Table of Contents
Advertisement
Output of Black-White/Colour switching signal
It is possible to output black-white/colour switching signal from the AUX terminal on the back
of this unit. Perform the following settings.
MENU button
SET button
SET
CAMERA
SETUP
AWC
MENU
B&W/COLOUR MODE
B&W
AUT O
AUTO L E V E L
NORMAL
MODE S EL E C T
CAMERA T I T L E ED I T
. .
RE V ERS E MODE
OF F
H L I M O D E
O F F
AL M . T I T L E S Z E
I
DOUBLE
AL ARM COLOUR
WH I T E
AU X T E R M I N A L
(B&W IN)
D. Z O O M M A X
x2
CAUTION:
When you use near infrared ray illumi-
nations, use a lens that is compatible
with the near infrared ray illuminations.
Any lens other than the compatible one
can result in out-of-focus due to such
characteristics.
E-40
Set the B&W Item to AUTO.
1.
Select the B&W/COLOUR MODE item
on the ALC SETTING screen.
2.
Press the SET button.
The B&W/COLOUR MODE screen
appears.
3.
Press either the
button or the
button and select the B&W item.
4.
Press either the
button or the
button and set to "AUTO".
5.
Upon completion of setting, press the
MENU button twice.
Then, the MAIN MENU screen is
brought back.
Set the AUX TERMINAL Item to
B&W OUT.
1.
Select MODE SELECT on the MAIN
MENU screen.
2.
Press the SET button.
The MODE SELECT screen appears.
3.
Press either the
button or the
button and select the AUX TERMINAL
item.
4.
Press either the
button or the
button and set to "B&W OUT".
5.
Upon completion of setting, press the
MENU button twice.
• Then, the normal screen is brought
back.
MEMO
• When you use infrared illumination, if the
subject excessively reflects, a B/W screen
can switch to a colour screen.
To perform switching with higher accuracy,
we recommend that you use it by the setting
mentioned in [Control by Black-White/
Colour Switching Signal From the Outside],
referring to Page 41.
Control by Black-White/Colour switching signal from the outside
Carry out the following setting when you link in motion the black-white/colour switching of this
unit and infrared illumination, etc., using the switching signal from the outside control device.
+
-
B&W: Make signal
1
2
COLOUR: Break
signal
TX+ TX- RX+ RX- AUX GND
A
B
C
D
Y/C OUT
SYNC IN
VIDEO OUT
SEE INST-
RUCTION
POWER
MANUAL
It is requested that you consult our JVC dealer about connecting
devices, etc.
MENU button
SET button
SET
CAMERA
SETUP
AWC
MENU
A C SE T
L
T
I NGS
I
R S L E VE L
I
NORMAL
A E
V RA E
G : P EAK
8 2
:
S UT
H
T ER E x DR
/
N RMAL
O
A C
G
MODE
2 d B
0
L L U
O
X MODE
O F
F
S NS
E
E U P
O F
F
P
R
I O
R I T Y
MO
T I ON
B C
L
E D
I
T 1
B&W/COLOUR MODE . .
B&W/COLOUR MODE
B&W
AUT O
AUTO L E V E L
NORMAL
Infrared illumination, etc.
Switching
signal
Sensor or switch
Outside control device
Set the B&W item to AUX.
1.
Select B&W/COLOUR MODE on
the ALC SETTING screen.
2.
Press the SET button.
• The B&W/COLOUR MODE screen
appears.
3.
Press either the
button or the
button and select the B&W
item.
4.
Press either the
button or the
button and set to "AUX".
Then, the AUX TERMINAL item on the
MODE SELECT screen is automatically
set to (B&W IN). Refer to
Page 33.
5.
Upon completion of setting,
press the MENU button.
• Then, the ALC SETTING screen is
brought back.
CAUTION:
When you use near infrared ray illumi-
nations, use a lens that is compatible
with the near infrared ray illuminations.
Any lens other than the compatible one
can result in out-of-focus due to such
characteristics.
E-41
Advertisement
Table of Contents
