Panasonic QUASAR PV-C1320 Service Manual page 7

Connections
Outdoor Antenna Connection
Unhook the antenna from your
previous TV or VCR and connect it to
(Flat) Twin Lead
the back of the unit as shown in the
300 Ohm Cable
diagram.
(Round) 75 Ohm
If your antenna system has separate coaxial Cable
UHF and VHF lead-ins, you need a
UHF/VHF Band Mixer (not supplied.)
from
WARNING:
Antenna
When using "Nut type" RF coaxial
cables, tighten with fingers only.
Overtightening may damage terminals.
(Flat) Twin Lead
300 Ohm Cable
DSS/Cable box Connections
Without a Cable Box
You can;
Antenna
record or view unscrambled channels.
You cannot;
CABLE
record or view scrambled channels.
view a channel other than the one
selected for any type of recording.
With a Cable Box
You can;
record or view any channel including scrambled channels.
NOTE: Channel selection must be made at the cable box.
You cannot;
view a channel other than the one selected for any
type of recording.
do a Timer recording of a channel unless you select it
at the cable box.
Note to CABLE System Installer
This reminder is provided to call the CABLE (Cable TV) System
Installers attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of
the building, as close to the point of cable entry as practical.
With a DSS Receiver
You can;
record or view any channel including scrambled
channels.
NOTE: Channel selection must be made at the DSS
Receiver.
You cannot;
view a channel other than the one selected for
any type of recording.
do a Timer recording of a channel unless you
select it at the DSS box.
NOTE:
The DSS receiver must be turned off to view
programs from a cable box or antenna. See the DSS
manual for details.
One Time Setup (continued)
Set TIME ZONE ADJUST.
Case 1
Display MAIN MENU.
1
Press ACTION.
2
Display SET CLOCK
M A I N MENU
screen.
VCR
T V LANGUAGE
1) Press
to select
C H C H CLOCK EX I T
+
CLOCK
SELECT : KEY
SET : ACT I ON KEY
2) Press ACTION
to display.
3 Select TIME
SET CLOCK
ZONE ADJUST.
AUTO CLOCK SET
1) Press
MANUAL
T I ME E ZONE ADJUST T : 0
to select.
SELECT : KEY +
2) Press
SET : KEY
END : ACT I ON KEY
subtract or add
hour(s) as
necessary.
4
End setup.
Press ACTION twice.
TIME ZONE ADJUST
returns to 0 if clock is set
manually.
Clock Setup is Incomplete
Case 2
Set the clock manually.
a
Display SET CLOCK
screen.
AUTO CLOCK SET
Press ACTION
I S I NCOMPLETE
to exit this
mode.
PUSH ACT I ON TO SET CLOCK
b Set the clock
SET CLOCK
:
1 / / 1 / / manually.
DST : ON
1) Press
SELE CT MONTH SE
select the month.
SELECT : KEY +
2) Press
SET : KEY
END : ACT I ON KEY
Likewise set date, year, time,
and DST (Daylight Saving Time.)
To Make Corrections,
repeatedly press
to error, then correct.
c
End setup.
Press ACTION twice
(Clock starts.)
PVQ-1310 / PV-C1320 / PV-C1330W / VV-1300 / VV-1310W / PV-C1340 / PV-C1350W / PV-C2010 / PV-C2020 / PV-C2030W / VV-2000 / PV-C2060
UHF/VHF Band
Mixer (not supplied)
VHF/UHF
or
300-75 ohm
Transformer
(not supplied)
Back of unit
<Model PV-C2060 unit is shown here>
unit
or
VHF/
UHF
Antenna
or
unit
CABLE
Cable Box
VHF/
IN OUT
UHF
Antenna
Satellite
or unit
CABLE
DSS Receiver
VHF/
IN IN
UHF
OUT
2
SET
SELECT
3
:CH UP
:CH DOWN
b
:VOL UP
:
VOL DOWN
+
1
ACTION
2
4
a
c
to
Notes
This unit's calendar is accurately maintained
up to Dec. 31, 2089, 11:59 PM.
Channel auto set selects normal TV or
Cable channels depending on your unit
hookup.
ACTION key on the unit
You can operate the
STOP/EJECT REW/
menu screen using unit
buttons.
ACTION
To display the menu,
press STOP/EJECT and
On Unit
REW together with no
tape inserted.
To exit the menu, repeat above with or
without tape inserted.
to
Using keys
to set.
: CH UP
: CH DOWN
+
: VOLUME UP
: VOLUME DOWN
On Remote
Whenever the menu or
to move
program screen is
displayed,
VOL CH
CHANNEL UP/DOWN
function as and
VOLUME UP/DOWN
On Unit
function as only.
One Time Setup
When the unit is turned on the first time, setup
mode is entered automatically.
1 Press POWER* on
the remote or unit.
Select the language.
2
SELECT LANGUAGE
PUSH CH : E n g l i s h for English
OPR I M I R CH : E s p a o l
for Spanish
APP. VOL + : F r a n a i s
for French
+
If wrong language is set, complete "Reset all unit Memory
Functions" steps.
If you use a cable box, it must be left on.
3 Start Channel Auto Set
CHANNEL / CLOCK AUTO SET
and Clock Auto Set.
CONNECT ANTENNA CABLE
Press CH
AND I F YOU USE A CABLE
BOX, TUNE I T TO YOUR
LOCAL PBS CH THEN. . .
PLE ASE PUSH CH UP KEY
CH AUTO SET PROCEED I NG
AUTO CLOCK SET
PROCEED I NG
Case 1 (Setup completed)
Press CH
6 / 7 / 2000 WED 12 : 00PM
DST : ON
daylight saving time,
SETT I NG : CH 1 0
but you would like to
AUTO CLOCK SET turn the DST feature
off, complete the
COMPLETED
"To Set or Reset the
END : PUSH CH UP KEY Clock" step and set DST
If your area observes daylight saving
time and DST is set to ON, but the
time is incorrect; complete the Time
Zone Adjust steps.
IMPORTANT NOTE FOR AUTO CLOCK SET
Auto clock set is performed the first time when the unit is turned off each day. If used, a cable box must be left on and
tuned to the PBS channel at the time the unit power is turned off if you want auto clock set to be done.
If using a DSS receiver, it must be turned off for auto clock set.
If a Cable Box or DSS receiver is connected to the unit via Audio/Video Jacks, an RF coaxial cable must also be
connected for auto clock set and channel auto set features.
If for any reason the time is changed manually, automatic time correction will not occur.
MTS Broadcast/TV Stereo System
Receivable Broadcast Types
The following are possible broadcast types with their accompanying
on-screen displays. The signal being received is indicated with an
mark while the selected audio mode is indicated with an arrow.
To change the audio mode for these broadcasts, follow the Select Audio
Mode for TV Viewing section (below.)
Display the broadcast signal
being received.
Press DISPLAY to display.
MTS Stereo and SAP broadcast
STOP 1 2 : 0 0AM ABC
0 : 0 0 : 0 0
Multi-channel Television Sound Stereo
SP
STEREO
SAP (main language) and Secondary Audio
MONO
Program (sub language) broadcasts are
both being received simultaneously.
Select the STEREO or SAP audio mode.
MTS Stereo broadcast
STOP 1 2 : 0 0AM ABC
0 : 0 0 : 0 0 Multi-channel Television Sound Stereo
STEREO SP
broadcast. Select STEREO audio mode.
SAP
MONO
If stereo broadcast is weak and the display
flickers, select MONO audio mode for
possibly better results.
SAP broadcast
STOP 1 2 : 0 0AM ABC
0 : 0 0 : 0 0 Secondary Audio Program (sub language.)
STEREO SP
Select SAP audio mode for the sub language.
SAP
MONO
MONO broadcast
STOP 1 2 : 0 0AM ABC
0 : 0 0 : 0 0
Normal monaural sound broadcast.
STEREO SP
SAP
MONO
Select Audio Mode for TV Viewing
Press AUDIO to select the desired
audio mode as described above.
(Arrow shows selection.)
Each press of AUDIO will change the audio
mode as shown below.
SAP is selected with first press of AUDIO.
< Example >
STOP 1 2 : 0 0AM ABC
Press 0 : 0 0 : 0 0
STEREO SP
AUDIO
SAP
MONO
STOP 1 2 : 0 0AM
STEREO
SAP
MONO
Press
AUDIO
Press
AUDIO
7
Process of Setup
Language channel Clock
1
POWER
2
(Español)
3
(Français)
+
2
2
CHANNEL
DOWN
.
Case 2 (Setup incomplete)
to exit.
AUTO CLOCK SET
I S I NCOMPLETE
PUSH ACT I ON TO SET CLOCK
: OFF.
+
ABC
0 : 0 0 : 0 0
SP
IMPORTANT NOTE:
STOP 1 2 : 0 0AM ABC
0 : 0 0 : 0 0
<For model PV-C2060 only>
STEREO SP
SAP
This stereo system is designed
MONO
for TV viewing only. Recording
and playback will always be in
monaural.
CHANNEL
UP
VOLUME
UP