Table of Contents
Advertisement
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting
• The lower section in the items and set values columns shows what's on the VCR's display.
Screens
Items
Set values
DURATION
5 SEC
Selects the recording duration for alarm or sensor recording.
ALARM/
10 SEC
5 — 180 SEC: Alarm or sensor recording is performed for the specified
SENSOR
15 SEC
MODE
30 SEC
TAPE END: Alarm or sensor recording continues to the end of the tape.
60 SEC
MANUAL:
120 SEC
[180 SEC]
TAPE END
MANUAL
5
(VCR's display)
. .
AL SE 3
.
180
TPEN
NANU
TAPE END
[OFF]
Selects whether or not the Stop mode is forcibly engaged when the tape
ends even if there is an alarm or sensor recording.
MODE
STOP
OFF: The forced Stop mode is not engaged.
AL SE 4
OFF
STOP
STOP: The Forced Stop mode is engaged.
BUZZER
TAPE END
[OFF]
Sets whether or not the buzzer sounds when the tape ends in the
Record mode.
ON
OFF: The buzzer does not sound.
BU 22 1
OFF
ON: The buzzer sounds when the tape ends during recording. Also, the
ON
AL/SENSOR
[OFF]
Selects whether or not the buzzer sounds during alarm or sensor
IN
ON
recording.
OFF: The buzzer does not sound.
BU 22 2
OFF
ON: The buzzer sounds.
ON
WARNING
[OFF]
Sets whether or not the buzzer sounds when a warning occurs.
ON
OFF: The buzzer does not sound.
ON: The buzzer sounds. When the warning is released, the buzzer
BU 22 3
OFF
ON
IN/OUT
CAMERA SW
[OFF]
Sets the camera switching signal output interval.
1 FIELD
OFF:
2 FIELD
1 FIELD: Set to this position to switch cameras every 1 field.
2 FIELD: Set to this position to switch cameras every two fields (1
iO
1
OFF
1FRD
2FRD
RS-232C
This screen is shown only when the optional SA-K97U RS-232C board is installed.
B. RATE
600
1200
Selects the RS-232C data transfer rate (600 bps, 1200 bps, 2400 bps,
2400
4800 bps and 9600 bps).
4800
[9600]
600
. .
iO
3
.
9600
26
Function
time (5 sec. to 180 sec.)
Alarm or sensor recording continues for as long as alarm
signals are input. Set to this position when specifying the
alarm recording time with a switcher.
*To ensure accurate alarm search and alarm scan operation,
be sure to set the recording time to 5 seconds or more.
• When the tape ends, the mode set with the menu switch <AUTO
REW> or <REPEAT REC> on the <VTR MODE> screen is engaged.
buzzer sounds when the tape reel counter value set with the menu
switch <CNT TAPE END> on the SRI/EXT MODE screen is reached.
When the mode is changed by pressing the [REW] button,
[EJECT] button or [OPERATE] button, the buzzer sound stops.
sound stops.
No camera switching signal is output.
frame).
5 PREPARATION
5-1 Cassette Loading/Unloading
Loading
Insert the cassette with its label side facing you.
Gently push the center of the cassette until the machine starts automatic loading.
REC
STOP
REC
CHECK
OPERATE
HDR
RESET/
CANCEL
ON SCREEN
REW
REVERSE
PAUSE
PLAY
FF
SHIFT
TRACKING
V. LOCK
TIMER SEARCH
DISPLAY LOCK
CNT RESET
MENU
TIME MODE
–
+
–
+
–
+
S E T
FIELD REV
FIELD ADV
[TIMER] indication
[EJECT] button
(
) indication
Notes:
• To avoid damage or injury, do not insert your hand or other foreign objects into the cassette loading slot.
• For best results, use a T-120 tape.
Auto operate on
When a cassette is loaded, the oprating mode
automatically turns on and the (
) cassette indication
appears.
Unloading
5
Press the [EJECT] button.
[The cassette is ejected.
• The tape reel counter is reset to "0000".
If the operating mode is not on when the [EJECT] button
is pressed, operating mode is automatically switched on
and the cassette is ejected. Once the cassette is
unloaded, the operating mode turns off again
automatically.
SR-9090U
REC
EJECT OPERATE
Auto play
When a cassette with no erasure prevention tab is loaded,
playback starts automatically.
If the Timer Recording Standby mode is engaged
(TIMER indication is shown on the display), the
cassette will not be ejected when the [EJECT] button is
pressed.
To unload the cassette, press the [TIMER] button to
release the Timer Recording Standby mode, then
press the [EJECT] button.
27
Advertisement
Table of Contents
