Remote Control - JVC TM-2001U User Manual

Connections
Connecting to a Camcorder
You may connect a camcorder to your television by using the front Input Jacks (Input 2). You may
also connect a game console or other equipment using these jacks. Camcorders may also be
connected to the television's rear input jacks.
INPUT 2
VIDEO L MONO AUDIO R
Illustration of TM-2701SU
1) Connect the yellow video cable out from the Camcorder's Video Output, in to the TV's Video
Input jack.
2) Connect the white audio cable out from the Camcorder's Left Audio Output, in to the TV's Left
Audio Input Jack.
3) Connect the red audio cable out from the Camcorder's Right Audio Output, in to the TV's
Right Audio Input Jack.
• If your Camcorder is a mono sound model it will have only one audio jack. Connect it to the
TV's Left Audio Jack.
Headphone Connection (available on 20 inch models)
You can connect a pair of headphones or earphone to the television using the headphone jack on the front
panel.
1) Plug a headphone/earphone jack into the headphone jack on the television's front panel.
14
Remote Control Basics
•
Before you can operate the remote control, you must first install
the batteries (included). See "Changing the Batteries" at the
bottom of this page for instructions. (For an illustration, please see
TV CATV VCR DVD
POWER
page 7.)
•
Press the P
OWER
•
Make sure the TV/CATV switch is set to TV. Move the switch to
INPUT
CATV only if you need to operate a cable box.
VIDEO STATUS 1 2 3
•
Slide the VCR/DVD selector switch to VCR to control a VCR,
slide to DVD to control a DVD player. Please see pages 16 to
4 5 6
18 for instructions on programming your remote control to
operate a Cable box, VCR or DVD player.
DISPLAY 7 8 9
•
Press the CH+ and CH- buttons to scan through the channels.
0
SLEEP TIMER 100+ RETURN+
Tap the CH+ or CH- button to move through the channels one
channel at a time.
HYPER SURROUND
RM-C306 •
To move rapidly through the channels using JVC's Hyperscan
feature, press and hold CH+ or CH-. The channels will zip by at
MUTING V CHIP
a rate of five channels per second.
+
CH
•
Press V + or V
OL
VOL VOL
+
bar will appear onscreen to show you the television volume
level.
C H
MENU EXIT
•
The CH+/- and V
onscreen menu system.
VCR CHANNEL VCR/DVD
POWER
PREV NEXT TV/VCR
•
You can directly access specific channels using the 10-key pad.
REW PLAY FF
•
For more information on remote control button features, see
STOP PAUSE pages 38 to 41. For information on using the onscreen menus,
REC
see page 19.
OPEN/CLOSE STILL/PAUSE
Notes: Remote control model RM-C306 is shown at the left.
A different model remote control may have come with your
television.
TV
Changing the Batteries
Push down on the remote's back cover and slide towards the bottom to remove it.
Insert two AA batteries (supplied), carefully noting the "+" and "-" markings on the batteries and on the remote
control. To avoid a potential short circuit, insert the "-" end first. Be sure to use only size AA batteries.
When batteries are installed, slide the cover back into place (until it clicks into position).
• If the remote control acts erratically, replace the batteries. Typical battery life is six months to one
year. We recommend using alkaline batteries for longer battery life.
When you change the batteries, try to complete the task within three minutes. If you take longer than three
minutes, the remote control codes for your VCR, DVD, and/or Cable Box may have to be reset (page 16-18).

Remote Control

button to turn the television on or off.
- to raise or lower the volume. An indicator
OL
+/- buttons are also used to navigate JVC's
OL
15