Table of Contents
Advertisement
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting
• The lower section in the items and set values columns shows what's on the VCR's display.
Screens
Items
Set values
VIDEO MODE
V. PULSE
[OFF]
Sets whether or not the V. pulse is added during ordinary playback
ON
(2H and 6H modes).
OFF: V. pulse is not added. Normally set to this position.
OFF
(VCR's display)
ON: V. pulse is added.
ON
ViD 3
• When a camera synchronized with the power supply is switched with
a switcher, the picture may be distorted at the switching point. In
this case, set this switch to "ON". This locks the monitor, preventing
the picture distortion at switching points (only in the 2/6H mode).
• V. pulse is always added in the Still mode and Timelapse mode.
VTR MODE
HDR
[OFF]
Sets the mode during timelapse recording.
ON
OFF: Records in the normal timelapse mode (timelapse recording with
VTR 1
OFF
ON: Records in the HDR timelapse mode (timelapse recording with
ON
Sets whether or not the counter memory function is activated.
CNT MEM SW
[OFF]
ON
OFF: The counter memory function is not activated.
ON: The counter memory function is activated.
OFF
VTR 2
ON
* The counter memory function is not available during repeat recording/
playback, auto REW, alarm search, alarm scan and date/time search.
POWER ON
[OFF]
Enables or disables automatic external timer recording or automatic
REC
ON
restart of recording after a power failure.
OFF: External timer recording or automatic recording after power
OFF
VTR 3
ON
ON: Recording starts automatically when power is turned on.
AUTO REC
[OFF]
Sets whether or not Recording Check is automatically performed at the
CHECK
ON
beginning of a tape in the Repeat Recording mode.
OFF: Automatic recording check function is disabled.
OFF
VTR 4
ON: Automatic recording check function is enabled.
ON
AUTO REW
[OFF]
Sets whether or not the tape is rewound automatically when the tape
ON
ends.
OFF: The tape stops at the end.
OFF
VTR 5
ON: The tape automatically rewinds and enters the Stop mode (auto
ON
* When the repeat recording/playback function is set to "ON", the
repeat function has priority.
* If the menu switch <TAPE END MODE> on the <ALARM/SENSOR
MODE> screen is set to "STOP", the Stop mode is engaged when
the tape ends even when there is an alarm or sensor recording. The
tape does not rewind.
REPEAT PLAY
[OFF]
Enables or disables the repeat playback function.
ON
OFF: The repeat playback function is disabled.
ON: When the tape ends, it is automatically rewound and played back
OFF
VTR 6
ON
24
Function
the SP heads).
the EP heads). Refer to page 28.
When the tape reel counter value reaches 0000 in the FF/REW
mode, the VCR enters the Stop mode automatically.
failure does not function regardless of whether power is supplied
or not.
REW).
again from the beginning.
4 ON-SCREEN/MENU SWITCHES
4-7 Contents of Menu Switches
[ ]: Factory setting
• The lower section in the items and set values columns shows what's on the VCR's display.
Screens
Items
Set values
Enables or disables the repeat recording function.
VTR MODE
REPEAT REC
[OFF]
OFF: The repeat recording function is disabled.
ON
ON: When the tape ends, it is automatically rewound and recording
OFF
(VCR's display)
ON
VTR 7
* If the menu switch <TAPE END MODE> on the <ALARM/SENSOR
MODE> screen is set to "STOP", the Stop mode is engaged when
the tape ends even when there is an alarm or sensor recording. The
repeat recording is not executed.
* When this menu switch is set to "ON", externally activated recording
is not executed.
Selects series recording or automatic recording with an external VCR activation
SRI/EXT
SRI/EXT REC
[OFF]
signal.
MODE
SERIES
OFF:
EXT
OFF
SR ET 1
SERIES: The series recording function is enabled.
SERi
EXT:
EiT
* When the menu switch <REPEAT REC> is set to "ON", externally
activated recording is not executed.
Selects the mode engaged when externally activated automatic
EXT REC END
[NORMAL]
recording ends.
OPE OFF
NORMAL: The Stop mode is engaged.
SR ET 2
NORn
OPE OFF: The Stop mode is engaged and the operating power mode
POFF
CNT TAPE END [OFF]
Outputs a tape end signal from the rear panel's [TAPE END OUT] terminal
500
when the tape reaches the set tape reel counter value during recording.
During series recording, a series recording signal is output to a connected
1000
. .
VCR for continuous recording.
.
OFF: The counter end output function is disabled.
9500
500 : A tape end signal is output when the set tape reel counter value is
OFF
SR ET 3
. .
.
500
9500
. .
.
9500
ALARM/
REC MODE
[OFF]
Selects the alarm recording or sensor recording function.
SENSOR
ALARM
• Alarm recording: When an alarm signal is input to the rear panel's
MODE
SENSOR
[ALARM IN] terminal during recording, the mode switches to the 2H (SP)
ALL
or 6H (EP) recording mode for realtime recording of the alarm event.
• Sensor recording: When an alarm signal is input to the rear panel's
OFF
AL SE 1
[ALARM IN] terminal in the Stop mode (Stop mode, Timer Recording
ALAR
Standby or Operating Off mode), recording starts in the 2H (SP) or 6H
SENS
(EP) mode.
ALL
OFF:
ALARM:
SENSOR: Sensor recording is executed.
ALL:
REC SPEED
[2H]
Selects the recording mode for alarm or sensor recording.
6H
2H: Records in the 2H (SP) mode.
6H: Records in the 6H (EP) mode.
2H
AL SE 2
6H
Function
starts again from the beginning. When set to "ON", the [REPEAT]
indication on the VCR's display lights.
The series recording and automatic recording with an external
signal functions are disabled.
The automatic recording function with an external signal is enabled.
is turned off.
reached during recording. A buzzer sounds when the menu switch
<END BUZ> on the <BUZZER/IN OUT> is set to "ON".
For more information on the relationship between the tape reel
counter value and the tape remaining time, refer to page 64.
Alarm or sensor recording is not executed.
Alarm recording is executed.
Both alarm and sensor recording are executed.
25
Advertisement
Table of Contents
