Page 1
900/1400 GAS-FIRED SERIES OPERATING INSTRUCTIONS AND PARTS MANUAL OPERATOR’S MANUAL 89144050-1 ® ® FOR TECHNICAL ASSISTANCE OR THE HOTSY DEALER NEAREST YOU, CONSULT OUR WEB PAGE AT WWW.HOTSY.COM 8.914-405.0...
Page 2
969SS SPECIFICATIONS 952SS SPECIFICATIONS ● Pump Volume At Pump Head: 3.8 GPM/228 GPH ● Pump Volume At Pump Head: 3.8 GPM/228 GPH ● Pump Pressure At Pump Head: 2300 PSI ● Pump Pressure At Pump Head: 2300 PSI ● Burner Type: Natural Gas Fired, 364,835 BTU/Hr. ● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.
Page 3
992SS SPECIFICATIONS 1412SS SPECIFICATIONS ● Pump Volume At Pump Head: 3.9 GPM/234 GPH ● Pump Volume At Pump Head: 3.9 GPM/234 GPH ● Pump Pressure At Pump Head: 2000 PSI ● Pump Pressure At Pump Head: 3000 PSI ● Burner Type: Natural Gas Fired, 364,835 BTU/Hr. ● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.
Page 4
1462SS-208 SPECIFICATIONS 1424SS SPECIFICATIONS ● Pump Volume At Pump Head: 3.9 GPM/234 GPH ● Pump Volume At Pump Head: 3.9 GPM/234 GPH ● Pump Pressure At Pump Head: 3000 PSI ● Pump Pressure At Pump Head: 3000 PSI ● Burner Type: Natural Gas Fired, 364,835 BTU/Hr.
The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. /11...
9. Eye, hand, and foot protection WHEN OPERATING phase this product should only be connected to a must be worn when using this THIS EQUIPMENT. power supply receptacle protected by a GFCI. equipment. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
Do not use liquid fuel. Have a qualified stream at people, or severe in- RISK OF INJECTION serviceman install and service your equipment. OR SEVERE INJURY jury or death will result. TO PERSONS. KEEP CLEAR OF NOZZLE. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
Page 8
WARNING: If connection is made to portable water supply, a back flow device must be provided. Follow the maintenance instructions specified in the manual. Example Of Down Draft Diverter For Gas Fired Machines HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
Detergent Metering Valve — Controls detergent Adjustable Thermostat — Prevents water tempera- mixture. ture from exceeding high temperatures. Is not used to maintain constant temperature setting. Wand — Must be connected to the spray gun. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
Install pressure hose on machine as shown. Assemble wand components as shown. Connect pressure hose to trigger gun. NOTE: The nozzle is not to be installed at this time. Relief Valve Pressure Hose HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
Operate only where Hotsy is not a licensed contractor and as such we are open flame or torch is permitted. unable to make recommendations for suitable make and CAUTION - RISK OF ASPHYXIATION: Do not run model of power vents.
Extension Cords: Do not use extention cords with this equipment. WARNING: To reduce the risk of electrocution, keep all connections dry and off the ground. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
For the best results, Wash from the bottom to the top, using side to side contact your Hotsy dealer to help you select the best motions. This washes away heavy dirt and allows the detergent for your application.
• Clean filter screen on detergent inlet line periodi- cally. • Flush the pressure washer system with antifreeze if storing for an extended period of time; refer to Storage for details. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
Gas valve switch in OFF position Place switch in ON position. HOT WATER Inadequate fuel supply Check fuel supply. Pump switch turned off Pump must be running before burner will light. HOTSY • 900-1400 • 8.914-405.0 GAS FIRED • Rev. 8/11b...
IMPORTANT If the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identified by visiting www.hotsy.com. When ordering from your dealer, please provide the following:...
Page 20
Hotsy does not authorize any other party, including authorized Hotsy Distributors, to make any representation or promise on behalf of Hotsy, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of Hotsy products conforms to local codes.
Page 21
If you are looking for replacement parts for your Hotsy, please contact your local dealer. You can find a dealer by calling Hotsy at 800-525-1976 or by visiting www.hotsy.com.
Page 22
If you need service on your pressure washer, contact your local Hotsy dealer or visit www.Hotsy.com. Smart phone users scan the code below to link directly to the Service Request page. Form #8.914-405.0 • Revised 8/11b • Printed in U.S.A.