Initial Battery Charge; Assembly Instructions - Peg-Perego CHOO CHOO express train IGED1116 Use And Care Manual

INITIAL BATTERY CHARGE

!• Remove battery and charger from packaging. Connect battery charger to a 120vac wall recepticle. Connect battery
charger to battery.
WARNING:
ADULT ASSEMBLY REQUIRED. USE CARE WHEN UNPACKING AS COMPONENTS TO BE ASSEMBLED MAY
POSE A SMALL PARTS/SHARP EDGE HAZARD.
BATTERY ALREADY INSTALLED IN VEHICLE.
1 • Snap-fit the end of the funnel, which is included in the packaging.
2 • Loosen the screw on the front of the seat.
3 • Remove the seat by lifting the front part (1) and pulling out the back part (2).
4 • Remove the battery charger from the compartment under the seat.
5 • Connect the battery plug (A) to the system plug (B).
6 • Put the seat back into place, inserting the back part first (1) and then the front part (2).
7 • Fasten the seat with the screw. The vehicle is ready for use.
8 • The product can operate both with and without the track. Assemble the track as shown in the figure. For best results, position the train on the track so that it
travels anticlockwise.
9 • To use the train off the track, remove the screw on the coupling lock as shown in the figure.
10 • Turn the lock around and put it back, as shown in detail A of the figure. Secure the lock with the screw. To use the product on the track again, it is necessary to
return it to its original state.
11 • OPERATION BUTTONS: Press button A to play the tunes. Press the button again to change the tune. To start the train, press button B: the headlight and the
sound effects will also automatically come on.
12 • ARMRESTS: Pull the seat out as shown above. Unhook and remove the armrests (see figure). Put the seat back into place and fasten it with the screw.
13 • FIGURE 8 CONVERSION TRACK SET OPTION: The kit for the Figure 8 Track includes 6 bends, 4 straight pieces of track, and 4 intersections. By adding the
12 bends that come with the train, the track will make a figure eight.
14 • When you purchase an OPTIONAL FIGURE 8 CONVERSION TRACK SET, you can also make the OVAL FIGURE using the 4 pieces of straight track.
15 • To assemble the FIGURE 8 TRACK, place a piece of intersection over another piece, as shown in the figure.
16 • Add a second piece of track.
17 • To fasten the last piece of the intersection, turn the first and last piece slightly, as shown in the figure.
18 • Complete the track by adding the remaining pieces.
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING IT FROM THE TOY.
19 • Remove the seat. Loosen the screw and remove the fake coal from the back of the seat.
20 • Unfasten the screw fixing the battery holder and take it out. Unfasten the connectors (system-battery).
21 • Replace the battery (1). Remove the central peg from the battery holder, pressing the tabs at the end of the peg to do so (2). Replace the battery holder,
inserting it first into one opening and then into the other (3), as shown in the figure.
22 • Screw the battery holder back into place. Join the two connectors.
23 • Put the fake coal back into place.
24 • Fasten the fake coal with the screw and put the seat back into place, as shown above. Fasten the seat with the screw.
25 • Disconnect plug A (the electrical system plug) from plug B (the battery plug) by pressing on the sides of the plugs.
26 • Connect plug B to plug C (the battery charger plug). Connect the battery charger to a household electrical outlet, following the instructions supplied with the
battery charger.
27 • When the battery is completely charged, disconnect the battery charger from the outlet and disconnect plug C from plug B.
28 • Connect plug B to plug A, pressing until it clicks into place.
29 • Always remember to put the seat back into place and to fasten it with a screw.

ASSEMBLY INSTRUCTIONS

FEATURES AND INSTRUCTIONS FOR USE
OPTION
BATTERY REPLACEMENT
BATTERY RECHARGER