CHAUVET® owns the content of this user manual in its entirety, including but not Copyright limited to pictures, logos, trademarks, and resources.
Page 3
Fuse Power In/Out Rear View Top View Data In/Out 13.43 in 341 mm 14.49 in 368 mm 11.69 in 297 mm 10.63 in 270 mm 3.86 in 98 mm 8.86 in 225 mm 13.31 in 338 mm Clamp Safety Cable Floor Mounting Overhead Mounting Table of Contents...
Page 5
Static Control....................................Auto/Custom Programs ................................11 Edit Custom Programs ................................12 Master/Slave ....................................12 Fixture Cloning ................................... 13 Fan Control ....................................13 Pan/Tilt Speed.................................... Reverse Pan Direction ................................13 Reverse Tilt Direction ................................. 13 Optics Speed....................................Reverse Dimmer Direction ................................. 13 Head Motion Black Out ................................
In addition, keep the box and contents for inspection. For other issues, such as missing components or parts, damage not related to shipping, or concealed damage, file a claim with CHAUVET® within 7 days of delivery. Manual...
Page 7
This product contains no user-serviceable parts. Any reference to servicing in this user manual will only apply to properly trained CHAUVET® certified technicians. Do not open the housing or attempt any repairs. All applicable local codes and regulations apply to proper installation of this product.
In case of a serious operating problem, stop using this product immediately! In the unlikely event that your CHAUVET® product may require service, contact CHAUVET® Technical Support. LEDs gradually decline in brightness over time, mostly because of heat. Packaged in...
The listed current rating indicates the maximum current draw during normal operation. For more information, you may download Sizing Circuit Breakers from the CHAUVET® website: www.chauvetpro.com. Always connect this product to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.
If you need more information about DMX standards, Master/Slave connectivity, or the DMX cables needed in order to link the product to a DMX controller, download the DMX Primer from the CHAUVET® website: www.chauvetpro.com. Before mounting this product, read and follow the Safety Notes.
CHAUVET® recommends using the following general guidelines when mounting this Rigging product. When selecting an installation location, consider easy access to this product for operation, programming adjustments, and routine maintenance. Make sure to mount this product away from any flammable material as...
Control Panel Button Function Description MENU Exits from the current menu or function Enables the currently displayed menu or sets the currently selected value in to the current function ENTER Navigates upward through the menu options and increases the numeric value when in a function DOWN Navigates downward through the menu options and decreases the numeric value when in a function You can set the Q-Wash™...
This setting enables you to activate or disable the control panel lock, which keeps Control Panel non-authorized personnel from changing the product’s settings. Lock To secure the SETTINGS level only: 1. Go to SERVICE > ACCESS > SETTINGS LOCK. a. Select ON to require the password to access the level or OFF to allow open access.
This setting controls how the product will respond when the DMX signal is Loss of Signal lost. Setting 1. Go to the SETTINGS > PERFORM level, and select DMX ERROR. a. Select SAVE to make the product use the last command used when the signal is lost.
This setting allows the programming of up to 49 steps in the CUSTOM running Edit Custom mode. Programs 1. Go to STAND ALONE > EDIT. 2. Select STEP. 3. Set the program step (01~49). a. Select PAN or TILT. i. Set the position value (000~255). ii.
The Q-Wash™ 419Z-LED gives you 3 ways in which to transfer the settings from 1 Fixture Q-Wash™ 419Z-LED to other Q-Wash™ 419Z-LED products when hooked up via Cloning DMX daisy chain configuration. To transfer the CUSTOM program only: 1. Go to STAND ALONE > SEND. a.
Color The Color setting determines how the product generates the white color based on various RGB settings. Settings 1. Go to the SETTINGS > PERFORM main level. 2. Select COLOR. 3. Select OFF, RGBtoW, or UC. OFF: When all the RGB faders are set to 255, the output is maximum, although the resulting white color may not be balanced.
Limit Pan/Tilt 1. Select SETTINGS > RANGE. Range 2. To set the start and end points of the pan and tilt ranges: a. Select P.START and set the pan starting point between 000~255. b. Select P.END and set the pan ending point between 000~255. c.
The Q-Wash™ 419Z-LED gives you 3 different levels to reset the product. Reset To reset the Pan and Tilt motors only: 1. Go to MANUAL > RESET > PT.RESET. a. Select YES to reset or NO to exit. To reset the Zoom motor only: 2.
Page 22
Selects the fan’s operation mode. SETTINGS PERFORM FANS SLOW NORM FAST AUTO PT SPEED FAST Defines the speed of the pan/tilt SLOW PAN INVERT NORM Defines the direction of the pan fader INVERT TILT INVERT NORM Defines the direction of the tilt fader INVERT OPTICS SPEED FAST...
Page 23
SETTINGS PERFORM NORM Defines the direction of the dimmer fader (cont.) (cont.) INVERT INVERT COLOR Universal color balance RGB set to “255” = balanced white RGBtoW RGB set to “255” = max. output SAVE Continues with last command upon loss of ERROR DMX control BLACK...
Page 24
RANGE P.START 000~255 Sets the pan start point (pan range) P.END Sets the pan end point (pan range) T.START Sets the tilt start point (tilt range) T.END Sets the tilt end point (tilt range) Activates the changes DISPLAY LOCK Activates/deactivates the main level password DEFAULT **** (Enter Password)
Page 25
EDIT STEP 01~49 Selects the program step 000~255 Selects the pan position TILT Selects the tilt position Combines red, green, blue, and white to obtain a custom color GREEN BLUE WHITE DIMMER Selects the dimmer value STROBE Selects the strobe frequency ZOOM Select the zoom position TIME...
Page 26
MANUAL MANUAL 000~255 Allows manual control of all settings from (cont.) control panel TILT GREEN BLUE WHITE DIMMER STROBE ZOOM SERVICE CALIB.M 000~255 Calibrates the start position of the motors TILT ZOOM CALIB.C 3200K 000~255 Sets color temperature for White 1 GREEN BLUE WHITE...
Page 27
3400K Sets color temperature for White 2 GREEN BLUE WHITE 4200K Sets color temperature for White 3 GREEN BLUE WHITE 4900K Sets color temperature for White 4 GREEN BLUE WHITE 5600K Sets color temperature for White 5 GREEN BLUE WHITE Sets color temperature for White 6 5900K GREEN...
Page 28
SERVICE CALIB.C 6500K 000~255 Sets color temperature for White 7 (cont.) (cont.) GREEN BLUE WHITE Sets color temperature for White 8 7200K GREEN BLUE WHITE 8000K Sets color temperature for White 9 GREEN BLUE WHITE Sets color temperature for White 10 8500K GREEN BLUE...
BLUE ACCESS SETTINGS Activates/deactivates the SETTINGS main level LOCK password SERVICE Activates/deactivates the SERVICE main level LOCK password CONTENT DISPLAY1 ********* Allows 16 characters of text to be displayed on control panel DISPLAY2 ********* SEND Sends CONTENT settings of the 1st product to all other Q-Wash™...
Page 30
DMX Values (Cont.) Channel Function Value Percent/Setting PERSON2 000 255 0~100% Pan Fine 000 255 0~100% Tilt 000 255 0~100% Tilt Fine 000 255 0~100% Pan/Tilt Speed 000 255 0~100% 000 255 0~100% Red Fine 000 255 0~100% Green 000 255 0~100% Green Fine 000 255...
Page 31
Auto Rings No Function Static Ring 1 Static Ring 2 Static Ring 3 Ring Effect 1 Ring Effect 2 Ring Effect 3 Ring Effect 4 Ring Effect 5 Ring Effect 6 Ring Effect 7 Ring Effect 8 Ring Effect 9 Ring Effect 10 Ring Effect 11 Ring Effect 12...
Page 32
Zoom 0~100% Control No Function Pan/tilt black activation Pan/tilt black deactivation Automatic fan speed Slow fan speed Normal fan speed High fan speed Auto program 1 (3 s activation delay) Auto program 2 (3 s activation delay) Test (3 s activation delay) Custom program (3 s activation delay) No Function Reset (3 s activation delay)
Page 33
Control 000 019 No Function 020 039 Pan/tilt black activation 040 059 Pan/tilt black deactivation 060 079 Automatic fan speed 080 099 Slow fan speed 100 119 Normal fan speed 120 139 High fan speed Auto program 1 (3 s activation delay) 140 149 Auto program 2 (3 s activation delay) 150 159...
Page 34
Green 2 000 255 0~100% Blue 2 000 255 0~100% White 2 000 255 0~100% Red 3 000 255 0~100% Green 3 000 255 0~100% Blue 3 000 255 0~100% White 3 000 255 0~100% DMX Values (Cont.) Channel Function Value Percent/Setting PERSON5...
Channel Function Value Percent/Setting PERSON5 (cont.) Red 2 000 255 0~100% Red 2 Fine 000 255 0~100% Green 2 000 255 0~100% Green 2 Fine 000 255 0~100% Blue 2 000 255 0~100% Blue 2 Fine 000 255 0~100% White 2 000 255 0~100% White 2 Fine...
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be the customer’s responsibility. FedEx packing or double-boxing are recommended. CHAUVET® reserves the right to use its own discretion to repair or replace returned product(s). Technical Specifications...
Page 37
Type Power Lifespan Light Source 15 W 50,000 hours Color Quantity Current quad-color RGBW Photo Optic Parameter Narrow Wide Illuminance @ 5 m 3,046 lx 743 lx Beam angle 7º 25º Field angle 16º 37º Thermal Max. External Cooling System Temperature 104 °F (40 °C) Fan-Assisted...
Page 38
World Headquarters United Kingdom and Ireland Contact CHAUVET® CHAUVET® Europe Ltd. General Information General Information Address: 5200 NW 108th Avenue Address: Unit 1C Sunrise, FL 33351 Brookhill Road Industrial Estate Voice: (954) 577-4455 Pinxton, Nottingham, UK Fax: (954) 741-5571 NG16 6NT...