Korg pa 900 User Manual page 385

41: 2Voice Resonator
This effect resonates the input signal at a specified pitch. You can
set the pitch, output level, and pan settings for two resonators
individually. You can control the resonance intensity via an LFO.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Resonator
Trim
+
Resonance
Resonator
Trim
Right
D Invert: On/Off
-mod
LFO
Control Mode
Manual
Manual, LFO,
Control Mode
D-mod
a
LFO/D-mod
Off, On
Invert
LFO Frequency
0.02...20.00
[Hz]
b
D-mod Src Off...Tempo
MIDI Sync Off, On
MIDI,
BPM 40.00...
c
300.00
Base Note r...w
Times x1...x32
Mod. Depth –100...+100
d
Trim 0...100
Voice1: Pitch C0...B8
e Fine [cents] –50...+50
Level 0...100
Voice1:
–100...+100
Resonance
f High Damp [%] 0...100
L6...L1, C,
Pan
R1...R6
Voice2: Pitch C0...B8
g Fine [cents] –50...+50
Level 0...100
Voice2:
–100...+100
Resonance
h High Damp [%] 0...100
L6...L1, C,
Pan
R1...R6
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src Off...Tempo
Amt –100...+100
FX Amt
High Damp
Level Pan
Level Pan
High Damp
FX Amt
Pitch, Fine [cents]
Switches the controls of resonance
intensity
Reverses the Voice 1 and 2 control
when LFO/D-mod is selected
Sets the speed of the LFO
Selects the modulation source that
controls resonance intensity
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the amount of resonance
intensity control via LFO/D-mod
Sets the input level at the resonator
Sets the voice1 Pitch for resonance
Fine-adjusts the voice 1 pitch for
resonance
Sets the Voice1 output level
Sets the intensity of resonance
when Control Mode = Manual
Sets the damping amount of
resonant sound in the high range
Sets the Voice1 stereo image
Sets the voice 2 Pitch for resonance
Fine-adjusts the voice 2 pitch for
resonance
Sets the Voice2 output level
Sets the intensity of resonance
when Control Mode = Manual
Sets the damping amount of
resonant sound in the high range
Sets the Voice2 stereo image
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
Modulation and Pitch Shift (Mod./P.Shift)
a: Control Mode
f: Voice 1: Resonance
h: Voice 2: Resonance
This parameter determines the resonance intensity.
When "Control Mode" = Manual, the "Resonance" parameter
sets the intensity of resonance. If the "Resonance" parameter has
a negative value, harmonics will be changed, and resonance will
occur at a pitch one octave lower.
When "Control Mode" = LFO, the intensity of resonance varies
according to the LFO. The LFO sways between positive and neg-
ative values, causing resonance to occur between specified
pitches an octave apart in turn.
When "Control Mode" = D-mod, the resonance is controlled by
the dynamic modulation source. If JS X or Ribbon is assigned as
the modulation source, the pitch an octave higher and lower can
be controlled, similar to when LFO is selected for Control Mode.
a: LFO/D-mod Invert
When "Control Mode" = LFO or D-mod, the controlled phase of
either Voice 1 or 2 will be reversed. When the resonance pitch is
set for Voice 1 (Resonance has a positive value), Voice 2 will res-
onate at a pitch an octave below (Resonance has a negative
value).
f: Voice 1: Pitch
f: Fine [cents]
h: Voice 2: Pitch
h: Fine [cents]
The Pitch parameter specifies the pitch of resonance by note
name. The "Fine" parameter allows for fine adjustment in steps
of cents.
g: High Damp [%]
i: High Damp [%]
This sets the amount of damping amount for the high frequen-
cies of the resonant sound. Lower values create a metallic sound
with a higher range of harmonics.
Effects
381