Clock Set; Tuner Set - JVC HR-V510E Instructions Manual

Clock Set

Turn on the recorder and the TV, and set your TV to its AV mode
or video channel.
A
Access Main Menu screen, then Clock Set screen
Press MENU. Press rt to place the pointer next to "CLOCK SET",
then press OK or e.
B
Set time, date and year
Press rt until the desired time appears,
then press OK or e. Set the date and year
in the same way.
Holding rt changes the time in
30-minute intervals, or changes the date
in 15-day intervals.
C
Start clock
Press MENU.

Tuner Set

Perform the following steps only if the tuner has not been set
correctly by Auto Set Up or Preset Download, or if you have
moved to a different area, or if a new station starts broadcasting in
your area.
The recorder needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area.
ATTENTION:
After you performed Auto or Manual Channel Set, please do
not disconnect the recorder from the power supply (AC)
immediately (in approximately 40 seconds). If the recorder is
disconnected from the AC outlet or if there is a power outage
within this period, some channels and station names might
not be stored correctly.
Under such circumtances, please check for the stored
channels and station names. If these are not stored correctly,
please perform Auto or Manual Channel set again.
Auto Channel Set
A
Access Main Menu screen, then Auto Channel Set screen
Press MENU. Press rt to place the pointer next to "AUTO CH
SET", then press OK or e.
B
Select your country
Press rt to place the pointer next to your country, then press OK
or e.
C
Select language
Press rt to place the pointer next to the desired language.
D
Perform Auto Channel Set
Press OK twice. When Auto Channel Set is
completed, "SCAN COMPLETED" is
displayed on the screen for about
5 seconds, then the Confirmation screen
appears.
E
Return to normal screen
Press MENU.
NOTES:
If no sound accompanies the picture or the audio sounds
unnatural on some channels, select the appropriate TV system
for those channels.
To delete stations with poor reception condition, refer to
"Deleting a channel" ( 14).
Manual Channel Set
Store channels that were not stored during Auto Set Up, Preset
Download or Auto Channel Set.
A
Access Main Menu screen, then Confirmation screen
Press MENU. Press rt to place the pointer next to "MANUAL
CH SET", then press OK or e.
B
Select position
Press rt w e until an open channel
position begins blinking, then press OK.
The Manual Channel Set screen appears.
C
Select band
Press rt to select CH (regular) or CC
(cable), then press e.
D
Input channel
Press the number keys to input the
channel number you want to store. Input
"0" before any single number entries.
You can set the desired station name
(maximum of 4 letters). To input the
station name, press e until the first
letter of the station name (ID) begins
blinking. Press rt to cycle through the characters, then press
e. Enter the remaining characters the same way (maximum of
4). After entering all characters, press OK.
• The characters available for the station name (ID) are A-Z, 0-9,
–, *, +, _ (space).
• If you make a mistake, press w until the incorrect character
begins blinking. Then enter the correct character by pressing
rt.
NOTE:
You can only check the station name (ID) in the individual
recording programme check screen.
If you have selected a country in Central
or Eastern Europe for country setting,
"TV SYSTEM" setting appears. When you
can see the picture but can hear no
audio, select appropriate TV system.
Press e until D/K or B/G blinks. Then press
rt to select D/K or B/G.
Major Countries/Areas
Austria, Denmark, Finland, Holland, Italy,
Norway, Spain, Switzerland, Sweden,
Germany, Egypt, Western Europe
China, Mongolia, Rumania, Bulgaria, Czech
Rep., Slovakia, Hungary, Poland, Russia,
Central or Eastern Europe
E
Store new channel
Press OK.
Repeat steps 2 – 5 as necessary.
F
Return to normal screen
Press MENU.
— 13 —
TV System
B/G
D/K