Philips M32 107T4 GS_3 Service Manual
  1. Manuals
  2. Brands
  3. Philips Manuals
  4. Monitor
  5. M32 107T4 GS_3
  6. Service manual
Philips M32 107T4 GS_3 Service Manual

Philips M32 107T4 GS_3 Service Manual

17" auto scan colour monitor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
17" Auto scan Colour Monitor
DDC/Power saving/MPR II/TCO
Description
Important Safety Notice ------------------------------- 2
Technical Data ------------------------------------------ 3
Front control & OSD------------------------------------ 4
OSD menu tree------------------------------------------ 5
OSD Adjustments-----------------------------------6~12
Troubleshooting----------------------------------------12
Service mode--------------------------------------------13
Warning and Notes ------------------------------------ 14
Mechanical Instructions ------------------------- 15~17
Wiring Diagram------------------------------------------18
Hex Data of DDC2B--------------------------------19 ~22
DDC Instructions -----------------------------------23~27
Electrical Adjustments --------------------------- 28~ 30
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC
EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING.
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by BCU Monitors
Printed in Taiwan

TABLE OF CONTENTS

Description
Page
Block Diagram ------------------------------------------32
Video Panel C.B.A.(A) --------------------------------34
Main Panel-Deflection (B) Schematic Diagram --35
Main Panel C.B.A.(B,C)-------------------------------36
Power Supply (C) Schematic Diagram-------------37
Key Control Panel (D) Schematic Diagram -------38
Key ControlPanel C.B.A. (D) ------------------------39
Repair Tips ----------------------------------------------40
Exploded View------------------------------------------41
Recommended parts list------------------------------42
Spare parts list------------------------------------- 43~45
Repair flow chart----------------------------------- 46~53
General Product Specification-------------------54~83
General Troubleshooting Guide----------------84~106
LightFrame for Windows----------------------- 107~110
SAFETY NOTICE
©
Copyright reserved
Subject to modification
Chassis :M32
M32 107T4 GS_3
107T41/00C
Horizontal frequencies
30 - 71 kHz
Aug. 08, 2002
Page
3138 106 10218

Advertisement

Table of Contents
loading

Related Manuals for Philips M32 107T4 GS_3

Summary of Contents for Philips M32 107T4 GS_3

  • Page 1: Table Of Contents

    17" Auto scan Colour Monitor Chassis :M32 M32 107T4 GS_3 DDC/Power saving/MPR II/TCO 107T41/00C Horizontal frequencies 30 - 71 kHz TABLE OF CONTENTS Description Page Description Page Block Diagram ------------------------------------------32 Important Safety Notice ------------------------------- 2 Video Panel (A) Schematic Diagram ---------------33 Technical Data ------------------------------------------ 3 Video Panel C.B.A.(A) --------------------------------34...

  • Page 2: Important Safety Notice

    REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR evaluation. Accordingly, a servicer who uses a service PART NUMBERS IN THE PARTS LIST SECTION OF THIS procedure or tool which is not recommended by PHILIPS SERVICE MANUAL. must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

  • Page 3: Technical Data

    Pin assignment : ® This monitor is ENERGY STAR compliant. ® As an ENERGY STAR Partner, PHILIPS has determined that ® this product meets the ENERGY STAR guidelines for energy efficiency The 15-pin D-sub connector(male) of the signal cable : ENERGY STAR is a U.S.

  • Page 4: Front Control & Osd

    Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor.

  • Page 5: Osd Menu Tree

    OSD menu tree M32 107T4 GS_3 Go to cover page The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments.

  • Page 6: Osd Adjustments

    OSD Adjustments M32 107T4 GS_3 Go to cover page The OSD Controls LANGUAGE The ON SCREEN DISPLAY shows its settings in one of five languages. The default is English, but you can select French, Spanish, German, or Italian. BRIGHTNESS To adjust your screen's brightness, follow the steps below. Brightness is 1) Press the button on the monitor.
  • Page 7 OSD Adjustments (Continued) M32 107T4 GS_3 Go to cover page ZOOM 3) Press the button. The ADJUST HORIZONTAL window appears. ADJUST POSITION should be highlighted. ZOOM increases or decreases the size of the images on your screen. To adjust the ZOOM follow the steps below.
  • Page 8 OSD Adjustments (Continued) M32 107T4 GS_3 Go to cover page 2) Press the button until ADJUST SHAPE is highlighted. 2) Press the button until ADJUST VERTICAL is highlighted. 3) Press the button. The ADJUST SHAPE window appears. 3) Press the button.
  • Page 9 OSD Adjustments (Continued) M32 107T4 GS_3 Go to cover page Smart Help After returning to MAIN CONTROLS . . . 7) When the trapezoid is adjusted, press the button to highlight ...to continue to ADJUST SIDE ANGLES, start with step 5 under...
  • Page 10 OSD Adjustments (Continued) M32 107T4 GS_3 Go to cover page 4) Press the button to highlight 9300K for GENERAL USE, 5) Press the button. The ROTATE IMAGE window appears. ROTATE 6500K for GAMES, or USER PRESET. should be highlighted. 5) Once you have highlighted GENERAL USE or GAMES, press the button to confirm you selection and return to the MAIN CONTROLS window.
  • Page 11 OSD Adjustments (Continued) M32 107T4 GS_3 Go to cover page 4) Press the button to select YES or NO. NO is the default. 4) Press the button. The ADJUST MOIRE window appears. YES returns all settings to their original factory adjustments.

  • Page 12: Troubleshooting

    M32 107T4 GS_3 OSD Adjustments (Continued), Troubleshooting Go to cover page DEGAUSS Monitor Specific Troubleshooting EXTRA CONTROLS is a set of three features, including DEGAUSS. Self-Test Feature Check (STFC) Degaussing removes electromagnetic build up that may distort the color Your monitor provides a self-test feature that allows you to check on your screen.

  • Page 13: Lock/Unlock, Factory Mode, Burn In

    Lock/Unlock, Factory Mode, Burn In, Service Mode M32 107T4 GS_3 Go to cover page Front Control To access factory mode 1. Turn off monitor (don't turn off PC) 2. Press " " and " " simultaneously on the front control panel,then press "...

  • Page 14: Warning And Notes

    Warning and Notes M32 107T4 GS_3 Go to cover page Warnings Notes 1. Safety regulations require that the unit should be returned 1. The direct voltages and waveforms are average voltages. in its original condition and that components identical to They have been measured using the Service test software the original components are used.

  • Page 15: Mechanical Instructions

    Mechanical Instructions M32 107T4 GS_3 Go to cover page 0. General To be able to perform measurements and repairs on the "circuit boards", these unit should placed in the service position first. 1.Remove the rear cover lids (screw cover) -Remove right and left lib (screw cover) on the back cover as shown in Fig.
  • Page 16 M32 107T4 GS_3 Mechanical Instructions Go to cover page 4. Main panel with Bottom Tray - Disconnect the degaussing coil (1113)from Main panel as shown in Fig. 6. - Remove the video panel from CRT neck. - Remove the "screw" of I/F cable from Main panel, grounding screw , wire as shown in Fig.
  • Page 17 Mechanical Instructions M32 107T4 GS_3 Go to cover page 5. How to remove Main Panel (Chassis) After remove "Main panel with bottom tray": Fig. 18 - Remove a screw from back of bottom tray as shown in Fig. 15. - Remove Interface cable from bottom tray as shown in Fig. 16.

  • Page 18: Wiring Diagram

    Wiring Diagram M32 107T4 GS_3 Go to cover page 1113...

  • Page 19: Hex Data Of Ddc2B

    Hex Data of DDC2B M32 107T4 GS_3 Go to cover page Standard Timing Identification #6 ********************************************************************** Horizontal active pixels : 800 M32 107T4 71K CPT Tube EDID log file Aspect Ratio : 4:3 ********************************************************************** Refresh Rate : 100 Vendor/Product Identification...
  • Page 20 Hex Data of DDC2B M32 107T4 GS_3 Go to cover page Standard Timing Identification #6 ********************************************************************** Horizontal active pixels : 800 M32 107T4 71K PHL Tube EDID log file Aspect Ratio : 4:3 ********************************************************************** Refresh Rate : 100 Vendor/Product Identification...
  • Page 21 Hex Data of DDC2B M32 107T4 GS_3 Go to cover page Standard Timing Identification #6 ********************************************************************** Horizontal active pixels : 800 M32 107T4 71K LG Tube EDID log file Aspect Ratio : 4:3 ********************************************************************** Refresh Rate : 100 Vendor/Product Identification...
  • Page 22 Hex Data of DDC2B M32 107T4 GS_3 Go to cover page Standard Timing Identification #6 ********************************************************************** Horizontal active pixels : 800 M32 107T4 71K SDI Tube EDID log file Aspect Ratio : 4:3 ********************************************************************** Refresh Rate : 100 Vendor/Product Identification...

  • Page 23: Ddc Instructions

    DDC Instructions M32 107T4 GS_3 Go to cover page 1. General 3. Pin assignment DDC Data Re-programming A. 15-pin D-Sub Connector In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect,repaired monitor’ the serial numbers have to be re-programmed.
  • Page 24 DDC Instructions (Continued) M32 107T4 GS_3 Go to cover page 4. Configuration and procedure 3. At the submenu, type the letter of your computer's floppy disk drive followed by :EDID301 (for example, A:\EDID301, as shown in Fig. 5). There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores all factory settings and DDC data (EDID code) which is so called Software DDC.
  • Page 25 DDC Instructions (Continued) M32 107T4 GS_3 Go to cover page Re-programming EEPROM (Software DDC) 4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 13. Step 1: After initialize alignment box, connecting all cables and box as shown in Fig.
  • Page 26 M32 107T4 GS_3 DDC Instructions (Continued) Go to cover page Step 5: **Configuration Setup & Enter Factory Mode ** Step 6: Write DDC data for "write EDID data" Click (Write EDID) icon from the tool bar to write DDC data.
  • Page 27 DDC Instructions (Continued) M32 107T4 GS_3 Go to cover page Step 9: Load DDC data Note 2 : In Factory Mode: Read/Write DDC data Before Read/Write EDID code, please confirm that the Click from the tool bar. Software DDC only was enabled as shown in Fig. 23.

  • Page 28: Electrical Adjustments

    Electrical Adjustments M32 107T4 GS_3 Go to cover page 5. To access factory mode 0. General 5.1 Turn off monitor (don't turn off PC) When carry-out the electrical settings in many cases a video signal 5.2 Press " " and "...
  • Page 29 ( for ref. 4,4) gain. LF (BRIGH SHARP) (for ref. 230) 48K SUB OSD R/G/B cut-off and R/G/B gain can be accessed (for Philips EXIT CRT), with initial data: Fig. 2.2 9300 K (for example: 152 is value of "BIAS R")
  • Page 30 Electrical Adjustments (Continued) M32 107T4 GS_3 Go to cover page 8. Focus adjustment Apply a signal of " @ " character. at 68.7 kHz/85 Hz mode set the brightness to mid-position , contrast to max - position and adjust the focus for optimal sharpness in the area within 2/3 from the screen center.

  • Page 31: Safety Test Requirements (Hipot & Ground)

    Safety test requirements M32 107T4 GS_3 Go to cover page All units that are returned for service or repair must pass the 3. Equipments and Connection original manufactures safety tests. Safety testing requires both Hipot and Ground Continuity testing. 3.1. Equipments...
  • Page 32 M32 107T4 GS_3 Function Block of M32 107T4 Go to cover page LIGHT VIDEO PRE- VIDEO & FRAME IC AMPLIFIER OUTPUT DEFLECTION UNIT STAGE TDA4823 STV9211 STV9556 OSD IC ROTATION NOVATEK LM358N FOCUS NT68275-00031 Self- test S-CAP H-OUTPUT/ VIDEO SWITCH...

  • Page 33: Video Panel (A) Schematic Diagram

    Video Panel Schematic diagram M32 107T4 GS_3 Go to cover page A1 7302-2 A4 1713-8 2 V/div AC 1 V/div AC 5 mS/div 5 mS/div 4.2V 1.6V A1 7302-4 A5 1713-7 4.2V 1.6V 4.2V 1.6V 62.3V 1 V/div AC 2 V/div AC 62.8V...
  • Page 35 54662SMC 54662cus(copper track) 54662HMC (SMD) (POSITION) 54662hmc(position) 2301 A4 1301 B1 3738 D3 3350 A2 2302 A5 1703 D2 3751 B4 3355 A3 54662smc(smd) 2304 A1 1711 C3 3752 B4 3361 A2 2305 A1 1712 C2 3753 E5 3362 A2 2306 A1 1713 C1 3754 D5...
  • Page 37 Deflection - Main Panel Schematic diagram M32 107T4 GS_3 Go to cover page B1 7503-C B22 7685-C B8 7501-6 7610-D B29 7801-18 50 V/div AC 5 V/div AC 50 V/div AC 100 V/div AC 0.5 V/div AC 5 mS/div 10 uS/div...

  • Page 39: Main Panel C.b.a.(B

    Main Panel C.B.A.(B,C) - copper track side view 3126 G5 2615 A3 3622 C4 3849 F7 9126 D4 6609 B1 3127 G5 2616 B4 3623 B4 3851 F7 9127 D4 GRID BOARD 6612 A4 3128 F5 2617 A4 3624 B5 3852 G7 9128 D4 # REF LABEL SIDE...
  • Page 40 Power Supply - Main Panel Schematic diagram M32 107T4 GS_3 Go to cover page 5113-1 83.6V 100 V/div AC 145.5V 5 uS/div 5113-4 1.7V 5 V/div AC 5 uS/div 5113-8 10 V/div AC 5 uS/div 5113-13 2.8V 12.6V 11.7V 2.5V 83.8V...
  • Page 41 Key Control Schematic diagram M32 107T4 GS_3 Go to cover page 1891 C2 1892 C2 1893 C3 1894 C3 1895 C4 3891 C2 KEY CONTROL BOARD 3892 C2 3893 C3 3894 C4 SB: 53022 x12 3895 C4 6891 D1 PB: 53032...

  • Page 42: Key Controlpanel C.b.a

    Key Control Panel C.B.A.(D) M32 107T4 GS_3 Go to cover page 1891 A2 1892 A2 1893 A2 1894 A3 1895 A4 3891 A2 3892 A3 3893 A2 3894 A3 3895 A3 6891 A1 8891 A4 53022cus 53022hmc...

  • Page 43: Repair Tips

    Repair Tips M32 107E4 GS_3 Go to cover page preferably be equipped with a thermal control (soldering 0. Warning temperature: 225 to 250 C). - The chip, once removed, must never be reused. All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD).

  • Page 44: Exploded View

    Exploded View M32 107T4 GS_3 Go to cover page...

  • Page 45: Recommended Parts List

    Recommended Parts List M32 107T4 GS_3 Go to cover page 1 313812752941 FRONT CABINET ASSY 2 313812752041 BACK COVER ASSY 3 313810798401 PEDESTAL ASSY 47 313810454231 BUTTON-POWER 49 313810454211 BUTTON-FUNCTION 601 313811704252 E-D.F.U ASSY 1052 313817863291 VIDEO PCB ASSY (107T4)

  • Page 46: Spare Parts List

    Spare Parts List M32 107T4 GS_3 Go to cover page 2511 203830150143 CAP PP PPN 1V S 5N6 PM5 A 2672 225264133527 CER2 DC Z5U 1KV S 5N6 PM20 B Parts List 2518 203801750216 ELCAP RE 16V S 22U PM20 R...
  • Page 47 Spare Parts List (Continued) M32 107T4 GS_3 Go to cover page 3625 212010593606 RST MOX 5W RSS S 1R PM5 B 3844 213810113103 RST CRB CFR-12 A 10K PM5 A 3504 212211000411 RST MFLM MF1/2WS A 110K PM1 A 3625...
  • Page 48 Spare Parts List (Continued) M32 107T4 GS_3 Go to cover page 3738 213810113181 RST CRB CFR-12 A 180R PM5 A 1052 Video PCB ASSY 1053 CONTROL PCB ASSY 3751 212211000332 RST MFLM MF1/2WS A 120R PM1 A 1052 313817863291 VIDEO PCB ASSY (107T4)

  • Page 49: Repair Flow Chart

    M32 107T4 GS_3 Repair Flow Chart Go to cover page A. Power Supply Failure 1. Sympton : check 7102 pin8 check 7102 check 7102 check 7102 no startup sound 100V<pin8<380V pin1 > 2V pin 5=2.4V pin6 output ? LED light off...
  • Page 50 Repair Flow Chart (Continued) M32 107T4 GS_3 Go to cover page rough check for R,G, B B.Video 1. video input= 0.7V check blanking Repair Flow 2. 7301video output =2.5V 7501 pin16 3. 7701 video output > 35Vpp check 1.Sympton :...
  • Page 51 M32 107T4 GS_3 Repair Flow Chart (Continued) Go to cover page C. Horizontal deflection output repair flow : 1. Sympton : check Hsync check Hsync check Hsync without 7606 base 7605 base 7501 pin8 H-deflection. check check Hsync check Hsync...
  • Page 52 Repair Flow Chart (Continued) M32 107T4 GS_3 Go to cover page basic check D. Vertical Deflection Failure +12/-12V Sympton : check check one horizontal line 3401,3403 6401 V_size is abnormal 3404 good? too large/small good check check 7401 7401 check 7501...
  • Page 53 Repair Flow Chart (Continued) M32 107T4 GS_3 Go to cover page check cpu pin6= 5V E. CPU Basic Check pin9/pin8=12MhZ check list pin7=gnd H size compensation for 71K S-CAPACITOR SWITCH TABLE 31. H-EHT the load variance Hor. Freq.(KHz) < 27.00 27.50-33.24...
  • Page 54 Repair Flow Chart (Continued) M32 107T4 GS_3 Go to cover page check 38. Rotation output from 0V to 5V check 3. ABL-CON output from 0V to 5V check key check 3836, 2822 23. Keypad Enter,Up,Down,Left,Right keys 3871~3875 check pin24 1.no H/V sync & IF cable pin5 floating - show msg.
  • Page 55 M32 107T4 GS_3 Repair Flow Chart (Continued) Go to cover page Basic check F. TDA4841 Vcc=pin9=pin10=12V Vcc > 9V Check List gnd =pin7=pin25=0v during startup 1. HFLB pin16 if no exist (from H.defl) CLBL=hi pin17 = Hunlock = floating pin30 = Hpll2 = 0V pin6 = HDRV = floating 2.
  • Page 56 Repair Flow Chart (Continued) M32 107T4 GS_3 Go to cover page Hunlock pin is floating while pll1(pin26) is 17. Hunlock unlock in searching mode 18. IIC scl = hi the initial sequence of IIC IC 19 IIC sda = hi...

  • Page 57: General Product Specification

    . FULL SCREEN SIZE APPLICATION . REAL MULTI-FREQ. - POWER SAVING MANAGEMENT SYSTEM - MAXIMIZED CONTAINER LOADING - VESA DDC2B - LOW EMISSION MPRII/TCO99/TCO95 (optional) 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 58 Focus check 4.10 Luminance uniformity 4.11 White color adjustment 4.12 Color tracking on full white pattern 4.13 Purity 4.14 Moire 4.15 Blemish 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 59 Grounding Certifications Safety Fulfil approbation requirements Reliability Mean time between failures 10.0 Quality assurance requirements 10.1 Acceptance test 11.0 Service ability 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 60 (between 0 and 0.6 V to be considered as low level, between 2.3 and 5.0 V as high level) C. Impedance Video : Terminated with 75 ohms Sync : Terminated with 4.7K ohms pull down resistors. 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 61 1024 x 768 60.0 KHz 75Hz (VESA) 1024 x 768 68.7 KHz 85Hz (VESA) 8. 1280 x 1024 64.0 KHz 60Hz (VESA) 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 62 The AUTOSCAN color monitor must be capable of displaying standard resolutions within the vertical(refresh) frequency range of 50 to 160 Hz and horizontal scan range of 30 71 KHz. 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 63 = 3.232 us Rear porch = 0.448 ms Sync width = 1.616 us Sync width = 0.064 ms Sync polarity = Sync polarity 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 64 = 2.201 us Rear porch = 0.524 ms Sync width 1.016 us Sync width = 0.044 ms Sync polarity = Sync polarity 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 65 = 4.064 us Rear porch 0.739 ms Sync width 1.270 us Sync width 0.079 ms Sync polarity = Sync polarity = 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 66 = 1.280 us Rear porch 0.478 ms Sync width = 2.400 us Sync width 0.125 ms Sync. polarity = Sync. polarity = 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 67 = 1.920 us Rear porch 0.513 ms Sync width 1.813 us Sync width 0.106 ms Sync. polarity = Sync. polarity = 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 68 = 2.889 us Rear porch 0.600 ms Sync width 1.037 us Sync width 0.050 ms Sync polarity = Sync polarity = 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 69 : 25.0 1 KV (Ib=0) Visible screen area : 325.1 mm x 243.8 mm CRT Source : CPT, PHL, LG, SDI 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 70 The display device is sufficiently protected against the burning of phosphors in case of repetitive power cycling or absence of horizontal deflection. 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 71 (preset modes only, refer to fig. 1) Width : 306 3 mm : 230 3 mm Height 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 72 (See Fig. 6). For 31.5kHz modes B Zone : 0.4mm. 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 73 : As stated in item 4.0, the purity must be checked under specific destinations of earth magnetic environments and the monitor must be well degaussed. 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 74 Canada Australia 5.2.2 Signal cable : 1.5 m ± 50 mm flying with 15 pin PS/2 Length of video D-shell socket 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 75 B-1 Container loading (integrated pedestal) Container size Q'ty W/ palette W/ palette Layers Sets per layer Sets per block Blocks per container Total sets 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 76 6.3.1 Ionizetic radiation Completely fulfill International Commission of Radio logical Protection (ICRP) requirement 0.5 mR/Hr. Actually the set can reach 0.1 mR/Hr. 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 77 TUV, GS Sweden SEMKO ---- Norway NEMKO ---- Denmark DEMKO ---- Finland FIMKO ---- U.S.A. UL, DHHS Canada Taiwan ---- BSM1 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 78 The service ability of this monitor should fulfil the requirements which are prescribed in UAW-0346 and must be checked with the check list UAT - 0361 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 79 GENERAL PRODUCT SPECIFICATION M32 107T4 Gs3 Go to cover page 303 mm 306 mm 309 mm FIG-1 IMAGE DIMENSION 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 80 M32 107T4 Gs3 GENERAL PRODUCT SPECIFICATION Go to cover page 306 mm |A-B| AND |C-D| < 5 mm FIG-2 IMAGE CENTERING 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 81 M32 107T4 Gs3 GENERAL PRODUCT SPECIFICATION Go to cover page 306 mm < 2 mm FIG-3 IMAGE ROTATION 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 82 M32 107T4 Gs3 GENERAL PRODUCT SPECIFICATION Go to cover page 306 mm A=B=C=D < 2.0 mm FIG-4 IMAGE GEOMETRY 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 83 M32 107T4 Gs3 Go to cover page 100 mm ZONE B ZONE A 306 mm FIG-5 CONTRAST AND BRIGHTNESS MEASUREMENT AREA 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 84 M32 107T4 Gs3 GENERAL PRODUCT SPECIFICATION Go to cover page ZONE B ZONE A ZONE C 306 mm FIG-6 MISCONVERGENCE 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 85 C < 1.20 mm D < 1.20 mm ( measured between flash on / off) Figure 7 Dynamic and Static EHT regulation distortion pattern 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 86 M32 107T4 Gs3 GENERAL PRODUCT SPECIFICATION Go to cover page Figure 8 Focus check character 17 M32 107T4-71K CMTR TYPE : 107T41/00C 8639 000 12287 2002-05-20 BRAND : PHILIPS Wayne Lin 2002-05-20 Forward Back...
  • Page 87 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page General Troubleshooting Guide No Display, Unstable Picture/ but LED is ON Picture Flickers or LED is amber (yellow) H/V Rolling, Monitor drivers H/V Sync. (inf file) Picture too bright Focus...
  • Page 88 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page NO DISPLAY, but LED is ON or LED is amber(yellow) Green Amber Amber? or Green? Make sure the correct signal is input. Is the ATTENTION Make sure of the state of the computer...
  • Page 89 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Picture is too bright or dark Press the OK button Bring up "MAIN CONTROLS" window Select "RESET TO FACTORY SETTINGS" Make sure of the signal cable connection. Make sure of the state of the computer (Turn on).
  • Page 90 Philips' monitors build in VESA DDC2B feature to support Plug & Play requirement for Windows 95/98/2000/Me . You can install the information file ( .inf) in order to select your Philips monitor from "Monitor" dialog box in Windows 95/98/2000/Me to activate Plug & Play application. The installation procedure...
  • Page 91 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Power management function is not active Verify the PC is compliant with VESA. In case all of the video signals of PC are not off, power management function is not active normally. [Repeat to power on and off (power management).]...
  • Page 92 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page A buzzing sound when powering on This sound is caused when the auto degaussing circuit is active. This buzzing sound is normal when the monitor is first turned on. This sound may be louder during the winter months and during initial power on.
  • Page 93 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page NO POWER / LED is off Is cabinet of monitor damaged being dropped? The monitor may have become 1. Is the correct AC power cord faulty due to excessive shock.
  • Page 94 M32 107T4 GS_3 General Troubleshooting Guide Go to cover page Color has irregularity Have you changed the Did you adjust the red, tilt or swivel angle green, and blue colors? of the monitor? Press OK " " button Select "EXTRA CONTROLS"...
  • Page 95 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Picture distortion is not adjusted normally. Is it possible to make adjustment by using the On Screen Display ? Press "OK" button, then bring up "MAIN CONTROLS" window. Adjust Horizontal, Vertical or Shape.
  • Page 96 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Picture is not stable 1. No picture is displayed for a few seconds in changing resolution (in changing display pixels ) such as picture disappearing in a moment, etc.. This is normal function to mask unstability in changing picture.
  • Page 97 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Need to change display size and adjust distortion Adjust each resolution according to user's guide.
  • Page 98 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Color Patterns visible on the screen Are Moire color fringes visible with some images? (e.g. Windows shutdown screen) Moire is the phenomenon interference fringes are visible on the screen. It oc curs due to the...
  • Page 99 : Moir is a natural effect or phenomenon of CRT that has the appearance of a wavy pattern é which is repetitive and superimposed on the screen as ripple images. , not just Philips monitor had. These are a few suggestions to help for reducing or minimizing the effect.
  • Page 100 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page OSD MAIN MENU LOCKED Press and hold the OSD menu key for about 10 seconds , until picture displays "OSD MAIN MENU UNLOCKED" Please contact your dealer/reseller for more information.
  • Page 101 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Shimmering/ Jitter/Video Noise Turn on monitor with a display or image for 30 minutes (due to drift). Jitter or Noise still present ? Try moving the monitor to another location to see if problem goes away.
  • Page 102 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Missing Color There are 2 easy ways to determine the Missing color problem. 1. View an image that is supposed to be "White". If one of the colors (RGB) is not functioning.
  • Page 103 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Color Purity Turn on monitor with a full image for 30 minutes (due to drift). Color Purity or Blotchy or Streaky Press Degauss button (or via the OSD manipulation) or Turn unit "OFF" then "ON" to degauss.
  • Page 104 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Power management function is not active Verify the PC is compliant with VESA. In case all of the video signals of PC are not off, power management function is not active normally. [Repeat to power on and off (power management).]...
  • Page 105 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page A buzzing sound when powering on This sound is caused when the auto degaussing circuit is active. This buzzing sound is normal when the monitor is first turned on. This sound may be louder during the winter months and during initial power on.
  • Page 106 M32 107T4 GS_3 Go to cover page CustoMax CustoMax is proprietary Philips software that allows user to control parameter (e.g. Size , Color , Geometry ) in place of the buttons on the front of the monitor. To install and run the CustoMax., you must have a USB compatible system and have a USB connection on the rear of your monitor.

  • Page 107: General Troubleshooting Guide

    WYSIWYG (what you see is what you get ) . The Colorific software is the property of Sonnetech ,Ltd. Only certain Philips monitor Models are equiped with the software. If you have special interesting , please hit the web site "http:\www.colorific.com".
  • Page 108 PC OEMs. USB 2.0 : Drafted by Compaq, Hewlett Packard, Intel, Lucent, Microsoft, NEC and Philips, USB Specification version 2.0 will increase device data throughout up to 480Mbps, 40 times faster than USB 1.1 devices.
  • Page 109 General Troubleshooting Guide M32 107T4 GS_3 Go to cover page Picture too Large or Small : Reset monitor via OSD menu maniputlation : Adjust the Horz(width) and.or Vert size (height) in the On Screen Display. : Change monitor timing to work at the recommended resolution.

  • Page 110: Lightframe For Windows

    Earlier Philips monitors or other manufacturers monitors will not work with this special software. It is recommended that you install this software only on a Philips monitor designed to use it. These monitors can be identified by the LightFrame logo on the front of the monitor.
  • Page 111 LightFrame for Windows (Continued) M30 107S2 GS_3 M32 107T4 GS_3 Go to cover page 5. Click Yes, Fig 9 bring up Fig.5 Fig 5 9. Click Finish, bring up LightFrame 3, Fig. 10 on the desktop. 6. Click Next, Fig 10 bring up Fig.6...
  • Page 112 LightFrame for Windows (Continued) M32 107T4 GS_3 Go to cover page 3b) If you want to highlight only an area of a window, click on the left mouse button and drag the cursor over the area to be highlighted while Operating LightFrame holding the mouse button.
  • Page 113 LightFrame for Windows (Continued) M32 107T4 GS_3 Go to cover page On button LightFrame 3 State and transition diagram Combined with Control bar appearance Add/remove button Off button Full screen button Help button LF Idle User clicks off or full screen...

This manual is also suitable for:

M32 107t4 gs 3

Table of Contents