Timescan Audio - JVC HR-S9500EH Instructions Manual

TimeScan
Names of
special-effects
playback
-9x
Speed SP
Speed LP
Audio output
** Still mode cannot be engaged using the remote control's
pressing the PAUSE button.
** Smooth slow motion delivering an uninterrupted moving image without distortion.
The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (The display may be
distorted.)
To resume normal playback, press PLAY.
Picture and audio may become distorted when the recording speed changes. When this happens, resume normal playback
once, and then try using TimeScan again.
The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with
LP recordings.)
Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP
recordings, or depending on the tape being used.
Picture may appear distorted in comparison to normal playback.
When normal playback resumes from search (including TimeScan), still, slow motion or frame-by-frame playback, the picture
may jitter vertically momentarily depending on the type of TV being used.
In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal.
TimeScan sound quality will differ in comparison to normal playback.
When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 1.5x or
2x normal speed, the audio playback may be faster than normal.
Depending on the type of tape contents, the sound may not be clear during forward slow-motion playback.
Time Jog cannot be activated by pressing PAUSE for longer than 2 seconds.
When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.
Picture will be monochrome with an LP-recorded MESECAM tape during TimeScan.
When playing back an NTSC tape, the speeds differ from those listed above and are not shown on the TV screen.
TimeScan at -1/2x, 1/2x and 1.5x normal speed are not possible with a MESECAM tape.
The operations by the remote's JOG dial/SHUTTLE ring do not include TimeScan; noise will appear on the screen and audio
will not be output.
If you don't want to hear TimeScan audio, set "TIME SCAN AUDIO" to "OFF" (See below).

TimeScan Audio

The audio output can be set ON/OFF during TimeScan.
Select ON/OFF as required.
* The default setting is "ON".
1
Press MENU to access the Main Menu screen.
2 Move the highlight bar (pointer) to "MODE SET" by
pressing %fi, then press OK or
3
Move the highlight bar (pointer) to "TIME SCAN AUDIO"
by pressing %fi, then press OK or
"OFF".
4
Press MENU to return to the normal screen.
Reverse
Search Play
-7x -5x -3x -1x
-7x -3x
Audio is output.
.
to select "ON" or
Slow-Motion
*Still
(Time Jog**)
-1/2x 0
-1/2x 0
Audio is not Audio is
output. output.
HR-S9500E
MODE SET
AUTO TIMER
O. S. D.
B. E. S. T.
AUTO SP=LP TIMER
DIGITAL 3R
POWER SAVE
S-VHS
NEXT PAGE
[5∞] =
[MENU] : EXIT
PREVIOUS PAGE
EDIT
AV2 SELECT
COLOUR SYSTEM PAL/NTSC
TIME SCAN AUDIO
[5∞] =
[MENU] : EXIT
Forward
Slow-Motion
Play
(Time Jog**)
1/2x 1x 1.5x 2x 3x 5x 7x 9x
1/2x 1x 1.5x 2x
Audio is
Audio is output.
output.
or button. Still mode can be engaged by
HR-S9500EH
OFF AUTO TIMER
ON O. S. D.
ON B. E. S. T.
OFF AUTO SP=LP TIMER
ON
DIGITAL 3R
OFF S-VHS
AUTO EDIT
NEXT PAGE
[5∞] =
[MENU] : EXIT
PREVIOUS PAGE
OFF AV2 SELECT
VIDEO COLOUR SYSTEM PAL/NTSC
TIME SCAN AUDIO
ON
[5∞] =
[MENU] : EXIT
19
EN
Search
5x 9x
MODE SET
OFF
ON
ON
OFF
ON
AUTO
OFF
VIDEO
ON