Example Of Integrator Mode Operation - Pioneer PDP-425CMX Technical Manual

5.4.2 Example of Integrator Mode Operation

The basic operation in the menu mode is explained using
brightness adjustment as an example.
Remote control unit
DISPLAY
STANDBY/ON MENU
/ SET
MENU DISPLAY
/ SET
Main-control panel
1
Set the device to normal operation then press
the [INPUT] button to switch to the input to be
adjusted.
2
Press the [DISPLAY] button on the remote
control unit or the main-control panel to display
'DISPLAY CALL 1'.
F H : 3 1 . 5 k H z
F V : 6 0 . 0 H z
6 4 0
POL.H : N EGA
POL. V : POSI
3
Press the [DISPLAY] button on the remote
control unit or the main-control panel (3 seconds
or more) when 'DISPLAY CALL 1' is displayed to
display 'DISPLAY CALL 2'.
P D P - 4 2 5 C M X / LV C 5
S E R I A L N O.
L OT
DAT E
H O U R M E T E R
T E M P E R AT U R E
O S D
B AU D R AT E
FA N C O N T R O L
I D N O. S E T
C O L O R M O D E
I N F O R M AT I O N
: A B C D E F G H I J K L M N
DISPLAY
MENU
2/3
SET
5/∞
INPUT SCREEN SIZE – VOL +
5/∞ 2/3
I N P U T 1
4 8 0
X
FULL
: * * * * * * * * * * * * * * * *
: 0 0 1 A 0 0 1 K
: 0 0 1 A 0 0 1 X
: 0 0 2 3 9 H
: + 2 5
: O N
: 9 6 0 0 B P S
: AU TO
: A L L
: N O R M A L
4
Press the [MENU] button on the remote control
unit or the main-control panel when 'DISPLAY
CALL 2' is displayed to open up the integrator
mode screen.
I N T E G R AT O R
P I C T U R E S C R E E N
C O N T R A S T
B R I G H T N E S S
H . E N H A N C E
V . E N H A N C E
W H I T E B A L A N C E
C O L O R D E T A I L
G AMMA
P I C T U R E R E S E T
ENTER
SET
5
Press the [5/∞] buttons on the remote control
unit or the main-control panel to select
'BRIGHTNESS' then press the [SET] button.
I N T E G R AT O R
P I C T U R E S C R E E N
C O N T R A S T
B R I G H T N E S S
H . E N H A N C E
V . E N H A N C E
W H I T E B A L A N C E
C O L O R D E T A I L
G AMMA
P I C T U R E R E S E T
ENTER
SET
6
Press the [2/3] buttons on the remote control
unit or the main-control panel to adjust to the
desired picture.
B R I G H T N E S S
SET
SET
It is possible to move to other adjustment items
with the 5/∞ buttons.
7
Press the [SET] button on the remote control
unit or the main-control panel.
The adjusted value is saved in memory then
operation returns to the screen in step 5.
To continue with adjusting another item, repeat
steps 5 to 6.
8
When adjustment is complete, press the [MENU]
button on the remote control unit or the main-
control panel button to return to the normal
screen.
* The ID is shown to the side of the input display,
upper right area of the integrator mode screen
(See section 5.5.4, "ID Assigning" (pg. 195)).
Integrator Mode
I N P U T 1
S E T U P O P T I O N
: 1 2 8
: 1 2 8
: 0
: 0
: 2 . 0
EXIT
MENU
I N P U T 1
S E T U P O P T I O N
: 1 2 8
: 1 2 8
: 0
: 0
: 2 . 0
EXIT
MENU
:
0
EXIT
MENU
155