Changing Remote Control Code - JVC HR-J781AM Instructions Manual

– Other Functions –
CABLE BOX OR SATELLITE
RECEIVER BRAND
JVC
AMSTRAD
BT
CANAL+
CANAL SATELLITE
D-box
ECHOSTAR
FINLUX
GALAXIS
GRUNDIG
HIRSCHMANN
ITT
JERROLD
KATHREIN
LUXOR
MASPRO
NOKIA
PACE
PANASONIC
PFT
PHILIPS
PHONOTREND
SALORA
SKYMASTER
TPS
VIDEOWAY
WISI
DVD BRAND
JVC
PANASONIC
PHILIPS
TOSHIBA

Changing Remote Control Code

This remote control is capable of transmitting two control codes;
one set to respond to A code control signals and another set to
respond to B code control signals. This remote control is preset to
send A code signals because your recorder is initially set to
respond to A code signals. You can easily modify your recorder
and the remote control to respond to B code signals. When using
two JVC recorders, set two recorders and their remote controls to
different codes, so that you can operate these recorders separately.
A
Set remote control code for remote control
A
Press and hold VCR.
B
Press the Number key "2".
C
Press OK, and release VCR.
The remote control now can transmit B code control signals.
B
Check remote control code for recorder
Press and hold PLAY (4) on the recorder for more than 5 seconds
while the recorder is turned off. The code currently set appears on
the display panel.
C
Change code for recorder
Press any key on the remote control. The recorder now responds
to B code control signals.
To set the remote control and the recorder back to A code
control signals, repeat the same procedure as shown above
except pressing the Number key "1" in step B of
To control two recorders with the same remote
control
You can control two JVC recorders by switching the remote
control code for the remote control between A and B (
keeping two recorders to different control codes.
To change only the remote control code for the remote control,
B B B B
DO NOT perform steps
CODE
72, 73,
60, 61, 62, 63, 92
72
81
81
85
51, 78, 79, 80, 82
68
69, 88
64, 65
64
68
01, 04, 06, 11, 12, 15, 28, 75
70, 71
68
70
68, 87
67, 86, 92
13, 14, 74
69
66, 84
69
68
69
83
03, 09, 22, 76, 77
64
CODE
55
58
56
57
1 1 1 1
.
C C C C
and .
Editing
You can use your recorder as the playback or recording deck. You
can use a camcorder as the source player and your recorder as the
recording deck. Refer also to the other components' instruction
manuals for connection and its operations.
A
Make connections
Example: When using this recorder as the source player
When using this recorder as the recording deck, connect this
recorder's AV input connectors to the AV output connectors on
the other recorder. If the source player is monaural, connect the
audio output connector on the source player to the left audio
input connector on this recorder.
B
Load cassettes
Insert the playback cassette into the source player and the cassette
to be recorded on into the recording deck.
C
Select input mode on recording deck
Select the correct external input on the recording deck. Press AUX
or PR+/–.
On this recorder (when using this recorder as the recording deck);
Select "L-1" — when connecting the other recorder to the AV
input connectors on the rear panel.
Select "F-1" — when connecting the other recorder to the AV
input connectors on the front panel.
D
Select edit mode
Set the edit mode to "ON" for the recorders if such a mode is
equipped.
On this recorder, set "PICTURE CONTROL" to "EDIT".
E
Start playback
Press PLAY (
F
Start recording
Press REC (
7
When the JVC camcorder is equipped with the Master Edit
Control, you can control the VCR from the camcorder. Connect
the mini-plug cable (not supplied with this VCR) between the
A A A A
step ),
PAUSE terminal and the EDIT connector on the camcorder.
This recorder (for playback)
To AUDIO/VIDEO OUT
AV cable
(not supplied)
To AV input
Another recorder (for recording)
) on the source player.
4
) on the recording deck.