To Add Or Reprogram A Remote Control - Chamberlain GS400D Owner's Manual

To Add or Reprogram a Remote Control

1. Press LEARN XMITTER button and release (LED will
light up).
2. Press remote button, the LED will flash, alarm output
will activate twice.
3. Repeat steps 1 and 2 until all remote controls are
programmed (9 remote controls maximum).
NOTE: For highest level of security, we recommend the
Security ✚
® line of products. Refer to Accessories.
To Add a Wireless Keyless Entry (not provided
see Accessory page)
1. Press LEARN XMITTER button and release (LED will
light up).
2. Enter a four digit personal identification number (PIN)
of your choice on the keypad.
3. Then press enter, the LED will flash, alarm output will
activate twice.
TO ERASE ALL CODES
To deactivate any unwanted remote controls or keyless
entries, first erase all codes:
Press and hold the LEARN XMITTER button on control
board until the learn indicator light goes out (approximately
6 seconds). All previous codes are now erased.
Reprogram each remote control or keyless entry you wish
to use.
To prevent possible SERIOUS INJURY or DEATH from a
moving gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or door.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
AVERTISSEMENT
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
ATTENTION
Remote Control LEARN XMITTER Button
LEARN
XMITTER
R1
D27
ADVERTENCIA
C11
PRECAUCIÓN
39
WARNING WARNING
CAUTION
K6
ALARM
NO
LEARN
C
XMITTER
K5
MAGLOCK
GATE 1
NO
L1
BRN
C
GRN
NC
R2 ON
WHT
Z1
R1
YEL
10A 32V
BLU
F3
GATE 1
RED
D1Ø
K2
DIAGNOSTIC
GATE 2
ACCESSORY
POWER
K1 Q9
Z12
FORCE
BRN R9Ø
GRN
ACCESSORY
OVLD
WHT 24V
R1Ø1
YEL
BRN R1ØØ
BLU
F4
GRN
10A 32V
RED
WHT
GATE 2
YEL
BLU
R35
RED
K3 D9
D8 C12
GATE 2 Z3
Z4
Q22 D22
C11
D15
R4 C2 R196
24 VAC/
SOLAR
INPUT
MOV2
J4 R9
MOV1
OPEN EDGE/
R223
CLOSE
EDGE
R2Ø7
Z2 Ø
R227
PHO T O
R224
Z22
U4
R92
Z9
OPEN
PHO T O
R91
R94
Z8
CLOSE
PHO T O
R93
TIMER TO
CLOSE
COM
OVLD
CONTROL
INPUTS
OPEN
SINGLE BUTTON
RESET
STOP
OFF MAX
COM
COM
POWER
F7 LOOP
INPUTS
C13 C4
SHADOW
U3
INTERRUPT
CHGR COM
OVLD
F6
F2
F1 20A 32V
D4
Programming