg line because the line is under pressure at all times. -
Page 7: Connect Water Supply
Lineto • Lift the door off of the bottom hinge. Place the Icemaker hinge pin back into the top hinge. GE SmartConnect'" Tubing: For stainless steel model: • Insert the molded end of the tubing into the • Remove two screws each from the top and icemaker connection. - Page 8 Installation Instructions REVERSE THE DOOR SWING Icont.I REVERSE THE DOOR SWING Icont.} Reinstall the door (all models) (cont.): Reverse the hinges (all models}: * Remove the screws opposite the door hinges, Top 4inge top and bottom. Set aside. * Remove the two screws holding top hinge. * Turn the hinge upside down, with the hinge pin pointing up.
- Page 9 Installation Instructions for ZIP75WW, ZIP75BB Kit • BEFORE YOU BEGIN: NOTE: If installing a 3/4" trimless custom panel, a 1-1/2" wide filler strip mag be required. The filler Read these instructions completely and carefully. strip will act as a spacer between the icemaker •...
- Page 10 Installation Instructions for ZIP75WW, ZIP75BB Kit STEP 5 SECURE SIDE TRIM PIECES I STEP1 DISCONNECT POWER TO CUSTOM PANEL TO THE ICE MACHINE • Lag the custom panel appearance-side-down on a clean surface. STEP 2 REMOVE HANDLE • Align top and bottom side trim to the custom AND NAMEPLATE panel sides,...
- Page 11 ZTBSSI Monogram Tubular Handle Kit • BEFORE YOU BEGIN: TOOLS AND MATERIALS REQUIRED: Read these instructions completely and carefully. • Gloves to protect against sharp edges • #2 Phillips screwdriver • IMPORTANT: • Drill and 1/4" bit and !/2" spade bit Save these instructions for local inspector's use.
- Page 12 General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Pub.No. 31-46199-1 ] Appliances PartNo. 224D1889P001 General Electric Compan 9 Louisville, KY 40225 W10136140A 07-07 JR ge.com Printed in the United States...