Playback; Basic Playback; Playback Features - JVC 0203-AH-CR-LG Instruction Manual

Playback

Basic Playback

Turn on the TV and select the AV mode or video channel.
A
Load a cassette
Make sure the window side is
up, the rear label side is facing
you and the arrow on the front of
the cassette is pointing towards
the recorder.
Do not apply too much pressure when inserting.
The recorder turns on, and the counter is reset, automatically.
If the cassette's record safety tab has been removed, playback
begins automatically.
B
Start playback
Press 4.
If the tape reaches its end during playback, the recorder stops
playback, rewinds the tape and ejects the cassette, then enters
the standby mode automatically.
During playback
Press 8 on the remote
control.
Press 9.
The recorder enters Pause mode after moving 2 or 3 frames.
If there is vertical jitter, use the
Press 4 to resume normal playback.
Still picture playback stops automatically after about 5 minutes
to protect the heads.
Press 9 to pause, then press 9 repeatedly.
Press 4 to resume normal playback.
During still picture, press e to start forward slow motion
playback. If you press 9, still picture resumes.
During playback or still, press and hold 9 for 2 seconds, then
release it. Press 4 or 9 again to resume playback or still picture.
Slow motion playback stops automatically after about 30
seconds to protect the heads, then normal playback resumes.
Press 3 or 5.
Press 4 to resume normal playback.
High-speed search stops automatically after about 3 minutes to
protect the heads, then normal playback resumes.
Press w or e repeatedly.
Press 4 to resume normal playback.
Each time you press w or e, the playback speed changes. To
decrease the speed during picture search, press the opposite
direction button repeatedly.
If there is vertical jitter, use the
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback mode,
the picture will be distorted
the noise bars will appear
there will be a loss of color with an LP-recorded tape (HR-
V505/V506/V507E only)
Press 0 on the recorder.
to correct the picture.
to correct the picture.
Reverse
search Reverse play
2 steps
When the tape is not running
Press 3 or 5.
If you press and hold 3 or 5 during rewinding or fast-
forwarding, you can see the picture on the screen. Releasing it
cancels the picture search and resume rewinding and fast-
forwarding.
Press .
You can also eject the cassette when the recorder is standby
mode.
Press 1 on the remote
control. The recorder enters
the standby mode.

Playback Features

Adjusting tracking condition
When a new cassette is loaded, the recorder enters the automatic
tracking mode.
If automatic tracking cannot eliminate noises well during
playback, adjust the tracking manually.
Press and hold
Selecting Soundtrack (HR-V505/V506/V507E
only)
Your recorder is capable of recording four soundtracks (STEREO,
LEFT, RIGHT and MONO) and plays back the one you select. Set
"AUDIO" to the appropriate mode. (
NOTE:
(
Rewind Power Off
When the tape is not running, press 3, then press 1. "REW"
blinks on the screen. The recorder enters the standby mode
automatically after rewinding the tape.
Ez (Easy) Power Off
During playback, press
rewinds the tape and ejects the cassette, then enters the standby
mode automatically.
Skipping unwanted portions
— Skip Search
Press once to 6 times during playback. Each press
initiates a 30-second period of high-speed playback (up to
3 minutes). When the specified portion of the tape is skipped,
normal playback resumes automatically. To return to normal
playback during Skip Search, press 4.
— 10 —
Forward
slow motion Normal play
1 step
Press 0 on the recorder.
Press 1 on the recorder.
The recorder turns off.
or to eliminate the noises.
5)
. The recorder stops playback,
Forward
search
2 steps