Table of Contents

Advertisement

SERVICE MANUAL
System
Laser: Semiconductor laser
Channel coverage:
PAL/SECAM (B/G, D/K, I, L)
VHF: E2 to E12, R1 to R12, F2 to F10,
Italian A to H, Ireland A to J, South
Africa 4 to 13
UHF: E21 to E69, R21 to R69, B21 to
B69, F21 to F69
CATV: S01 to S05, S1 to S20, France
B to Q
HYPER: S21 to S41
The above channel coverage merely ensures
the channel reception within these ranges. It
does not guarantee the ability to receive
signals in all circumstances.
Video reception: Frequency synthesizer
system
Audio reception: Split carrier system
Aerial out: 75-ohm asymmetrical aerial
socket
Timer: Clock: Quartz locked/Timer
indication: 24-hour cycle (digital)/
Power back-up duration: 1 hour
Video recording format: MPEG-2,
MPEG-1
Audio recording format/applicable
bit rate: Dolby Digital 2 ch
256 kbps/128 kbps (in EP and SLP
mode)
RDR-HX820/HX825
Photo: RDR-HX820
RMT-D230P
SPECIFICATIONS
Inputs and outputs
LINE 2 OUT
(AUDIO): Phono jack/2 Vrms/10 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y: 1.0 Vp-p,
C: 0.3 Vp-p (PAL)
LINE 2 IN
(AUDIO): Phono jack/2 Vrms/more than
22 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y: 1.0 Vp-p,
C: 0.3 Vp-p (PAL)
LINE 1 – TV: 21-pin
CVBS IN/OUT
S-Video/RGB OUT (upstream)
LINE 3/DECODER: 21-pin
CVBS IN/OUT
S-Video/RGB IN
S-Video OUT (downstream)
Decoder
DV IN: 4-pin/i.LINK S100
DIGITAL OUT (OPTICAL):
Op
tical output jack/–18 dBm
(wave length: 660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, P
/C
, P
B
B
Phono jack/Y: 1.0 Vp-p,
P
/C
: 0.7 Vp-p, P
B
B
G-LINK: mini jack
(for RDR-HX825 models only)
HDMI OUT: HDMI 19pin-Standard
Connector
for RDR-HX825
General
Power requirements: 220-240 V AC,
Power consumption: 46 W
Dimensions (approx.):
Hard disk drive capacity: 160 GB
Mass (approx.): 4.7 kg
Operating temperature: 5ºC to 35ºC
Operating humidity: 25% to 80%
Supplied accessories:
Specifications and design are subject to
change without notice.
Compatible colour systems
This recorder is designed to record using the
PAL colour system and play back using the
PAL or NTSC colour systems.
The signals of the SECAM colour system can
/C
):
be received or recorded but played back in the
R
R
PAL colour system only. Recording of video
sources based on other colour systems cannot
/C
: 0.7 Vp-p
R
R
be guaranteed.
RMT-D230P/D231P
AEP Model
RDR-HX820/HX825
50/60 Hz
430 × 73 × 328 mm (width/height/
depth) incl. projecting parts
Mains lead (1)
Aerial cable (1)
Remote commander (remote) (1)
Set top box controller (1)
(for RDR-HX825 models only)
R6 (size AA) batteries (2)

DVD RECORDER

Advertisement

Table of Contents
loading

Summary of Contents for Sony RDR-HX825

  • Page 1: Dvd Recorder

    LINE 3/DECODER: 21-pin Remote commander (remote) (1) signals in all circumstances. CVBS IN/OUT Set top box controller (1) (for RDR-HX825 models only) S-Video/RGB IN R6 (size AA) batteries (2) S-Video OUT (downstream) Video reception: Frequency synthesizer Decoder...
  • Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS SERVICE NOTE Easy Setup (Resetting the Recorder) ··································· 1-27 Additional Information ···························································· 1-28 DISK REMOVAL PROCEDURE IF THE TRAY Troubleshooting ··································································· 1-28 CANNOT BE EJECTED (FORCED EJECTION) ············ 5 Self-diagnosis Function BOARDS CONNECTION ················································· 6 (When letters/numbers appear in the display) ····················· 1-30 Notes About This Recorder ·················································...
  • Page 4 • RD-064 (5/8) (AV-CN/POWER) SCHEMATIC DIAGRAM ···························· 4-33 • RD-064 (6/8) (DV-PHY) SCHEMATIC DIAGRAM ···························· 4-35 • RD-064 (7/8) (PLL/AUDIO-AD-DA) SCHEMATIC DIAGRAM ···························· 4-37 • RD-064 (8/8) (HDMI) SCHEMATIC DIAGRAM ···························· 4-39 • SWITCHING REGULATOR (SRV-2001EK) SCHEMATIC DIAGRAM ···························· 4-41 4-3.
  • Page 5: Service Note

    SERVICE NOTE 1. DISK REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION) Remove the upper case. Insert the stiff wire in the hole and eject the tray. Hole The stiff wire Open the tray. Fig. 1 Fig. 2 NOTES DURING THE FORCED EJECTION 1.
  • Page 6: Boards Connection

    2. BOARDS CONNECTION Connector Connector (CN606, 42P) (CN603, 42P) RD-064 board RD51-RD relay board (J-6090-167-A) RD51-AV extension flexible flat cable (J-6090-168-A) RD51-AV relay board (J-6090-169-A) Connector (CN502, 42P) Connector (CN501, 42P) — 6 —...
  • Page 7: General

    BE LIABLE FOR ANY top of a hot surface, such as a recorder for a long time, be AMOUNTS REPRESENTING Sony is not liable and will not VCR or amplifier (receiver). sure to disconnect the recorder LOSS OF PROFITS, LOSS OF compensate for any lost •...
  • Page 8: Quick Guide To Disc Types

    Usable disc versions (as of August 2006) Quick Guide to Disc Types • 8x-speed or slower DVD+RWs • 6x-speed or slower DVD-RWs (Ver.1.1, Ver.1.2 with CPRM • 16x-speed or slower DVD+Rs Recordable and playable discs • 16x-speed or slower DVD-Rs (Ver.2.0, Ver.2.1 with CPRM •...
  • Page 9: Hookups And Settings

    Step 1: Connecting the Aerial Cable and Set Top Box Hookups and Settings Controller Hooking Up the Recorder Select one of the following aerial hookups. Do NOT set “Line3 Input” of the “Scart Setting” to “Decoder” in the “Video” setup (page 103) when making connection A or B. Follow steps 1 through 6 to hook up and adjust the settings of the recorder.
  • Page 10: Step 2: Connecting The Video Cords/Hdmi Cord

    C: Connecting the aerial cable only (no set top box receiver) Step 2: Connecting the Video Cords/HDMI Cord Use this hookup if you watch cable programme position without a cable box. Also use this Select one of the following patterns, A through E, according to the input jack on your TV hookup if you are connecting just an aerial antenna.
  • Page 11: Step 3: Connecting The Audio Cords

    SYSTEM Sanyo MENU Notes Thomson M/m, • If the supplied remote interferes your other Sony ENTER Toshiba DVD recorder or player, change the command mode number for this recorder (page 23). The remote performs the following: • Use the batteries correctly to avoid possible leakage and corrosion.
  • Page 12: Step 6: Easy Setup

    Select “Others,” and press ENTER. To check the Command Mode for the Press ENTER. Step 6: Easy Setup recorder Follow the on-screen instructions to Press x on the recorder when the recorder is make the following settings. turned off. The Command Mode for the Easy Setup - OSD Make the basic adjustments by following the recorder appears in the front panel display.
  • Page 13: Connecting A Vcr Or Similar Device

    Connecting to the LINE 2 IN jacks on the front panel Connecting a VCR or Similar Device Connect a VCR or similar recording device to the LINE 2 IN jacks of this recorder. If the After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.
  • Page 14: Eight Basic Operations - Getting To Know Your Dvd Recorder

    Select “System” using </,. 2. Recording a Eight Basic Operations — Getting to Know Your DVD Recorder Programme 1. Inserting a Disc - RW - RW Video Video - RW - RW Video DATA DVD This section introduces the basic operation to Video Press M/m to select an available TV record a current TV programme to the hard...
  • Page 15: Displaying The Playing Time And Play Information

    Select a title, and press ENTER. To change the title order (Sort) To turn off the Title List 4. Displaying the Playing The sub-menu appears. While the Title List menu is turned on, press Press TITLE LIST. OPTIONS to select “Sort Titles.” Press M/m The sub-menu displays options Time and Play z Hints...
  • Page 16: Labelling And Protecting A Disc

    To use the number buttons Note 6. Labelling and 7. Playing the Disc on You can enter up to 64 characters for a DVD’s disc You can also use the number buttons to enter name. The disc name may not appear when the disc characters.
  • Page 17: Guide Plus

    z Hint Learning the common elements By reformatting, you can change the recording format on DVD-RWs, or record again on DVD- GUIDE Plus+ RWs that have been finalised. Press TV GUIDE. Introduction to the The GUIDE Plus+ system “Home Screen” Note appears.
  • Page 18: Searching For A Programme Using The Guide Plus

    Select a programme using M/m, and z Hints • Press the PAGE buttons to change the Searching for a Listing Up Your Favourite press ENTER. programme list by page. Programme using the Programme Information • Press the DAY +/– buttons to change the programme list by day.
  • Page 19: Timer Recording

    To cancel the settings Note Changing the GUIDE Plus+ host To receive from the recorder a programme position Press the red button (“Back”). that can be received by either the set top box channel manually receiver or the recorder, change the input source in To return to the “Home”...
  • Page 20: Timer Recording (Guide Plus+/Showview/Manual)

    Press TV GUIDE. To adjust the recording quality Recording TV programmes Timer Recording (GUIDE See step 3 of “Adjusting the recording picture using the ShowView system quality and size” on page 60. Plus+/ShowView/ Rec. Mode Adjust Manual) The ShowView system is a feature that If there is not enough available disc space for simplifies setting the timer.
  • Page 21: Checking/Changing/Cancelling Timer Settings

    Notes “HDD Rec. Picture Size”/“DVD Rec. Adjusting the recording picture Checking/Changing/ • If one programme contains two picture sizes, the Picture Size”: selected size is recorded. However, if the 16:9 Sets the picture size of the programme to quality and size Cancelling Timer signal cannot be recorded as 16:9, it is recorded as be recorded.
  • Page 22: Playback

    Press INPUT SELECT repeatedly to Notes Press the pause (or play) button on the Recording from connected • The recorder starts recording only after detecting select “L3.” connected equipment to cancel the a special control signal from the connected equipment without a timer playback pause status.
  • Page 23 Select an item, and press ENTER. Notes Playback options • Angles and subtitles cannot be changed with titles The adjustment display appears. recorded on this recorder. “FNR” (frame noise reduction): • Slideshows made with a DVD camcorder can To check the position of the buttons below, see the illustration on page 66. Reduces noise contained in the only be played.
  • Page 24: Searching For A Title/Chapter/Track, Etc

    Press H. The display for entering the number Searching for a Title/ Playing MP3 Audio appears. For MP3 discs, playback starts from the Example: Title Search first MP3 audio track on the disc. Chapter/Track, etc. Tracks, JPEG Image For JPEG files, a slideshow of the ®...
  • Page 25: Erasing And Editing

    Notes • Depending on the software you use to create the DATA DVD/DATA CD, the playback order may Erasing and Editing differ from the above illustration. • No more than a total of 999 individual folders can Before Editing be played. (Folders that do not contain JPEG/ MP3/DivX files are counted as well.) •...
  • Page 26: Creating And Editing A Playlist

    Press ENTER if point A is correct. Dividing a title (Divide) Creating chapters manually Creating and Editing a If point A is incorrect, select point A using c/C, and press ENTER. The Playlist - RW - RW display for setting point B appears. If you want to dub a long title to a disc but do You can manually insert a chapter mark at Select point B using...
  • Page 27: Dubbing (Hdd T Dvd)

    z Hint Notes After titles are combined, the title name is the title • You cannot make a recording while dubbing. Dubbing (HDD y DVD) name of the first title prior to combination. • To play a dubbed disc on other DVD equipment, finalise the disc (page 41).
  • Page 28: Dubbing

    Select “Dub Mode.” : Indicates titles containing Dubbing multiple titles (Dub Dubbing “Copy-Once” copy protection Select a dubbing mode using M/m. Selected Titles) signals (page 87). When you select Fast* a title with , the display asks - RW - RW Video A maximum of 30 selected titles can be for confirmation.
  • Page 29: Recording An Entire Dv Format Tape

    z Hints Press INPUT SELECT on the remote Notes Recording an Entire DV • You cannot connect more than one piece of • If you set “Finalise Disc” of “One Touch repeatedly to select “DV.” digital video equipment to the recorder. Dubbing”...
  • Page 30: Settings And Adjustments

    Channel Select “Programme Setting” in “Basic,” Press M/m repeatedly until the programme and press ENTER. Select “On” to turn on AFT. Settings and Adjustments position you want is displayed. Turns on the Auto Fine The programme positions are scanned in the Tuning function.
  • Page 31: Video Settings (Video)

    z Hint Notes 16 : 9 Video Settings (Video) • In step 4 above, enter “000” if you do not want to If you set “Auto Adjust” to “On,” the Auto Clock use the TV guide page number for automatic Set function is activated whenever the recorder is labelling.
  • Page 32: Audio Settings (Audio)

    Audio Connection Note • 48kHz/96kHz PCM (DVD VIDEOs only) Audio Settings (Audio) If the HDMI OUT jack is connected to equipment Selects the sampling frequency of the audio The following setup items switch the method not compatible with DOLBY DIGITAL signals, the signal.
  • Page 33: Disc Settings (Dvd)

    Changes the Command Mode of the recorder if other DVD equipment is assigned the same Command Mode. For details, see “If you have a Sony DVD player or more than one Sony DVD recorder” on page 23. Registration Code Displays the registration code of DivX video files for this recorder.
  • Page 34: Additional Information

    (page 101). , You have set the recorder to progressive Sony dealer. Connect the TV and the recorder using a TV channels cannot be changed. format even though your TV cannot accept , The channel is disabled (page 97).
  • Page 35 Mechanical sound is heard when the display. The remote does not function. recorder is off. , Contact your Sony dealer or local You dubbed a title, but the title did not , Batteries are weak. , While the recorder is adjusting the clock for authorized Sony service facility.
  • Page 36: Self-Diagnosis Function (When Letters/Numbers Appear In The Display)

    IEEE 1394 data transport bus proposed by SONY, and is Hard disk drive capacity: 160 GB a trademark approved by many corporations. Required i.LINK cable Mass (approx.): 4.7 kg...
  • Page 37: Guide To Parts And Controls

    Front panel Guide to Parts and Controls For more information, see the pages in parentheses. Remote J TV/DVD button (22) K TOP MENU/Red button (66) L CHAPTER MARK/Yellow button (81) CHAPTER MARK ERASE/Blue A [/1 (on/standby) button (25) K HDD button/indicator (33) button (81) DVD button/indicator (33) B Front panel display (126)
  • Page 38 MEMO 1-32E...
  • Page 39: Disassembly

    RDR-HX820/HX825 SECTION 2 DISASSEMBLY NOTE: The following flow chart shows the disassembly procedure. Case block assembly (Page 2-2) Tray assembly RD-064 board Hard disk section D. C. fan (Page 2-3) (Page 2-2) (Page 2-4) (Page 2-5) Hard disk (Page 2-5) DVD drive (Page 2-6) Power block...
  • Page 40: Case Block Assembly

    NOTE: Follow the disassembly procedure in the numerical order given. 2-1. CASE BLOCK ASSEMBLY 3 Three special front point screws 4 Case block assembly 2 Two tapping screws 1 Two tapping screws 2-2. RD-064 BOARD 5 Five tapping screws 4 Flexible flat cable (+BV 3 x 8) (FRD-011) (CN201) q;...
  • Page 41: Tray Assembly

    2-3. TRAY ASSEMBLY Hole 3 Two claws The stiff wire Tray assembly Open the tray. 2-4. FRONT PANEL ASSEMBLY 1 Seven claws 2 Front panel assembly...
  • Page 42: Board, Fr-257 Board

    2-5. FL-166 BOARD, FR-257 BOARD 2 Connector (CN3101) 5 FL-166 board 3 Three tapping screws (+BV 3 x 8) (CN3102) (CN3001) 4 FL cover 1 Flexible flat cable 6 Flexible flat cable (FLR-008) (FAR-005) (CN3003) 7 Connector (CN3005) 8 Three tapping screws 9 FR-257 board (+BV 3 x 8) 2-6.
  • Page 43: Hard Disk

    2-7. HARD DISK 6 Remove the HDD shield plate in the direction of the arrows A and B . 5 Hard disk section 4 HDD bracket (5.5) 2 Harness 7 Hard disk (PH-077) 3 Four screws 2-8. D. C. FAN 4 Remove the D.C.
  • Page 44: Dvd Drive

    2-9. DVD DRIVE 4 Four tapping screws 8 DVD drive (+BV 3 x 8) 5 Remove the DVD section in the direction of the arrow A . 2 Connector (CN2) 7 Flexible flat cable (FRD-011) 3 Flexible flat cable (FRD-011) (CN201) 6 Two tapes 1 Pin 2-10.POWER BLOCK...
  • Page 45: Av-106 Board

    2-11.AV-106 BOARD 3 Four tapping screws (+BV 3 x 8) 4 RD bracket 5 Pin 7 Pin 2 Tapping screw (+BV 3 x 10) 1 Two large type clamps 6 Pin 8 Connector (CN103) qd Connector qf Five tapping screws (CN3) (+BV 3 x 8) 9 Connector...
  • Page 46: Circuit Boards Location

    2-12.CIRCUIT BOARDS LOCATION Power block AV-106 board FL-166 board RD-064 board FR-257 board 2-8E...
  • Page 47: Block Diagrams

    RDR-HX820/HX825 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM J702 LINE 2 OUT S VIDEO VIDEO AUDIO L AUDIO R RD-064 BOARD AV-106 BOARD TMDS DATA,CLOCK IC904 CN902 IC702 IC902 HDMI HDMI TX VIDEO AMP SELECTOR SCALER IC901 TU401 J703 AERIAL TUNER TU VIDEO...
  • Page 48: Block Diagram

    RDR-HX820/HX825 3-2. AV-106 BLOCK DIAGRAM AV-106 BOARD IC702 WIDE SELI (6/8) J702 VIDEO AMP CVBS OUT LINE 2 OUT SELECTOR C OUT S VIDEO S-Y OUT 27 CVBS1 VIDEO Y2 IN C-Y OUT 25 C2 IN AUDIO L V2 IN Cb OUT CVBS3 TU401...
  • Page 49: 1/2) Block Diagram

    RDR-HX820/HX825 3-3. RD-064 (1/2) BLOCK DIAGRAM (1/8) (1/8) RD-064 BOARD FR-257 BOARD FL-166 BOARD(2/2) IC103 IC102 RISM3 EEPROM 2 VOUT AT1DATA0 D4,B3,D3,B2 CN201 CN603 B1,C1,D1,E3 RECVY Q607 RECVY IC3101 E4,D2,C2,A1 IC3002 RECCCR Q606 RECCR IDE D0-D15 A2,C3,A3,C4 AT1DATA15 CN3003 FLD DRIVE REMOTE COMMANDER SIRCS RECIEVER...
  • Page 50: 2/2) Block Diagram

    RDR-HX820/HX825 3-4. RD-064 (2/2) BLOCK DIAGRAM RD-064 BOARD(2/2) IC904 (8/8) REC656O 1 AD14,AB14 SCALB[0-7] HDMI TH AC15,AB15 AC16,AD17 TMDS DATA 2+ TX2+ AD18,AB17 REC656O 7 TMDS DATA 2- TX2- TMDA DATA 1+ TX1+ SCALY[0-7] TMDS DATA 1- TX1- TMDS DATA 0+ PXCLK AB16 DCLK...
  • Page 51: Power Block Diagram

    RDR-HX820/HX825 3-5. POWER BLOCK DIAGRAM SWITCHING REGULATOR RD-064 BOARD IC601 (SRV-2001EK) 1V REG T101 CN606 L602 L601 SW 5V SW1V SWITCHING CN101 F101 D101 TRANSFORMER T3.15/250V MAIN RECT Q301 D301 L301 12V REG D304 P301 2A IC502 UNSW 4V AC IN IC101 FLASH SW12V...
  • Page 52 RDR-HX820/HX825 MEMO 3-11 3-12E...
  • Page 53: Schematic Diagrams

    RDR-HX820/HX825 SECTION 4 SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 4-1. FRAME SCHEMATIC DIAGRAM CN103 3P FAN_OUT FAN_DET CN3 15P CN101 15P UNSW12V UNSW12V UNSW6V UNSW6V AV-106 BOARD UNSW6V UNSW6V UNSW6V UNSW6V SW5V SW5V POWER UNSW6V UNSW6V UNSW4V UNSW4V UNSW4V UNSW4V UNSW4V UNSW4V UNSW-8V...
  • Page 54: Schematic Diagrams

    RDR-HX820/HX825 4-2. SCHEMATIC DIAGRAMS WAVEFORMS AV-106 RD-064 THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS BOARD BOARD (In addition to this, the necessary note is printed in each block) X602 J703 COMPONENT P X201 (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µµF. 50V or less are not indicated except for electrolytics and tantalums.
  • Page 55 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-43 for printed wiring board. AV-106 BOARD(1/8) POWER NO MARK:REC/PB MODE -REF.NO.: 10,000 SERIES- PS102 0.63A CN101 UNSW5V-V JL101 R160 GND-V R135 JL102 TO(6/8) UNSW12V JL103 UNSW-8V-V R137 UNSW-8V-V UNSW6V GND-V JL104 TO(7/8) UNSW6V UNSW6V-A...
  • Page 56 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-43 for printed wiring board. CN502 JL539 SPDIFO AV-106 BOARD(2/8) NO MARK:REC/PB MODE SPDIFO JL540 XLMUTE XLMUTE AUDIO IN JL538 C213 SPD_GND R218 R223 -REF.NO.: 10,000 SERIES- AUGND ± 0.5% ± 0.5% AUGND JL548 EU-AU-OUT- R...
  • Page 57: 3/8) (Audio Out)

    RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-43 for printed wiring board. AV-106 BOARD(3/8) NO MARK:REC/PB MODE SIGNAL PATH AUDIO OUT VIDEO SIGNAL -REF.NO.: 10,000 SERIES- R310 AUDIO 5100 R320 ± 0.5% 2200 CHROMA Y/CHROMA SIGNAL AOUTR- R323 R311 C313 5600 5100...
  • Page 58 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-43 for printed wiring board. (TUNER) TU401 SIGNAL PATH AV-106 BOARD(4/8) VIDEO SIGNAL AERIAL AUDIO TUNER CHROMA Y/CHROMA SIGNAL -REF.NO.: 10,000 SERIES- IC401 10 11 12 14 15 16 17 NO MARK:REC/PB MODE 30V REG...
  • Page 59 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-43 for printed wiring board. TU_AFT TU_AFT TU_G_MAX TU_G_MAX AV-106 BOARD(5/8) TU_AUTOP TO(8/4) TU_AUTOP TU_PCONT IT CONTROLLER TU_PCONT CN602 JL668 -REF.NO.: 10,000 SERIES- IT_GND R674 IT_GND JL669 R675...
  • Page 60: 6/8) (Video In/Out)

    RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-43 for printed wiring board. AV-106 BOARD(6/8) VIDEO IN/OUT SIGNAL PATH NO MARK:REC/PB MODE -REF.NO.: 10,000 SERIES- R :REC MODE VIDEO SIGNAL P :PB MODE AUDI O CHROMA Y/CHROMA...
  • Page 61: 7/8) (Euro In/Out)

    RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-43 for printed wiring board. JL801 TU_SDA TO(4/8, AV-106 BOARD(7/8) JL803 5/8,6/8) TU_SCL JL802 EURO IN/OUT -REF.NO.: 10,000 SERIES- TO(2/8,5/8) C802 IC801 NO MARK:REC/PB MODE TK11250CMCL-G IC801 R :REC MODE VCONT R845 P :PB MODE 5V REG VOUT...
  • Page 62 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-43 for printed wiring board. AV-106 BOARD(8/8) (RDR-HX825) IR-CONT RESET5V -REF.NO.: 10,000 SERIES- IC1102 NO MARK:REC/PB MODE IC1102 M30263M6A-1547U5 R1144 IR CONT P10.1/AN1 AVss R1101 P10.2/AN2...
  • Page 63: Fl Driver,Line2 In,Power Sw

    RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-47 for printed wiring board. ND3101 (FLUORESCENT INDICATION TUBE) FL-166 BOARD FL DRIVER,LINE2 IN,POWER SW -REF.NO.: 30,000 SERIES- 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 NO MARK:REC/PB MODE : Voltage measurement of...
  • Page 64: Dv, Remocon Receiver, Function Sw, Led

    RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-49 for printed wiring board. FR-257 BOARD DV,REMOCON RECEIVER,FUNCTION SW,LED -REF.NO.: 30,000 SERIES- NO MARK:REC/PB MODE R3005 2200 R3003 Q3002 R3004 MSB709-RT1 IC3001 LEDIM 4700 SWITCH LED DRIVER R3008 Q3001 C3001 MUN2211T1 0.01u SWITCH IC3001...
  • Page 65 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-51 for printed wiring board. R124 R126 R1068 RD-064 BOARD(1/8) IC102 2200 2200 M24C32-WMN6T(B) R146 R143 4700 R127 4700 XSYSRST TO(2/8,3/8,4/8,5/8,6/8) RISM3 ± 0.5% 2200 ± 0.5% R1052 C1031 -REF.NO.: 20000SERIES- R122 C1030 0.1u 0.1u...
  • Page 66 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-51 for printed wiring board. RD-064 BOARD(2/8) HDD DRIVE NO MARK:REC/PB MODE -REF.NO.: 20,000 SERIES- SIGNAL PATH RB210 RB211 RB212 RB213 VIDEO SIGNAL AUDI O CHROMA Y/CHROMA SIGNAL...
  • Page 67 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-51 for printed wiring board. RD-064 BOARD(3/8) REC656V V DEC REC656H -REF.NO.: 20,000 SERIES- NO MARK:REC/PB MODE R:REC MODE C328 C333 P:PB MODE 0.1u 0.1u C330 C331 REC656I[0]...
  • Page 68 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-51 for printed wiring board. RD-064 BOARD(4/8) FLASH ROM -REF.NO.: 20,000 SERIES- NO MARK:REC/PB MODE NORHOE NORHOE : Voltage measurement of the CSP IC HCS[0] HCS[0] and the Transistors with mark, is not possible.
  • Page 69 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-51 for printed wiring board. C620 220p CN603 AGND JL616 RD-064 BOARD(5/8) SPDIFO JL617 FB606 XLMUTE XLMUTE AV-CN/POWER NO MARK:REC/PB MODE R :REC MODE -REF.NO.: 20,000 SERIES- SPD_GND JL618 P :PB MODE AUGND L604 AUGND...
  • Page 70 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-51 for printed wiring board. RD-064 BOARD(6/8) DV-PHY NO MARK:REC/PB MODE -REF.NO.: 20,000 SERIES- XSYSRST (1/8,2/8,3/8 4/8,5/8) PHYLPS PHYLREQ C705 C710 R733 0.01u 0.01u R709 R713 R705 CN701...
  • Page 71 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-4 for waveforms. • Refer to page 4-51 for printed wiring board. IC802 IC802 RD-064 BOARD(7/8) ICS650G-42LFT R823 C806 PLL/AUDIO-AD-DA 0.01u REF27M3 R830 REF27M2 -REF.NO.: 20,000 SERIES- C807 768FSOH C810 TO(8/8) X1_IN R825 R821 0.01u...
  • Page 72 RDR-HX820/HX825 For Schematic Diagram • Refer to page 4-51 for printed wiring board. R942 IC907 IC908 1.8V REG RD-064 BOARD(8/8) 3.3V REG C946 0.01 C950 HDMI 0.01 NO MARK:REC/PB MODE R1913 R :REC MODE -REF.NO.: 20,000 SERIES- P :PB MODE R1929 SW3.4VC R1927...
  • Page 73 RDR-HX820/HX825 SWITCHING REGULATOR (SRV-2001EK) C112 680p L105 250V L106 T101 Q301 P301 D301 SWITCHING TRANSFORMER L301 2SJ438 L302 D304 SF5LC20U 3.7uH 12V REG 10uH 11EQS06 13.6 12.5 D101 Q302 S1WBA60B R104 C106 C301 R303 2SJ599 CN1 4P 100k 1000p/1kV R301 1000p 12V SW 12.1...
  • Page 74 RDR-HX820/HX825 4-3. PRINTED WIRING BOARDS LINE 2 OUT DIGITAL OUT AERIAL • : Uses unleaded solder. COMPONENT IN-OUT VIDEO OUT Y-PB/CB-PR/CR S VIDEO VIDEO L-AUDIO-R OPTICAL COAXIAL G-LINK LINE3/DECODER HX825 only LINE1-TV AV-106 BOARD (SIDE A) AV-106 BOARD (SIDE A) CN101 D-1 CN103 C-1 CN501 F-7...
  • Page 75 RDR-HX820/HX825 AV-106 BOARD (SIDE B) • : Uses unleaded solder. AV-106 BOARD (SIDE B) D608 D702 D1103 D305 R1709 JL915 JL714 D702 JL913 D714 C848 JL408 R1417 JL726 JL724 JL838 D731 D715 R1115 D813 C324 JL841 C1404 C1405 D724 D714 JL731 JL733 JL823...
  • Page 76 RDR-HX820/HX825 FL-166 BOARD (SIDE A) • : Uses unleaded solder. FL-166 BOARD (SIDE A) CN3101 B-2 C3117 D3112 B-1 IC3101 A-4 T3101 ND3101 C3120 IC3101 (ON/STANDBY) S3101 C3114 C3106 L3101 LINE 2 IN J3101 AUDIO L CN3101 (MONO) S VIDEO VIDEO AUDIO R R3120...
  • Page 77 RDR-HX820/HX825 • : Uses unleaded solder. FR-257 BOARD (SIDE A) CN3004 B-4 D3007 S3013 S3012 CN3005 B-5 D3001 B-5 SYNCHRO REC D3002 A-4 D3003 A-3 D3003 D3002 D3004 A-6 D3005 D3004 D3005 A-7 IC3002 A-5 S3001 S3004 S3003 S3006 S3002 (REC STOP) (OPEN/CLOSE) (PLAY)
  • Page 78 RDR-HX820/HX825 • : Uses unleaded solder. NOM-JIG C701 CN501 S501 CN506 RD-064 BOARD (SIDE A) RESET CN201 C-7 IC902 R535 C506 R533 R534 C820 CN701 B-8 IC903 R532 R524 R431 S601 CN901 D-3 IC907 R835 CN902 D-1 IC908 C807 IC801 C818 IC804 IC909...
  • Page 79 RDR-HX820/HX825 • : Uses unleaded solder. RD-064 BOARD (SIDE B) RD-064 BOARD (SIDE B) CN603 D-3 JL504 JL512 CN606 E-5 JL566 JL511 JL519 JL526 D915 R518 R513 R561 C509 R562 JL556 JL569 JL572 JL559 JL562 JL547 JL565 JL567 C401 R537 JL564 C101 JL541...
  • Page 80: Ic Pin Function Description

    RDR-HX820/HX825 SECTION 5 IC PIN FUNCTION DESCRIPTION 5-1. IT CONTROL IC (IC603: M306H5MG-A14FP, M306H5MC-C36FP (AV-106 BOARD)) Pin No. Pin Name Function ONDO Detection of board temperature SIRCSIN Input of remote control signal AVLINK-IN Input of AV LINK scart signal FLD_DATA Output of FLD data signal FLD_IN Fixed at “L”...
  • Page 81 Pin No. Pin Name Function P_FAIL Input of UNSW6V power off detection signal HDET_1 Detection of IN SEL output video signal Fixed at “L” (when the flash is overwritten is VCC) Not used INSEL_PCONT Output of IC’s power supply signal (“H”:INSEL) XP_AMUTE Output of muting signal for audio Not used...
  • Page 82 Pin No. Pin Name Function TU_G_MAX_1 Input of tuner gain control signal VREF Power supply input (Analog 5V) AVCC Power supply input (Analog 5V) Not used START Input of oscillation selection signal SYNCIN Input composite video signal SVREF When slice the vertical synchronous signal input slice power TEST2 Fixed at GND VDD3...
  • Page 83: Main Control Ic (Ic103: R8A34012Bg (Rd-064 Board))

    5-2. MAIN CONTROL IC (IC103: R8A34012BG (RD-064 BOARD)) Pin No. Pin Name Function AT1DATA[11] Input/output of data 11 for DVD AT1DATA[12] Input/output of data 12 for DVD AT1DATA[14] Input/output of data 14 for DVD AT1DIOW Output of DVD write signal AT1INTRQ Input of IRQ signal HDREQ[0]...
  • Page 84 Pin No. Pin Name Function VCCAAD10A — Power supply input (Analog 3.3V)(ADC) VROA — Fixed at “L” VROB — Fixed at “L” VCCAAD10B — Power supply input (Analog 3.3V)(ADC) VCCADA10 — Power supply input (Analog 3.3V)(DAC) VCCADA10 — Power supply input (Analog 3.3V)(DAC) AB10 VCCADA10 —...
  • Page 85 Pin No. Pin Name Function VSSADA10 Analog GND BOUT(PD2) Output of analog video signal (blue) VSSADA10 Analog GND AD10 COUT(PD3) Output of analog video signal (chroma) AD11 TESTMOD[2] — Digital GND AD12 TESTMOD[7] — Digital GND AD13 Fixed at “H” AD14 REC656O[0] Not used...
  • Page 86 Pin No. Pin Name Function HADRS[31] Output of address 31 HADRS[27] Output of address 27 HADRS[23] Output of address 23 HADRS[20] Output of address 20 HADRS[16] Output of address 16 HADRS[12] Output of address 12 HADRS[8] Output of address 8 MSBS —...
  • Page 87 Pin No. Pin Name Function HADRS[18] Output of address 18 HADRS[14] Output of address 14 HADRS[9] Output of address 9 MSINS — Fixed at “L” SCLK[2] Output of reset signal for HDMI sub-CPU CTS[2] Output of UART(CSIO)/GPIO TX[0] Output of UART(CSIO)/GPIO TX[3] Input of IO HDMI sub-CPU SI signal RX[3]...
  • Page 88 Pin No. Pin Name Function Digital GND CSYNC — Fixed at “H” HDATA[6] Input/output of data 6 HDATA[3] Input/output of data 3 HDATA[2] Input/output of data 2 AT2DATA[0] Input/output of data 0 for HDD driver AT2DATA[15] Input/output of data 15 for HDD driver AT2DMARQ Input of request signal from DMA AT2DIOW...
  • Page 89 Pin No. Pin Name Function AT2DATA[8] Input/output of data 8 for HDD driver Digital GND Digital GND Digital GND Digital GND Digital GND Digital GND — Power supply input (Digital 1.0V) DDATA[30] Input/output of data 30 for SDRAM DDATA[31] Input/output of data 31 for SDRAM VDD25 —...
  • Page 90 Pin No. Pin Name Function VDD25 — Power supply input (Digital 2.5V) Digital GND DDATA[16] Input/output of data 16 for SDRAM DDATA[17] Input/output of data 17 for SDRAM AOLRCKI Input of audio L/R clock signal DACCLKO Not used SPDIFI Fixed at “H” PHYDIO[7] Input of data 7 for PHY Digital GND...
  • Page 91 Pin No. Pin Name Function Digital GND 5-12E...
  • Page 92: Service Mode

    RDR-HX820/HX825 SECTION 6 SERVICE MODE This is the diagnostics to locate cause of fault. The diagnostics can be executed using the remote commander and a monitor. To enter the service mode, connect the VIDEO OUT connector of the main unit to the monitor. While pressing the “A” (Open/Close) button and the “G”...
  • Page 93: Screen Transition In The Service Mode

    MODEL SYSCON Version [ < RETURN > HDD Serial ID [ Setting ON/OFF of the PAL 100% white signal output HDD Sony ID [ << Display Color >> 1) White Signal ON < 2 > 2) White Signal OFF < RETURN >...
  • Page 94: Items And Description Of Service Mode Menu

    When the key “8” is pressed down, the monitor display moves HDD Serial ID [ to the hard disk check menu screen. Sony ID [ When the key “9” is pressed down, the monitor display moves to the hard disk check menu screen.
  • Page 95: Hdd Service Mode

    6-5. HDD service mode 1) When the key “1” is pressed down, the ID check will be << HDD MODE >> executed as shown below. 1) Indicate ID Indicate ID : HDD information read-out 2) Peformance Check MODEL : Model name of the product 3) Write ID Serial No.
  • Page 96: Adjustments

    RDR-HX820/HX825 SECTION 7 ADJUSTMENTS 7-1. Video System Adjustment 2. S-Video Output S-Y Check <Purpose> This check confirms that the S-video Y-signal output has the rated Preparing for Adjustment amplitude. If it adjusted incorrectly, the playback video signal will 1. Equipments not be displayed corrected even when the S-video cable is connected.
  • Page 97 3. S-Video Output S-C Check 5. Component Video Output B-Y (Pb) Check <Purpose> <Purpose> This check confirms that the S-video output S-C conforms to the This check confirms that the B-Y signal of the component video PAL standard. If it adjusted incorrectly, the playback color will not conforms to the PAL standard.
  • Page 98 7. Scart Video Output Level Check 9. Scart Video Output S-C Check <Purpose> <Purpose> This check is made to satisfy the PAL signal standard, If it is adjusted This check confirms that the Scart output S-C conforms to the PAL incorrectly, brightness will be too bright or too dark.
  • Page 99 11. Scart Video RGB Output G Check <Purpose> This check confirms that G signal of the RGB video conforms to the PAL standard. If this signal level is not correct, color of the video signal will have different color when the Scart connector output signal is connected to a projector having Scart input.
  • Page 100: Repair Parts List

    RDR-HX820/HX825 SECTION 8 REPAIR PARTS LIST 8-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one. in the exploded views are not supplied.
  • Page 101: Chassis Section-1

    8-1-2. CHASSIS SECTION-1 supplied not supplied supplied Chassis section-2 not supplied (See page 8-3) Ref. No. Part No. Description Remarks 3-088-023-01 +B3 (3-CR) 3-077-331-31 +BV3 (3-CR) 3-077-331-01 +BV3 (3-CR) * 54 A-1494-643-A RD-064 BOARD, COMPLETE (SERVICE) (HX820) * 54 A-1215-024-A RD-064 BOARD, COMPLETE (SERVICE) (HX825)
  • Page 102: Chassis Section-2

    8-1-3. CHASSIS SECTION-2 supplied not supplied supplied not supplied not supplied supplied TU401 not supplied supplied supplied supplied not supplied not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-077-331-01 +BV3 (3-CR) 1-833-388-11 CABLE, FLEXIBLE FLAT (FAR-005) 3-087-675-01 6-32UNCX5 1-787-291-11 FAN, D.C 0 103...
  • Page 103: Electrical Parts List

    AV-106 8-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, uH: µH please include the board name. parts list may be different from the parts specified in the diagrams or the components •...
  • Page 104 AV-106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C620 1-162-923-11 CERAMIC CHIP 47PF C732 1-107-826-11 CERAMIC CHIP 0.1uF C621 1-107-826-11 CERAMIC CHIP 0.1uF C733 1-107-826-11 CERAMIC CHIP 0.1uF C622 1-162-923-11 CERAMIC CHIP 47PF C734 1-107-826-11 CERAMIC CHIP 0.1uF C623 1-107-826-11 CERAMIC CHIP...
  • Page 105 AV-106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C842 1-107-826-11 CERAMIC CHIP 0.1uF * CN701 1-770-468-21 PIN, CONNECTOR (PC BOARD) 10P C843 1-165-908-11 CERAMIC CHIP C844 1-165-908-11 CERAMIC CHIP < DIODE > C845 1-164-230-11 CERAMIC CHIP 220PF C846 1-164-230-11 CERAMIC CHIP...
  • Page 106 AV-106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < FERRITE BEAD > < COIL > FB701 1-414-228-11 INDUCTOR, FERRITE BEAD L102 1-419-630-21 INDUCTOR 4.7uH FB702 1-414-228-11 INDUCTOR, FERRITE BEAD L401 1-414-856-11 INDUCTOR 10uH FB801 1-500-283-11 INDUCTOR, FERRITE BEAD L402 1-469-967-21 INDUCTOR 10uH...
  • Page 107 AV-106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q807 6-550-683-01 TRANSISTOR RJK005N03-T146 R316 1-216-825-11 METAL CHIP 2.2K 1/10W Q808 8-729-027-24 TRANSISTOR DTA114TKA-T146 R317 1-216-825-11 METAL CHIP 2.2K 1/10W Q1104 8-729-045-17 TRANSISTOR 2SB1561T100Q (HX825) R318 1-216-825-11 METAL CHIP 2.2K 1/10W Q1401...
  • Page 108 AV-106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R619 1-216-833-11 METAL CHIP 1/10W R683 1-216-833-11 METAL CHIP 1/10W R620 1-216-833-11 METAL CHIP 1/10W R684 1-216-864-11 SHORT CHIP R621 1-216-833-11 METAL CHIP 1/10W R685 1-216-809-11 METAL CHIP 1/10W R622 1-216-833-11 METAL CHIP...
  • Page 109 AV-106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R808 1-216-845-11 METAL CHIP 100K 1/10W R1105 1-216-821-11 METAL CHIP 1/10W R809 1-216-809-11 METAL CHIP 1/10W (HX825) R810 1-216-809-11 METAL CHIP 1/10W R1106 1-216-825-11 METAL CHIP 2.2K 1/10W R819 1-216-809-11 METAL CHIP...
  • Page 110 AV-106 FL-166 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1610 1-216-809-11 METAL CHIP 1/10W C3114 1-128-131-11 ELECT 22uF R1613 1-216-837-11 METAL CHIP 1/10W C3115 1-115-339-11 CERAMIC CHIP 0.1uF R1614 1-216-833-11 METAL CHIP 1/10W C3116 1-107-726-91 CERAMIC CHIP 0.01uF R1621 1-216-839-11 METAL CHIP...
  • Page 111 FL-166 FR-257 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R3115 1-216-838-11 METAL CHIP 1/10W < SWITCH > R3116 1-216-845-11 METAL CHIP 100K 1/10W S3001 1-771-410-21 SWITCH, TACTILE (PLAY) < SWITCH > S3002 1-771-410-21 SWITCH, TACTILE (REC STOP) S3003 1-771-410-21 SWITCH, TACTILE (REC) S3101...
  • Page 112 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C144 1-125-777-11 CERAMIC CHIP 0.1uF C219 1-164-943-81 CERAMIC CHIP 0.01uF C145 1-125-777-11 CERAMIC CHIP 0.1uF C220 1-164-943-81 CERAMIC CHIP 0.01uF C146 1-125-777-11 CERAMIC CHIP 0.1uF C222 1-137-710-11 CERAMIC CHIP 10uF 6.3V C147...
  • Page 113 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C606 1-137-710-11 CERAMIC CHIP 10uF 6.3V C915 1-128-934-91 CERAMIC CHIP 0.33uF C607 1-137-710-11 CERAMIC CHIP 10uF 6.3V C916 1-125-777-11 CERAMIC CHIP 0.1uF C608 1-107-826-11 CERAMIC CHIP 0.1uF C917 1-127-772-81 CERAMIC CHIP 33000PF...
  • Page 114 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks * C1038 1-112-833-11 ELECT CHIP 68uF IC902 6-706-520-01 IC CXD9836R C1041 1-125-777-11 CERAMIC CHIP 0.1uF IC903 6-806-931-01 IC MB95F108ASPFV-GE1-5G00 IC906 6-703-046-01 IC SN74LVC1G08DCKR < CONNECTOR > IC907 6-707-119-01 IC TK11218CMCL-G IC908 6-704-470-01 IC TK11233CMCL-G...
  • Page 115 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R138 1-218-973-11 RES-CHIP 1/16W R205 1-218-990-81 SHORT CHIP R139 1-218-973-11 RES-CHIP 1/16W R206 1-218-990-81 SHORT CHIP R140 1-218-973-11 RES-CHIP 1/16W R207 1-218-941-81 RES-CHIP 1/16W R141 1-218-973-11 RES-CHIP 1/16W R208 1-218-990-81 SHORT CHIP...
  • Page 116 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R337 1-218-965-11 RES-CHIP 1/16W R703 1-218-935-11 RES-CHIP 1/16W R338 1-218-990-81 SHORT CHIP R705 1-218-965-11 RES-CHIP 1/16W R513 1-218-965-11 RES-CHIP 1/16W R706 1-218-953-11 RES-CHIP 1/16W R518 1-218-965-11 RES-CHIP 1/16W R709 1-218-941-81 RES-CHIP...
  • Page 117 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R935 1-218-941-81 RES-CHIP 1/16W R1031 1-218-935-11 RES-CHIP 1/16W R937 1-218-990-81 SHORT CHIP R1032 1-218-935-11 RES-CHIP 1/16W R938 1-218-961-11 RES-CHIP 4.7K 1/16W R1033 1-218-933-11 RES-CHIP 1/16W R939 1-218-990-81 SHORT CHIP R1035 1-218-933-11 RES-CHIP 1/16W...
  • Page 118 RD-064 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R1934 1-218-953-11 RES-CHIP 1/16W RB159 1-234-400-21 CONDUCTOR, NETWORK (2010X4) R1935 1-218-953-11 RES-CHIP 1/16W RB171 1-234-380-21 RES, NETWORK 47K (1005X4) R1936 1-218-953-11 RES-CHIP 1/16W RB172 1-234-380-21 RES, NETWORK 47K (1005X4) R1940 1-218-929-11 RES-CHIP 1/16W...
  • Page 119 RD-064 POWER SUPPLY BLOCK Ref. No. Part No. Description Remarks < VIBRATOR > X201 1-813-210-11 VIBRATOR, CRYSTAL (NX5032GA) 25MHz X301 1-781-940-41 VIBRATOR, CRYSTAL 14.318MHZ * X701 1-813-695-11 VIBRATOR, CRYSTAL 24.576MHZ X801 1-781-867-21 VIBRATOR, CRYSTAL 27MHz X901 1-795-244-11 VIBRATOR, CERAMIC 10MHz ************************************************************ 1-474-022-11 POWER SUPPLY BLOCK (SRV-2001EK) ********************************...
  • Page 120 RDR-HX820/HX825 Sony Corporation 2006H1600-1 Home Electronics Network Company 9-883-932-11 ©2006.08 — 154 — Published by Quality Assurance Dept.

This manual is also suitable for:

Rdr-hx820

Table of Contents