Table of Contents
Advertisement
TIMER RECORDING ON HDD/DVD DECK
48
EN
Manual Timer Programming
You can program this unit to timer record as many as 16 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer record the program.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/DBS/DVD switch to DVD.
ENTER
1
Load a recordable disc if recording to DVD.
2
Press PROG to access the program top screen.
3
Press FGD E to select ACALENDAR PR.B, then press ENTER.
When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMSB appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
4
Press FGD E to select the desired date, then press ENTER.
5
Press F G to select ARECORD
TOB, then press ENTER. Press
F G to select the desired
recording deck, then press
ENTER.
6
Press F G to select ASTARTB,
then press ENTER. Press F G
to set the desired start time,
then press ENTER.
Each press of F G increases/decreases the start time in 1-
minute interval.
To increase/decrease the start time in 30-minutes interval,
press and hold F G.
7
Press F G to select ASTOPB, then press ENTER. Press F G to
set the desired stop time, then press ENTER.
Each press of F G increases/decreases the stop time in 1-
minute interval.
To increase/decrease the stop time in 30-minutes interval,
press and hold F G.
CABLE/DBS
TV
DVD
PROG
FGDE
2
PROGRAM > CALENDAR PR. (2/3)
01/08/03 WED 10:30PM - 11:00PM
DBS 100
[MISC. ] XP
SELECT WITH @
RECORD TO
HDD
THEN PRESS [ENTER]
10:30PM
START
PRESS [PROG] TO EXIT
11:00PM
STOP
CATV
SOURCE
100
CH
ENTER
PROG
CONFIRM
EXIT
SELECT
8
Press F G to select ASOURCEB, then press ENTER. Press F G
to select the desired source.
9
Press F G to select ACHB, then press ENTER. Press F G to
select the desired channel.
10
Press F G to select ACONFIRMB, then press ENTER.
11
Set the other recording options as required.
Refer to step 8 in AVCR Plus+ Timer ProgrammingB
(A pg. 46).
12
Press F G to select AOKB,
then press ENTER to access
the Program Confirmation
screen.
13
Press D E to select AEXITB,
then press ENTER to
complete timer
programming.
To program another timer,
press D E to select ACONTINUEB, then press ENTER.
If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
NOTES:
When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
If the copy limited program is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
Cable box and DBS Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform AManual Timer ProgrammingB (A pg. 48).
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver's power on.
Relief Recording
When a program that is set for the DVD deck cannot be
recorded properly, the program is recorded to the HDD deck
instead in XP mode.
If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
2
PROGRAM > CALENDAR PR. (3/3)
01/08/03 WED 10:30PM - 11:00PM
DBS 100
GARDENING
[EDUCATION] FR360
1:00
28:00
SELECT WITH @
INPUT NAME
GARDENING
THEN PRESS [ENTER]
CATEGORY
EDUCATION
PRESS [PROG] TO EXIT
WEEKLY/DAILY
MON-FRI (FOR A WEEK)
REC MODE
FR360
PROG
ENTER
OK
EXIT
SELECT
Advertisement
Table of Contents
