JVC UX UX-LP5 Instructions

Warnings, Cautions and Others
Mises en garde, précautions et indications
diverses
MICRO COMPONENT SYSTEM
UX-LP5
—Consists of CA-UXLP5 and SP-UXLP5
For turning off the demonstration display, see "Display
The lightning flash with arrowhead symbol,
Demonstration" on page 3.
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
ENGLISH "dangerous voltage" within the products
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
Thank you for purchasing a JVC product.
maintenance (servicing) instructions in the
literature accompanying the appliance.
INSTRUCTIONS
LVT1986-019A[J/C]
0109KMMMDWCDT
©2009 Victor Company of Japan, Limited
For customer use:
Le symbole de l'éclair à l'intérieur d'un triangle
Enter below the Model No. and Serial No. which are
équilatéral est destiné à alerter l'utilisateur sur
located either on the rear, bottom or side of the cabinet.
la présence d'une "tension dangereuse" non
Retain this information for future reference.
isolée dans le boîtier du produit. Cette tension
Model No.
est suffisante pour provoquer l'électrocution
Serial No.
de personnes.
Le point d'exclamation à l'intérieur d'un
For U.S.A.
triangle équilatéral est destiné à alerter
This equipment has been tested and found to comply with
l'utilisateur sur la présence d'opérations
the limits for a Class B digital device, pursuant to part 15 of
d'entretien importantes au sujet desquelles
the FCC Rules.
des renseignements se trouvent dans le
These limits are designed to provide reasonable protection
manuel d'instructions.
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
CAUTION:
energy and, if not installed and used in accordance with
Changes or modifications not approved by JVC could void
the instructions, may cause harmful interference to radio
the user's authority to operate the equipment.
communications. However, there is no guarantee that
WARNING: TO REDUCE THE RISK OF FIRE OR
interference will not occur in a particular installation. If this
ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
equipment does cause harmful interference to radio or
TO RAIN OR MOISTURE.
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
CAUTION
correct the interference by one or more of the following
To reduce the risk of electrical shocks, fire, etc.:
measures:
1. Do not remove screws, covers or cabinet.
Reorient or relocate the receiving antenna.
2. Do not expose this appliance to rain or moisture.
Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit ATTENTION
different from that to which the receiver is connected. Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
Consult the dealer or an experienced radio/TV technician 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
for help. coffret de l'appareil.
2. Ne pas exposer l'appareil à la pluie ni à l'humidité.
Getting Started
Supplied Accessories Connections
After unpacking, check to be sure that you have all the
following items.
To connect the To connect the FM antenna (supplied)
• Remote control, RM-SUXLP5J (× 1) monitor (not Extend it so that you can obtain the best reception.
• Lithium coin battery CR2025 (× 1) supplied)
– The battery has been installed in the remote control
Video cord
when shipped from the factory.
(not supplied)
• AM loop antenna (× 1)
• FM antenna (× 1)
• Protection sheet (× 1)
If anything is missing, consult your dealer immediately. For better FM reception
Prepare the Remote Control
When you use the remote control for the first time, pull out
Monitor
the insulation sheet.
Insulation sheet
Rear view
To Replace the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
To a wall outlet
For USA-California Only
Plug the AC power cord only after all connections are complete.
This product contains a CR Coin Cell Lithium Battery which
contains Perchlorate Material – special handling may
apply.
NOTES:
See www.dtsc.ca.gov/hazardouswaste/perchlorate
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
CAUTION:
• Make sure both the speakers are connected correctly and firmly.
Danger of explosion if battery is incorrectly replaced.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
Replace only with the same or equivalent type.
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
IMPORTANT FOR LASER PRODUCTS
CAUTION: Proper Ventilation
1. CLASS 1 LASER PRODUCT
To avoid risk of electric shock and fire, and to prevent
2. CAUTION: Do not open the top cover or cabinet. There
damage, locate the apparatus as follows:
are no user serviceable parts inside the unit; leave all
1. Front: No obstructions and open spacing.
servicing to qualified service personnel.
2. Sides/Top/Back: No obstructions should be placed in the
3. CAUTION: Visible and/or invisible class 1M laser radiation
areas shown by the dimensions below.
when open. Do not view directly with optical instruments.
3. Bottom: Place on the level surface. Maintain an adequate
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
air path for ventilation by placing on a stand with a
INSIDE THE UNIT.
height of 10 cm or more.
ATTENTION: Aération correcte
IMPORTANT POUR PRODUITS LASER
Pour prévenir tout risque de décharge électrique ou
1. PRODUIT LASER CLASSE 1
d'incendie et éviter toute détérioration, installez l'appareil
2. ATTENTION: N'ouvrez pas le couvercle supérieur ni
le coffret de l'appareil. Il n'y a aucune pièce réparable de la manière suivante:
par l'utilisateur à l'intérieur de l'appareil; confiez toute 1. Avant: Bien dégagé de tout objet.
2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque
réparation à un personnel qualifié.
les espaces indiqués sur le schéma ci-dessous.
3. ATTENTION: Rayonnement laser visible et/ou invisible
3. Dessous: Posez l'appareil sur une surface plane et
de classe 1M une fois ouvert. Ne pas regarder directement
horizontale. Veillez à ce que sa ventilation correcte puisse
dans le faisceau avec des instruments optiques.
se faire en le plaçant sur un support d'au moins dix
4. REPRODUCTION DE L'ÉTIQUETTE: ÉTIQUETTE DE
centimètres de hauter.
PRÉCAUTION PLACÉE À L'INTERIEUR DE L'APPAREIL.
Front view/Face
CAUTION
The button in any position does not disconnect the mains
line.
CAUTION:
Disconnect the mains plug to shut the power off completely
• Do not block the ventilation openings or holes. (If the
(the STANDBY lamp goes off).
ventilation openings or holes are blocked by a newspaper or
The MAINS plug or an appliance coupler is used as the cloth, etc., the heat may not be able to get out.)
disconnect device, the disconnect device shall remain readily • Do not place any naked flame sources, such as lighted
operable. candles, on the apparatus.
• When the system is on standby, the STANDBY lamp lights • When discarding batteries, environmental problems
red. must be considered and local rules or laws governing the
• When the system is turned on, the STANDBY lamp goes off. disposal of these batteries must be followed strictly.
The power can be remote controlled. • Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
ATTENTION
vases, shall be placed on the apparatus.
La touche , quelle que soit sa position, ne coupe pas la
ligne principale.
Débrancher la fiche principale pour couper complètement ATTENTION:
l'alimentation du secteur (le témoin STANDBY s'éteint). • Ne bloquez pas les orifices ou les trous de ventilation. (Si
La fiche secteur ou un coupleur est utilisé comme dispositif les orifices ou les trous de ventilation sont bloqués par un
de déconnexion de l'appareil, et l'appareil déconnecté doit journal un tissu, etc., la chaleur peut ne pas être évacuée
être prêt à être utilisé. correctement de l'appareil.)
• Ne placez aucune source de flamme nue, telle qu'une
• Quand l'appareil est en mode d'attente, le témoin STANDBY
bougie, sur l'appareil.
est allumé en rouge.
• Lors de la mise au rebut des piles, veuillez prendre en
• Quand l'appareil est sous tension, le témoin STANDBY
considération les problèmes de l'environnement et suivre
s'éteint.
strictement les règles et les lois locales sur la mise au
L'alimentation peut être commandée à distance.
rebut des piles.
CAUTION: Excessive sound pressure from earphones or • N'exposez pas cet appareil à la pluie, à l'humidité, à un
headphones can cause hearing loss. éqgouttement ou à des éclaboussures et ne placez pas
ATTENTION: Une pression acoustique excessive des écouteurs des objets remplis de liquide, tels qu'un vase, sur l'appareil.
ou du casque d'écoute peut entraîner une perte auditive.
CAUTION: Battery shall not be exposed to excessive heat
such as sunshine, fire, or the like.
ATTENTION: Les piles ne doivent en aucun cas être
exposées à une chaleur excessive (lumière du solei, feu, etc.).
1
Do not connect the AC power cord until all other connections have been made.
To connect the AM loop antenna
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
FM antenna (supplied) NOTE: Keep the AM loop
antenna cable wrapped around
the AM loop antenna frame,
Outdoor FM antenna
otherwise the effectiveness
(not supplied)
and sensitivity of the AM loop
antenna may be reduced.
Disconnect the supplied FM antenna,
and connect to an outdoor FM
antenna using a 75 Ω wire with coaxial
type connector.
To connect the speaker cords
From right
speaker
2
Basic and Common Operations
STANDBY lamp
Side view/Côté
Display Demonstration
When you plug in the System, the display demonstration automatically starts.
To cancel the display demonstration, press and hold DEMO until "DEMO CLR" is
displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does not work (and
you cannot deactivate it).
• When the display demonstration is activated, it also starts if no operation is done
for about 2 minutes while the System is turned on.
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and headphones
when you turn on the System or start playback.
[European Union only]
[Union européenne seulement] The operations on pages 4 to 6 are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button names,
they can also be used for the operations.
Playing Back a Disc
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
To assemble the AM loop antenna
in ISO 9660 format.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
Loading a Disc
(on the System only)
1 Press to open the disc tray.
2 • When using an 8 cm (3 3/16 inch) disc, place it
on the inner circle of the disc tray.
Black
White
3 Press to close the disc tray.
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc while the
System is on standby.
Press these buttons for 2 seconds while the System is on
+
standby.
To cancel the prohibition, repeat the same procedure.
Press and hold
Release
Insert
Red
From left
Black
speaker
To
Point at the remote sensor on the front panel.
Turn on or off
(standby) the power
Select a source
Adjust the volume
Drop the volume in
a moment
Emphasize the
sound (Sound
Turbo)
Reinforce the bass
sound (Hyper Bass
Sound)
Adjust the tone
(Bass/Treble)
PHONES jack
Stereo mini plug cord
Dim the display
Set the clock and
timer
Change the display
information
Set the ECO
(Ecology) Mode
3
Basic Disc Operations
To Press Indication/Result
Play back the disc • Current track number and elapsed playing
time appear.
CD
• During playback, press again to pause.
Stop playback • While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select a track Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group Select the next groups.
UP
(MP3/WMA only)
Select the previous groups.
DOWN
Forward search/ Press and hold to fast-forward the track during
Reverse search playback.
To stop searching, release the button.
Press to fast-forward the track during playback.
To stop searching, press 6.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
Press to fast-reverse the track during playback.
To stop searching, press 6.
Change display Press repeatedly.
DISPLAY
information
NOTES:
• If no disc is inserted, "NO DISC" appears on the main display.
• If MP3/WMA files are not recorded on the disc, "NO PLAY" appears on the main
display.
RESUME Play
Press RESUME to activate RESUME Play so that the RESUME indicator lights up.
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the beginning of the
stopped track.
To clear the memory, open the disc tray.
• When you clear the memory and start playback, playback starts from the first
track
To deactivate RESUME Play, press RESUME again.
NOTE:
This function does not work in Program Play.
4
Press
Indication/Result
System Remote
The STANDBY lamp on the System turns off/on.
See "Playing Back a Disc on page 4 and "Listening to an iPod/Viewing
CD
Images on the iPod" on page 5.
iPod
For the remote control • For "FM/AM," see "Listening to FM
AUDIO IN
and AM Broadcasts" on page 5.
TUNER
TUNER FM TUNER AM
AUDIO IN
• For "AUDIO IN," see "Listening to
AUDIO IN
Other Equipment" on page 5.
TUNER
Adjustable range: Level 0 ("VOL MIN") to level 40 ("VOL MAX").
VOLUME
To restore the volume, press again, or adjust the volume level.
FADE
MUTING
—
The S.TURBO indicator lights up.
SOUND TURBO
— To cancel this function, press again.
The BASS indicator lights up.
HBS
— To cancel this function, press again.
Press once for adjusting the bass level; twice for treble level, then, press
BASS/TREBLE
VOLUME +/–.
Adjustable range: –3 to +3.
—
VOLUME
You can dim the display window and illumination lamp.
While the System is turned on...
DIMMER
For setting the clock, see "Setting the Clock and Using Timers" on page 6.
CLOCK/
TIMER
—
The display information changes as follows:
FM: Clock = Frequency
AM: Clock = Frequency
—
DISPLAY
CD: Current track elapsed time = CD total remaining time = Current track
remaining time
MP3/WMA: Current track elapsed time = ID3 tag = Current group/track
Press when the System is on standby.
Setting the ECO (Ecology) Mode allows you to reduce power consumption
—
by turning the display (clock display) off while on standby.
To cancel this function, press again when the System is on standby.
Playing Repeatedly—Repeat Play
1 Press repeatedly to specify the repeat mode as follows:
REPEAT
: Repeats the current (or specified) track.
: Repeats all tracks in the current group
(MP3/WMA only).
ALL: Repeats all tracks.
No indicator (Off): Normal playback
2
CD
Programming the Playing Order—Program Play
1 During stops, press so that the PRGM (program) indicator
PROGRAM
lights up.
2 Select a track number.
or
3 Press to program the selected track.
SET
4 Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 32nd track, "PRG FULL" will appear.
5 The tracks are played back in the programmed order.
CD
Operations for Program Play (while program stop mode)
• To check the programmed contents, press SET repeatedly.
• To add tracks, after "- - -" appears on the display by pressing SET repeatedly,
repeat steps 2 and 3 above.
• To erase or exit the program, press 7.
– The stored program is not kept.
Playing at Random—Random Play
1 Press so that the RND (random) indicator lights up and playback
RANDOM
starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press RANDOM so that the RND (random) indicator
disappears during playback.