Dell Latitude D600 User Manual page 81

Enable the Pointing Device option in the system setup program. If the problem persists,
Bad command or file name —
pathname.
Cache disabled due to failure —
CD drive controller failure —
Data error —
Decreasing available memory —
necessary, replace them. See
Disk C: failed initialization —
Floppy drive 0 seek failure —
described in "Using the Dell
Diskette read failure —
Diskette subsystem reset failed —
Diagnostics."
Diskette write-protected —
Drive not ready —
push the floppy disk all the way into the drive until the eject button pops out. Or,
Error reading PCMCIA card —
Extended memory size has changed —
Restart the computer. If the error appears again,
Gate A20 failure —
General failure —
example, Printer out of paper. Take the appropriate action.
Hard-disk drive configuration error —
the computer from a bootable floppy disk or CD. Then turn off the computer, reinstall the hard drive, and restart the computer. Run the Hard-
Disk Drive tests as described in
Hard-disk drive controller failure 0 —
hard drive, and boot the computer from a bootable floppy disk or CD. Then turn off the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the Hard-Disk Drive tests as described in
Hard-disk drive failure —
and boot the computer from a bootable floppy disk or CD. Then turn off the computer, reinstall the hard drive, and restart the computer. If
the problem persists, try another drive. Run the Hard-Disk Drive tests as described in
Hard-disk drive read failure —
a bootable floppy disk or CD. Then turn off the computer, reinstall the hard drive, and restart the computer. If the problem persists, try
another drive. Run the Hard-Disk Drive tests as described in
Insert bootable media —
Downloaded from www.Manualslib.com
Ensure that you have spelled the command correctly, put spaces in the proper place, and used the correct
The primary cache internal to the microprocessor has failed.
The CD drive does not respond to commands from the computer. See
The floppy or hard drive cannot read the data. See
One or more memory modules may be faulty or improperly seated. Reseat the memory modules and, if
"Adding Memory."
The hard drive failed initialization. Run the Hard-Disk Drive tests as described in
The system configuration information may not match the hardware configuration. Run the Diskette tests as
Diagnostics."
The floppy disk may be defective. If the drive access light turns on, try a different disk. See
The floppy drive controller may be faulty. Run the Diskette tests as described in
Because the floppy disk is write-protected, the operation cannot be completed. Slide the write-protect notch.
The operation requires a floppy disk in the drive or a hard drive in the bay before it can continue. Insert a floppy disk, or
The computer cannot identify the PC Card. Reinsert the card or try another PC Card.
The amount of memory recorded in NVRAM does not match the memory installed in the computer.
contact
A memory module may be loose. Reinstall the memory modules
The operating system is unable to carry out the command. The message is usually followed by specific information—for
The computer cannot identify the drive type. Turn off the computer,
"Using the Dell Diagnostics."
The hard drive does not respond to commands from the computer. Turn off the computer,
The hard drive does not respond to commands from the computer. Turn off the computer,
The hard drive may be defective. Turn off the computer,
The operating system is trying to boot to a nonbootable floppy disk or CD. Insert a bootable floppy disk or CD.
manuals search engine
contact Dell.
Contact
"Drive Problems."
install a hard drive
Dell.
and, if necessary, replace them.
"Using the Dell
remove the hard
"Using the Dell Diagnostics."
Dell.
"Drive Problems."
"Using the Dell Diagnostics."
"Drive Problems."
"Using the Dell
in the hard drive bay.
remove the hard drive, and boot
remove the
"Using the Dell Diagnostics."
remove the hard drive,
Diagnostics."
drive, and boot the computer from