Kenwood KDC-MP5028 Service Manual page 13

ter this, any of the item can be selected)
* Normally, Sub Woofer Level is not included. In this ver-
sion, however, the Sub Woofer Level is included, and this
has been already arranged.
• With the remote controller, continuous forwarding is prohib-
ited.
• Using the VOL knob, the Fader is to be adjusted to the fol-
lowing three levels : R15 ↔ 0 ↔ F15. (The default value : 0)
• Using the VOL knob, the Balance is to be adjusted to the
following three levels : L15 ↔ 0 ↔ R15. (The default value :
0)
• Using the VOL knob, the Sub Woofer Level is to be adjusted
to the following three levels : -15 ↔ 0 ↔ +15 . (The default
value : 0)
• Using the VOL knob, Bass / Middle / Treble Level is to be
adjusted to the following three levels : -8 ↔ 0 ↔ +8 . (The
default value : 0)
• Using the VOL knob, the HPF Front / Rear is to be adjusted
to the following two levels : Through ↔ 180Hz (or 220Hz).
(The default value : Through)
• Using the VOL knob, the LPF Sub Woofer is to be adjusted
to the following two levels : 60Hz (or 50Hz) ↔ Through. (The
default value : Through)
• Using the VOL knob, the Sub Woofer Phase is to be ad-
justed to the following two levels : Reverse ↔ Normal . (The
default value : Normal)
• Using the VOL knob, the Volume Offset is to be adjusted to
the following two levels : -8 ↔ 0. (The default value : 0)
• Using the VOL knob, the Loudness ON / OFF is to be ad-
justed to the following two levels : OFF ↔ ON. (The default
value : OFF)
• Using the VOL knob, the 2 Zone ON / OFF is to be adjusted
to the following two levels : OFF ↔ ON. (The default value :
OFF)
• Items of Bass f / Bass Q / Bass EXT / Middle f / Middle Q /
Treble f are not included in the audio adjustment.
MENU Items
• By short-pressing [Q] key, MENU can be entered.
• The [DNPP/SBF] and [DIRECT] keys on the remote con-
troller can also be used to enter the MENU.
• With the remote controller, continuous forwarding is prohib-
ited.
• When a CD is used as a source, the default item will be the
F/W Version. (DXM-6800 mechanism installed models.)
TEST MODE
* DXM-6800 : X92-5100-00
KDC-MP5028/MP528
2-ZONE Items
• When using sources other than the STANDBY source, us-
ing a short-press on [AUTO] / [TI] key, 2-ZONE ON / OFF is
achieved.
(Since built-in AUX function is not available with KDC-X589
/ KDC-X7529, this is effective only when CA-C1AX is con-
nected.)
Backup Current Measurement
When reset in Acc OFF (Back Up ON) condition, MUTE termi-
nal goes off after 2 seconds, instead of 15 seconds. (During
this time, the CD mechanism does not function.)
OPEL Communication Items
During the test mode, OPEL communication line outputs the
following.
(At every 500msec, the output condition of the communica-
tion line will be switched.)
CE
DATA
CLK
500msec
500msec
500msec
Special display when all lights are on
When all lights are on with the STANDBY source, the follow-
ing displays are made when the keys shown below are pressed.
[1] Key Version display
(Display) 413K-1.02 ["Development Name" -
[2] Key Serial number display (8 digits)
(Display) xxxxxxxx
[3] Key Short-press : Power ON hours is displayed.
During Power On hours display, by long-pressing
for 2 seconds, the Power ON hours is cleared.
(Display) PON xxxxx
[4] Key Short-press : CD operation hours is displayed.
During CD operation hours display,
by long-pressing for 2 seconds, CD operation
hours is cleared.
(Display) CDT xxxxx
/W6031/W6031Y
"Version"]
MAX 65535 (Hours)
MAX 65535 (Hours)
13