General Operations - Clarity CCE203DAB Instruction Manual

General Operations

Reset the unit
The RESET button is to be activated for the
following reasons:
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
1.Turn off the unit power.
2.Press the OPEN
the front panel and remove it, then press
the RESET button with a ballpoint pen or
similar object to restore the unit to the
original factory settings.
Note:
if you press RESET
work yet, please use a cotton swab soaked
in isopropyl alcohol to clean the socket on
the front panel.
Power on/off
In power off mode, switch on the unit by
pressing any button except the
button and the EJECT
inserting a disc into the slot When the
system is on, press the
to turn off the unit.
Sound adjustment
- Rotate the VOLUME/SELECT
adjust volume level.
- Press the VOLUME/SELECT
repeatedly to select the sound setting that
you would like to adjust: volume, bass,
treble, balance or fader. Rotate the
VOLUME/SELECT
level of the selected sound mode:
- VOL: from 00 to 100 (50 levels)
- BAS (bass) / TRB (treble): from -10 to +10
- BAL (Balance): 10L, 9L, ~,L=R, ~, 9R,
10R. Note: L = left, R = right.
- FAD (Fader): 10F, 9F, ~, F=R, ~, 9R, 10R.
Note: F=front; R= rear.
Note:
In each mode, when the unit has not been
adjusted for about 5 seconds, the current
setting will be saved and it will return to the
previous mode.
System setup menu
Press the VOLUME/SELECT
hold for more than 2 seconds to access the
( ) button to flip down
button, the unit can't
OPEN
( ) button or
.
POWER ( ) button
button to
button
button to adjust the
button and
system setup menu mode, then press the
VOLUME / SELECT
menu item in sequence as follows:
"TA SEEK or TA ALARM"
MUTE"
"MASK DPI or MASK ALL"
DAB-FM N"
BEEP OFF"
After selecting the desired menu item,
rotate the
make the adjustment.
"TA SEEK or TA ALARM"
announcement/traffic announcement
alarm)
- TA SEEK mode:
When a newly tuned station does not
receive traffic information for 5 seconds,
the radio retunes to next station which has a
different PI and which broadcasts traffic
information.
If, during the chosen retune time (30
( )
seconds for a short retune or 90 seconds for
a long retune), the unit can no longer
receive the current station which was
broadcasting traffic information, it will start
to search for the next station that has the
same PI.
If no station with the same PI is found after
one search cycle, the radio will search for
the next station broadcasting traffic
announcements.
- TA ALARM mode:
Select this mode to switch off the automatic
retune. The radio will then emit a double
beep sound (ALARM).
If a newly tuned station does not broadcast
any traffic information for 5 seconds, a beep
can be heard.
If the unit can no longer receive the current
station during the chosen retune time, a
beep sound can also be heard.
If a newly tuned station has no RDS signal,
the message "PI SEEK" disappears.
Note: TP: Traffic Program.
"PI SOUND or PI MUTE":
In some regions, there is a possibility of
having two different stations with the same
frequency but different PI codes.
If "PI SOUND" is selected, radio will switch
to the new station with a different PI for a
button to select the
g
g
"RETUNE L or RETUNE S"
g
ND
"BEEPS 2 , BEEP ALL,
VOLUME/SELECT
PI: Program Identification.
"PI SOUND or PI
g
g
"DAB-FM Y or
button to
(search for traffic