Table of Contents
Advertisement
Booklet 3.4 RNS 510
Traffic programme (TP) function
If the traffic programme function is turned on, you will hear traffic announce-
ments made by a TP station during active audio mode. The audio mode will be
paused for the duration of an announcement.
Fig. 11 Activating the TP function.
Turning the traffic programme (TP) on
or off
- Press the
[RADIO)
function
selection
button to open the
RADIO
main menu.
- Touch the
I
Extra,)
function key.
- In the popup window which open,
touch => fig. 11
cm
briefly to turn the
traffic programme function on or
off.
A tick
in
the checkbox
~
indicates that the TP
function is already active. Alternatively,
the TP function can
also
be turned on or
offin the RADIO
settings
=> page 121.
The display
"TP"
in
conjunction
with
a station
name (e.g. in the
station
list or memory list) in-
dicates a TP station.
Whatever radio station you happen to
be
lis-
tening to, an additional receiver section in the
unit ensures that a TP
station is always
received
so long as the TP function is turned
on.
"TP" in the top right
corner of
the
screen
indi-
cates that the TP function is ready for
use
=> fig. 12.
If no TP station
can
be received
at
any time,
e.g.
because radio reception
is
generally
poor,
then
18
Function selection button RADIO
Fig. 12 Incoming traffic announcement.
"No
TP" is displayed instead
of"TP". Note
that
multi-storey car parks, tunnels. high buildings
or mountains can interrupt
or even
completely
block radio signals.
Incoming traffic announcement
A
popup window opens
=>
fig.
12 while a traffic
announcement is being played
.
!fyou wish to interrupt the
announcement,
touchlcancellin the Traffic
annoullcement
popup
window. The TP function remains in standby
(display: TP) and the next traffic announcement
will be made in the current
audio
mode.
Touch
IDeact TPJ to permanently deactivate the TP func-
tion.
The unit wiU be switched to predefined
settings
for volume, balance and fader for the
duration of
the announcement. You can change these
set-
tings while the traffic announcement is being
made.
Adjust the volume during a traffic announce-
ment using the volume control.
Press
thelTONEJ
function selection button to adjust the
settings
for balance during a traffic announcement
=>
page 55.
In the
volume
presets
you can also
specify the
volume
with
which
traffic
announcements are
made
=>
page
55.
~
Booklet 3.4 RNS 510
Function selection buHon MEDIA
General information on CDIDVD mode
Audio CDs (CD-A) and
audio
DVDs, MP3 CDs
and MP3 DVDs, as well as video DVDs
can
be
played in the internal
CD
I
DVD drive.
CD cannot be read
If a CD/DVD is loaded
which
the player cannot
read, the following messages appear briefly "CD
error. Please check CD." or
"Incorrect
data format.
Unable to read file."
and
the
CD/DVD is
ejected
after a few seconds.
Ifthe CD/DVD is not removed from the tray
within 10 seconds, it is retracted
again
to prevent
damage.
&.
WARNING
•
The CD player is a class
1
laser product.
When the CD player is opened, there is a risk of
injury caused by the invisible laser beams es-
caping from the unit.
• The CD player contains no parts which you
can service or repai.r by yourself. You should
therefore contact an authorised dealer if there
is a mechanical fault or if a repair is required.
CD
Caution
•
Inserting a second CD/DVD while an in-
serted CD/DVD is being
ejected can
destroy the
CD/DVD drive in the unit. Note that it takes a
few seconds to eject the
CDIDVD after
pressing
the Eject button
@.
The protective barrier in
front of the CD/DVD
slot
is
opened while
this
is
happening. You must
wait until
the
CD/DVD is
ejected before trying to insert a new
CD/DVD.
•
If the CD/DVD drive has a mechanical fault
or
if a CD/DVD has been incorrectly
or
not fully
loaded,
the message
"
CD
error.
Please check
CD:
'
and then
"OVD
drive
error"
a
ppears
on
the
screen.
Check the
CD/DVD and
then insert it
properly in the drive. If the message
"DVD
drive
error" reappears, please contact your
Volkswagen Service
=>
&
.
•
You wiU be unable to insert
any
more CDs or
DVDs if the temperature inside the unit is too
high. The unit will switch on in the last used
mode.
•
Refer to the notes on handling CDs
and
DVDs
=> page 54, "Handling data media (CDs and
DVDs)".
[l)
Note
•
Ifthe@functionkeYisshownasinactive,it
means that no audio CD/DVD is currently
loaded or that a loaded audio CD/DVD
cannot
be read.
•
You might not be able to play copy-protected
CDs or CD-Rs, CD-RWs and DVD-RWs which
you
have burned yourself.
•
WMAaudio files (Windows Media
Audio)
can
also be played on the unit and stored on the hard
drive (HDD) provided they
are
not copyright
protected by the DRM process (Digital Rights
Management). Their operation
and
perform-
ance on the unit is the same
as
for MP3 com-
pressed audio files, and is therefore not de-
scribed separately here.
•
Please also refer to the
additional
informa-
tion on MP3 mode
=>
page
28.
•
Please observe the
copyright
laws
applicable
in your
country.
•
The DVD drive in this unit
uses
a
Dolby
Dig-
ital® audio coding
system
and MLP
Lossless®
for
optimal playback
qualiry,
including for
audio
DVDs that conform to this
standard. "Dolby®",
"MLP Lossless®" and the double-D
symbol are
registered trade marks of Dolby Laboratories®.
•
The surround
sound
of
a
DVD is converted
using
"DTS®"
and
"DTS
2.0®"
and reproduced
in
optimal stereo qualiry.
"DTS®" and "DTS
2.0®"
are registered trade marks
ofDTS,
Inc.
~
Function selection button MEDIA
19
Hide quick links:
Advertisement
Table of Contents
