Page 1
COMPACT COMPONENT SYSTEM SYSTEME DE COMPOSANTS COMPACT MX-GB6 —Consists of CA-MXGB6 and SP-MXGB6 —Composé du CA-MXGB6 et SP-MXGB6 MX-GB5 —Consists of CA-MXGB5 and SP-MXGB5 —Composé du CA-MXGB5 et SP-MXGB5 SP-MXGB6 SP-MXGB5 INSTRUCTIONS MANUEL D’INSTRUCTIONS CA-MXGB6 SP-MXGB6 CA-MXGB5 SP-MXGB5 For Customer Use: Enter below the Model No.
Warnings, Cautions and Others Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated...
Page 3
For Canada/pour le Canada CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
Page 4
Introduction We would like to thank you for purchasing one of our JVC products. Before operating this unit, read this manual carefully and thoroughly to obtain the best possible performance from your unit, and retain this manual About This Manual This manual is organized as follows: •...
Contents Location of the Buttons and Controls ... 3 Getting Started ... 6 Common Operations ... 9 Listening to the Radio ... 12 Playing Back CDs ... 13 Playing Back Tapes ... 20 Recording ... 21 Using the Timers ... 23 Maintenance ...
Remote Control When using the remote control, point it at the remote sensor on the front panel. Remote Control 1 BEEP ON/OFF button (11) 2 SLEEP button (25) 3 Number buttons (12, 16) 4 TAPE A 3 (play) button (9, 20) Pressing this button also turns on the unit.
Getting Started Unpacking After unpacking, check to be sure that you have all the following items. The number in the parentheses indicates the quantity of the pieces supplied. • AM loop antenna (1) • FM antenna (1) • Remote control (1) •...
• Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord. Connecting Speakers For MX-GB6: DO NOT carry the speaker by holding the tube duct (on the top of the speaker). 2, 3...
Connecting Other Equipment You can connect audio equipment—used only as a playback device. • DO NOT connect any equipment while the power is on. • DO NOT plug in any equipment until all connections are complete. To connect audio equipment Stereo mini plug cord (not supplied) Audio equipment To audio output...
Common Operations Turning On or Off the Power To turn on the unit, press STANDBY/ON so that the standby lamp goes off. To turn off the unit (on standby), press STANDBY/ON again so that the standby lamp lights up. A little power is always consumed even while the unit is on standby.
Adjusting the Volume You can adjust the volume level only while the unit is turned This function only affects the playback sound, not your recording. Turn the VOLUME control clockwise to increase the volume or counterclockwise to decrease it. • The volume level can be adjusted in 32 steps (VOL MIN, VOL 1 —...
Selecting the Sound Modes This function only affects the playback sound, not your recording. You can select one of the 6 preset sound modes (3 surround modes and 3 SEA—Sound Effect Amplifier—modes). To select the sound modes, press up the SOUND MODE control repeatedly until the sound mode you want appears on the display.
Listening to the Radio Tuning in to a Station—Auto Search Press FM/AM. The unit automatically turns on and tunes in to the previously tuned station (either FM or AM). • Each time you press the button, the band alternates between FM and AM. Start searching for stations.
Playing Back CDs This unit has been designed to playback the following CDs: • Audio CD • CD-R (CD-Recordable) • CD-RW (CD-ReWritable) • MP3 disc (MP3 files recorded on a CD-R or CD-RW)* When playing a CD-R or CD-RW • User-edited CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be played back when they are already “finalized.”...
Page 17
• Each time you press the button, the indication on the display changes as follows: ALL DISC 1 DISC (initial setting) REPEAT ALL DISC* REPEAT 1 See page 19. Press one of the disc number buttons (CD1, CD2 or CD3) for the disc you want to start to play from.
One Disc play When 2 or 3 CDs are loaded on the disc trays, you can select one particular disc to be played back. On the unit ONLY: Load CDs. • If the current playing source is not the CD player, press CD 6, then 7 before going to the next step.
Page 19
For MP3 disc: When the MP3 playback mode is the TRACK mode (See also page 17.) Press ¢ or 4 before or during playback. • ¢: Skips to the beginning of the next or succeeding tracks. • 4: Goes back to the beginning of the current or previous tracks.
Changing the MP3 Playback Mode When playing an MP3 disc, you can choose the playback mode of the MP3 disc as follows: • TRACK mode: The unit recognizes only tracks (files). You can play an MP3 disc like an Audio CD. •...
Programming the Playing Order of the Tracks —–Program Play You can arrange the order in which the tracks play before you start playing. You can program up to 32 tracks. • To use Repeat play (see page 19) for Program play, press REPEAT after starting Program play.
Playing at Random—–Random Play The tracks of the selected CD will play at random. • To use Random play, you have to cancel Program play. On the unit ONLY: Load a CD. Press one of the disc number buttons (CD1, CD2, and CD3) for the disc you want to play, then press 7.
Playing Back Tapes Playing Back a Tape Press 0 for the deck you want to use. For Deck A Put a cassette in, with the exposed part of the tape down and the side you want to play facing front. •...
Recording IMPORTANT: • It may be unlawful to record or play back copyrighted material without the consent of the copyright owner. • The recording level is automatically set correctly, so it is not affected by the VOLUME, the SUBWOOFER LEVEL, the RHYTHM AX, and the SOUND MODE controls.
Dubbing Tapes On the unit ONLY: Press TAPE A 3, then 7. Put the source cassette in deck A, and a recordable cassette into deck B. Press DUBBING. Dubbing starts. “DUBBING” appears, and the REC (recording) indicator lights up on the display. •...
Using the Timers There are three timers available—Daily Timer, Recording Timer, and Sleep Timer. Before using the timers, you need to set the clock built in the unit. (See “Setting the Clock” on page 9.) Using Daily Timer With Daily Timer, you can wake to your favorite music or radio program.
Select the preset station number. Press ¢ or 4 to select the preset station number, then press SET/DISPLAY. The unit enters volume setting mode. Press ¢ or 4 to set the volume level. • You can select the volume level from VOL MIN, VOL 1 —...
Set the on-time you want the unit to turn on. 1) Press ¢ or 4 to set the hour, then press SET/DISPLAY. 2) Press ¢ or 4 to set the minute, then press SET/DISPLAY. “OFF TIME” appears for 2 seconds, then the unit enters off- time setting mode.
Maintenance To get the best performance of the unit, keep your discs, tapes, and mechanism clean. Cleaning the unit • Stains on the unit Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.
Troubleshooting If you are having a problem with your unit, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person, such as your dealer, for service.
Specifications Amplifier section—CA-MXGB6 Output Power SUBWOOFERS : 170 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 10% total harmonic distortion. MAIN SPEAKERS: 80 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no more than 10% total harmonic distortion.
Page 32
Introduction Nous vous remercions d’avoir acheté un de nos produits JVC. Avant d’utiliser l’appareil veuillez lire entièrement et attentivement ce mode d’emploi afin d’obtenir les meilleures performances possibles, et conservez ce mode d’emploi à titre de référence. À propos de ce mode d’emploi Ce mode d’emploi est organisé...
Page 33
Table des matières Emplacement des touches et des commandes ... 3 Pour commencer ... 6 Fonctionnement commun ... 9 Écoute de la radio ... 12 Lecture d’un CD ... 13 Lecture d’une cassette ... 20 Enregistrement ... 21 Utilisation des minuteries ... 23 Entretien ...
Télécommande Lors de l’utilisation de la télécommande, dirigez-la sur le capteur de télécommande du panneau avant. Télécommande 1 Touche BEEP ON/OFF (11) 2 Touche SLEEP (25) 3 Touches numériques (12, 16) 4 Touche TAPE A 3 (lecture) (9, 20) Appuyer sur cette touche met aussi l’appareil sous tension. 5 Touche VOLUME + (10) 6 Touche FM/AM (9, 12) Appuyer sur cette touche met aussi l’appareil sous tension.
Pour commencer Déballage Après le déballage, vérifiez que tous les éléments suivants sont présents. Le nombre entre parenthèses indique la quantité de pièces fournie. • Antenne cadre AM (1) • Antenne FM (1) • Télécommande (1) • Piles (2) Si quelque chose manquait, consultez votre revendeur immédiatement.
• Éloignez les antennes des parties métalliques de l’appareil, des cordons de connexion et du cordon d’alimentation secteur. Connexion des enceintes Pour le MX-GB6: NE PORTEZ PAS les enceintes en les tenant par la gaine (au sommet des enceintes). 2, 3 Cordon d’enceinte...
Connexion d’un autre appareil Vous pouvez connecter un appareil audio—utilisé uniquement comme appareil de lecture. • NE RÉALISEZ AUCUNE connexion quand l’appareil est sous tension. • NE BRANCHEZ AUCUN appareil au secteur avant que toutes les connexions soient terminées. Pour connecter un appareil audio Cordon à...
Fonctionnement commun Mise sous ou hors tension de l’appareil Pour mettre l’appareil sous tension, appuyez sur STANDBY/ON de façon que le témoin d’attente s’éteigne. Pour mettre l’appareil hors tension, appuyez sur STANDBY/ON de façon que le témoin d’attente s’allume. Une petite quantité d’énergie est consommée en permanence même quand l’appareil est en attente.
Ajustement du volume Vous pouvez ajuster le niveau de volume uniquement quand l’appareil est sous tension. Cette fonction n’affecte que le son de lecture et non pas votre enregistrement. Tournez le réglage VOLUME dans le sens des aiguilles d’une montre pour augmenter le volume ou dans le sens contraire pour le diminuer.
Sélection des modes sonores Cette fonction n’affecte que le son de lecture et non pas votre enregistrement. Vous pouvez choisir un des 6 modes sonores préréglés (3 modes Surround et 3 modes SEA—Amplificateur d’effet sonore). Pour choisir les modes sonores, poussez répétitivement vers le haut le réglage SOUND MODE jusqu’à...
Écoute de la radio Accord ‘une station—Recheche automatique Appuyez sur FM/AM. L’appareil se met automatiquement sous tension et accord automatiquement la dernière station écoutée (FM ou AM). • Chaque fois que vous appuyez sur la touche, la bande alterne entre FM et AM. Démarrez la recherche des stations.
Lecture d’un CD Cet appareil est conçu pour reproduire les types de CD suivants: • CD audio • CD-R (CD enregistrable) • CD-RW (CD réinscriptible) • Disque MP3 (fichiers MP3 enregistrés sur un CD-R ou CD-RW)* Lors de la reproduction d’un CD-R ou CD-RW •...
Page 45
• Chaque fois que vous appuyez sur la touche, l’indication de l’affichage change comme suit: ALL DISC 1 DISC (Réglage initial) REPEAT ALL DISC* REPEAT 1 Voir page 19. Appuyez sur la touche de numéro de disque (CD1, CD2 ou CD3) du disque à partir duquel vous souhaitez commencer la lecture.
Lecture d’un seul disque Quand 2 ou 3 CD sont en place sur le plateau à disque, vous pouvez choisir le disque que vous souhaitez reproduire. Sur l’appareil UNIQUEMENT: Insérez les CD. • Si la source de lecture actuelle n’est pas le lecteur de CD, appuyez sur CD 6, puis sur 7 avant de passer à...
Page 47
Pour les disques MP3: Quand le mode de lecture MP3 est réglé sur le mode TRACK (Référez-vous aussi à la page 17.) Appuyez sur ¢ ou 4 avant ou pendant la lecture. • ¢: Saute au début d’une des plages suivantes. •...
Changement du mode de lecture MP3 Lors de la lecture d’un disque MP3, vous pouvez choisir le mode de lecture du disque MP3 de la façon suivante: • Mode TRACK: L’appareil reconnaît uniquement les plages (fichiers). Vous pouvez reproduire un disque MP3 de la même façon qu’un CD audio.
Programmation de l’ordre de lecture des plages —–Lecture programmée Vous pouvez arranger l’ordre dans lequel vous souhaitez reproduire les plages. Vous pouvez programmer 32 plages maximum. • Pour utiliser la lecture répétée (voir page 19) pour la lecture programmée, appuyez sur REPEAT après avoir démarré la lecture programmée.
Lecture dans un ordre aléatoire —Lecture aléatoire Les plages du CD choisi sont reproduites aléatoirement. • Pour utiliser le mode de lecture aléatoire, vous devez annuler d’abord le mode de lecture programmée. Sur l’appareil UNIQUEMENT: Insérez un CD. Appuyez sur la touche de numéro de disque (CD1, CD2 et CD3) du disque que vous souhaitez reproduire,...
Lecture d’une cassette Lecture d’une cassette Appuyez sur 0 de la platine que vous souhaitez utiliser. Pour la platine A Insérez une cassette avec la partie exposée de la bande dirigée vers le bas et la face que vous souhaitez reproduire dirigée vers l’avant. •...
Enregistrement IMPORTANT: • Notez qu’il peut être illégal d’enregistrer ou de reproduire un matériel protégé par des droits d’auteur sans la permission du propriétaire des droits. • Le niveau d’enregistrement est réglé correctement automatiquement et n’est pas affecté par les réglages VOLUME, SUBWOOFER LEVEL, RHYTHM AX et SOUND MODE.
Copie de cassettes Sur l’appareil UNIQUEMENT: Appuyez sur TAPE A 3, puis sur 7. Mettez la cassette source dans la platine A et une cassette enregistrable dans la platine B. Appuyez sur DUBBING. La copie démarre. “DUBBING” apparaît et l’indicateur REC (enregistrement) s’allume sur l’affichage.
Utilisation des minuteries Il y a trois minuteries disponibles—la minuterie quotidienne, d’enregistrement et d’arrêt. Avant d’utiliser les minuteries, vous devez régler l’horloge intégrée à l’appareil. (Voir “Réglage de l’horloge” à la page 9.) Utilisation de la minuterie quotidienne Avec la minuterie quotidienne, vous pouvez vous réveiller au son de votre musique ou émission de radio préférée.
Choisissez un numéro de station préréglée. Appuyez sur ¢ ou 4 pour choisir le numéro de station préréglé, puis appuyez sur SET/ DISPLAY. L’appareil entre en mode de réglage du volume. Appuyez sur ¢ ou 4 pour régler le niveau du volume.
Réglez l’heure à laquelle vous souhaitez que l’appareil se mette sous tension. 1) Appuyez sur ¢ ou 4 pour régler les heures, puis appuyez sur SET/DISPLAY. 2) Appuyez sur ¢ ou 4 pour régler les minutes, puis appuyez sur SET/DISPLAY. “OFF TIME”...
Entretien Pour obtenir les meilleures performances de votre appareil, gardez propres les disques, les cassettes et le mécanisme. Nettoyage de l’appareil • Tâches sur l’appareil Frottez-les avec un chiffon doux. Si l’appareil est très sale, frottez avec un chiffon imprégné d’une solution détergente neutre et bien essoré...
Guide de dépannage Si vous des problèmes avec votre appareil, cherchez d’abord une solution dans cette liste avant d’appeler un réparateur. Si vous ne pouvez pas résoudre le problème avec les conseils donnés ici, ou si l’appareil est physiquement endommagé, appelez une personne qualifiée, telle que votre revendeur, pour faire réparer l’appareil.
Spécifications Section de l’amplificateur—CA-MXGB6 Puissance de sortie SUBWOOFERS : 170 W par canal, min. RMS, entraîné sur 6 Ω à 63 Hz avec moins de 10% de distorsion harmonique totale. MAIN SPEAKERS: 80 W par canal, min. RMS, entraîné sur 4 Ω...