DSC Power PC5532Z Instruction Manual page 44

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security
Controls Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interfer-ence in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference to radio or television
reception, which can be deter-mined by turning the equipment off and on, the user is en-
couraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is available from the U.S.
Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following Control Units:
PC580, PC1555MX, PC5010, PC5015, PC5020 or the NT9005.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules and, if the product was ap-
proved July 23, 2001 or later, the requirements adopted by the ACTA. On the side of
this equipment is a label that contains, among other information, a product identifier. If
requested, this number must be provided to the Telephone Company.
PC580 Product identifier: US: F53AL01BPC580
PC1555MX Product identifier US:F53AL01BPC1555
PC5010 FCC Registration# F53CAN-22839-AL-E; REN=0.1B
PC5015 FCC Registration# F53CAN-32104-AL-E; REN=0.6B
PC5020 FCC Registration# F53CAN-34330-AL-E; REN=0.1B
NT9005 FCC Registration# F53CAN-36358-AL-E; REN=0.1B
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this prod-
uct. It is designed to be connected to a compatible modular jack that is also compliant.
See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a tele-
phone line. Excessive RENs on a telephone line may result in the devices not ringing in
response to an incoming call. In most but not all areas, the sum of RENs should not ex-
ceed five (5.0). To be certain of the number of devices that may be connected to a line,
as determined by the total RENs, contact the local Telephone Company. For products
approved after July 23, 2001, the REN for this product is part of the product identifier
that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN
without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is sep-
arately shown on the label.
Incidence of Harm
If this equipment (PC580, PC1555MX, PC5010, PC5015, PC5020 or the NT9005)
causes harm to the telephone network, the telephone company will notify you in ad-
vance that temporary discontinuance of service may be required. But if advance notice
is not practical, the Telephone Company will notify the customer as soon as possible.
Also, you will be advised of your right to file a complaint with the FCC if you believe
it is necessary.
©2003 Digital Security Controls Ltd.
Toronto, Canada •
Printed in Canada Imprimé au Canada Impreso en Canadá
www.dsc.com
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the Tele-
phone Company will provide advance notice in order for you to make necessary modi-
fications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (PC580, PC1555MX, PC5010, PC5020
and the NT9005), for repair or warranty information, please contact the facility indicat-
ed below. If the equipment is causing harm to the telephone network, the Telephone
Company may request that you disconnect the equipment until the problem is solved.
This equipment is of a type that is not intended to be repaired by the end user.
Simplex Time Recorder Co. 100 Simplex Drive, Westminster MA 01441-0001 USA,
Tel: (978) 731-2500
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
Alarm dialing equipment must be able to seize the telephone line and place a call in an
emergency situation. It must be able to do this even if other equipment (telephone, an-
swering system, computer modem, etc.) already has the telephone line in use. To do so,
alarm dialing equipment must be connected to a properly installed RJ-31X jack that is
electrically in series with and ahead of all other equipment attached to the same tele-
phone line. Proper installation is depicted in the figure below. If you have any questions
concerning these instructions, you should consult your telephone company or a quali-
fied installer about installing the RJ-31X jack and alarm dialing equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider's
RJ-31X
Facilities
Jack
Alarm Dialing
Equipment
Telephone
Line
Network
Demarcation
Telephone
Point
Answering
System
Computer
Unused
RJ-11 Jack
Telephone
Unused
Fax Machine
RJ-11 Jack
Telephone