JVC DLA-M2000LU Operating Instructions Manual page 25

Menu Operations
Menu Transition Diagram in PC Menu Mode
Main menu in Video Menu Mode
5 ∞
5 ∞
2 3
Menu
Image adj.
3
Brightness
Image adj.
Setting Contrast
Sharpness
Color temp.
Brightness
All reset
Options
Contrast
Language
Sharpness
Information
All reset
5
5 ∞
5 ∞
2 3
Menu
Setting
Image adj.
Tracking
3
Setting Tracking
Phase
Color temp. Phase
Position
Options
Position
Resize
Language
Resize
Clamp
Information
Clamp
5 ∞
5 ∞
2 3
Menu
Color temp.
Image adj.
3
R-Gain Color temp.
Setting
Color temp. G-Gain R-Gain
Options B-Gain G-Gain
Language
All reset B-Gain
Information
All reset
∞
5
5 ∞
2 3
Menu
3 Options 1
Image adj. Menu display
Line display
Menu display
Setting
Keystone
PC2 (BNC)
Color temp. Line display
Right Left rev.
Options
Keystone
Top Bottom inv.
RS-232C
Language
PC2 (BNC)
Sleep time
Information
Options 2
∞ 5 ∞
∞ 5
Menu Language
Image adj.
Setting
English
Color temp.
Deutsch
Options EspaÒol
Language Italiano
Information FranÁais
5 ∞
Note
Menu
• The display languages of the menus are set to "English" when the projector
Image adj.
Input PC 1
is bought. The display language can be selected from the following 6
Setting
Switcher CH.0
Color temp.
Resolution 1280 1024 languages: "
Frequency H 79.9 kHz
Options
"Espanol (Spanish)", "Italiano (Italian)" and "Francais (French)". (Refer to
Frequency V 75 Hz
Language
page 45.)
Lamp time
123 h
Information
The language settings in the section are explained in "English".
40
Submenus in Video Menu Mode
2 3
Image adj.
All reset?
12
Yes No
12
1 2 3 4 5
ENTER
5 ∞ 2 3
Position
123
Disp.Posi. Menu
12
ENTER 12,12 ENTER
1:1 Panel Aspect
ST FP BP
2 3
Color temp.
Low Middle High
All reset?
123
Yes No
123
123
ENTER
Keystone 0
15sec ON
5sec OFF
ENTER
RGB YP P
B R
ENTER
Options 2
English Right Left rev. OFF ON
Deutsch Top Bottom inv. OFF ON
EspaÒol
RS-232C [bps] 9600 19200
Italiano
15 30 60 OFF
Sleep time [min]
FranÁais
Options 1
ENTER
5 ∞
2 3
(Japanese)", "English (English)", "Deutsch (German)",
Quick Reference Guide for PC Menu Mode
Main Menu in PC Menu Mode (While receiving computer-related signals)
Image adj. (Refer to page 47)
Brightness: Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
Contrast: Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
Sharpness: Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
All reset: Resets above items to the factory set values.
Yes / No
Setting
Tracking: The lateral size and display area of picture image can be adjusted. (–128 to +127)
(Refer to page 46)
Phase: Flickering or dim picture image can be adjusted. (0 to 31)
Position: Video screen position and menu position can be adjusted.
Disp. Posi. / Menu
Resize: The relationship between the number of pixels (resolution) and the screen can be selected.
(Refer to page 51)
"1:1": Picture image is projected with its original size.
Panel: Picture image is enlarged to the full size.
Aspect*: Picture image is enlarged while maintaining the original aspect ratio.
Clamp Selectable clamp position. Normally, set to "BP". ST / FP / BP*
Color temp.
Color temp. Adjustable color temperature, Low/Middle* /High.
Will be adjusted to correct reddish or blueish image.
R-Gain Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
G-Gain Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
B-Gain Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
All-reset Reset above items to the factory set values.
Yes/No
Options (Refer to page 52)
Options 1
Menu display: 15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
Line display: 5sec* (Line display such as "PC1" or "PC2" appears on top right of the screen for 5 seconds
when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
Keystone: Press ENTER to enter the Keystone submenu.
Keystone: Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
PC2 (BNC): RGB* or YP P . Set to RGB when a computer device with analog RGB, V, H/Cs signals is
B R
connected to the PC2 terminals. Set to YP
Y, R-Y) or DTV-format signals (Y, P
Options 2: Press ENTER to enter the "Option 2" submenu.
Right Left rev.: OFF* / ON (Select for upside-down hanging on the ceiling.)
Top Bottom inv.: OFF* / ON (Select for upside-down hanging on the ceiling.)
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min:] Selectable sleep times. If no-signal condition continues for the period
of selected time (Unite: Minutes), the projector enters the stand-by
mode. 15 / 30 / 60 / OFF*
Options 1: Press ENTER to return to the "Option 1" submenu.
Language Language for on-screen display.
Japanese / English* / German / Spanish / Italian / French
Information (Refer to page 52)
Input: Shows the terminal name selected by the PC button. (PC1or PC2)
Switcher: This display currently has no meaning. ("CH.0" is usually displayed to indicate that it is not being used.)
Resolution: Shows the resolution of the input signal being received. (Horizontal
It may not be displayed correctly with some input signals.
Frequency H: Shows the horizontal frequency of the input signal being received. (
Frequency V: Shows the vertical frequency of the input signal being received. (
Lamp time: Accumulated used hours of the light-source lamp.
* : Factory set value.
Menu Operations
(Refer to page 46)
(Refer to page 49)
P when a device with component signals (Y, B-
B R
, P ) are connected to the PC2 terminals.
B R
(Refer to page 45)
Vertical)
kHz)
Hz)
41