Sony MKS-7171X Operation Manual page 15

d NETWORK A (CTRL) connector (RJ-45
compliant)
1)
Connect to an Ethernet switch.
The MVS-8000X/MVS-7000X system's center control
panel is connected in the same way to the Ethernet switch
to form a network for exchange of signals between the
devices. This network is used primarily to control the
various devices from the center control panel of the MVS-
8000X/MVS-7000X system.
e NETWORK B (DATA) connector (RJ-45
compliant)
1)
Connect to an Ethernet
switch.
The MVS-8000X system's center control panel is
connected in the same way to the Ethernet switch to form
a network for exchange of signals between the devices.
This network is used primarily for exchange of various
types of data (key frame effects, snapshots, etc.) and still
pictures of frame memory.
CAUTION
• When you connect the FM DATA connector,
NETWORK A (CTRL) connector, NETWORK B
(DATA) connector and NETWORK C connector (MVS-
8000X system only) of the unit to peripheral devices, use
a shielded-type cable to prevent malfunction due to
radiation noise.
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following port(s).
- FM DATA (frame memory data) connector
- NETWORK A (CTRL) connector
- NETWORK B (DATA) connector
- NETWORK C connector (MVS-8000X only)
Follow the instructions for the above port(s).
1) For information about Ethernet switches that can be used in the MVS-
8000X/7000X system, contact your Sony service representative.
ATTENTION
Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une tension
excessive aux ports suivants.
- FM DATA connecteur
- NETWORK A (CTRL) connecteur
- NETWORK B (DATA) connecteur
- NETWORK C connecteur (MVS-8000X seulement)
Suivez les instructions pour les ports ci-dessus.
VORSICHT
Aus Sicherheitsgründen nicht mit einem Peripheriegerät-
Anschluss verbinden, der zu starke Spannung für diese
Buchse haben könnte.
- Buchse FM DATA
- Buchse NETWORK A (CTRL)
- Buchse NETWORK B (DATA)
- Buchse NETWORK C (nur MVS-8000X)
Folgen Sie den Anweisungen für die oben aufgeführten
Buchsen.
For more information about Ethernet switch connectors,
see "MVS-8000X/MVS-7000X System Configuration"
(page 16).
For more information about setting up the Ethernet switch,
refer to the documentation supplied with the switch.
f NETWORK C connector (RJ-45 compliant)
This connector is reserved for future system expansion.
g U (signal ground) terminal
Connect to the system ground.
h - AC IN (AC power input) A, B, C, and D
connectors (3-pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cords.
Note
When the HK-PSU05 Power Supply Unit is not installed
in the front-side slot inside the switcher processor, it is not
possible to use the - AC IN connector on the rear panel
of the processor.
For more information about installing an HK-PSU05
Power Supply Unit, contact your Sony service
representative.
i GPI (General Purpose Interface) 1 and 2
connectors (D-sub 25-pin)
Connect to external devices for input and output of trigger
signals. Up to eight inputs and eight outputs are possible,
with input and output conditions set on the center control
panel (Future support for GPI 2 connector).
j REMOTE 1 to 4 connectors (D-sub 9-pin, RS-422A
compliant)
These connectors are used to control the auxiliary bus of
the MVS-8000X/MVS-7000X series from external
devices, or to operate the MVS-8000X/MVS-7000X from
editing control systems such as the BVE-9100.
Define the types of the connected devices on the center
control panel.
Location and Function of Parts
15