Related Manuals for Banner American BA-FS27
Summary of Contents for Banner American BA-FS27
- Page 1 OPERATING INSTRUCTIONS FINISHER 2700 Model No. BA-FS27 Banner American Products, Inc. abcoffice 800-658-8788 www.abcoffice.com...
-
Page 2: Table Of Contents
Table of Contents Get to Know Your Laminator ......1-2 For Your Safety ..........3 III. Electrical Safeguards ........3-4 Specifications ..........4 Set-up .............. 4-6 Inspection ............4 Appropriate Location ........4 Accessories ............. 4 Loading Film onto Mandrels ......5 Threading the Film ........... -
Page 3: Get To Know Your Laminator
I. Get to Know Your Laminator... Upper Supply Upper Idler Bar Mandrel Upper Mandrel Safety Shield Holder Emergency Stop Button Emergency Stop Button Right Control Panel (see below) Left Control Panel (see below) Feed Table Guide Motor Lower Supply Tie Bar Mandrel Lower Mandrel Lower Idler Bar... - Page 4 Roller Pressure Adjustment Front Rear OPEN OPEN turn turn clockwise clockwise CLOSE CLOSE turn turn counter- counter- clockwise clockwise To Open the Rollers: Pull out the pin and turn handle clockwise until it will not turn any farther and the pin locks into place. To Mount: From the OPEN position, pull out the pin and turn handle counter-clockwise until pin locks into place.
-
Page 5: For Your Safety
II. For your Safety... Do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. Read all safety messages located in this instruction manual and on the laminator very care- fully. -
Page 6: Specifications
Do not operate the laminator with a damaged power supply cord or plug. Replace fuses only with same type rated 30A, 240V and 1A, 250V fuses. Contact your dealer for replacement fuses. There are TWO (2) EMERGENCY STOP buttons on your Finisher 2700. Pressing either one of these buttons will stop the rollers. -
Page 7: Loading Film Onto Mandrels
Feed Table Installation: Slide the feed table over the front and rear feed table holders. (The feed table weighs about 15 lbs.) Loading Film onto Mandrels The following instructions apply to poly-in film rolls as they would appear from the front of the laminator. Core Brake Gripper... -
Page 8: Mandrel Tension Adjustment
BA-FS27 Threading Diagram BA-FS27 Threading Diagram for Poly-in Rolls for Poly-out Rolls Figure 1 Figure 2 Mandrel Tension Adjustment Mandrel tension must be set correctly to ensure good lamination quality. Adjust the tension by turning the knurled knobs at both ends of the mandrels. -
Page 9: Thermal Laminating
VI. Thermal Laminating... 1. Be sure all laminator parts (i.e. safety shield, feed table, etc.) are in their proper positions and the laminating film is loaded correctly (See page 3 for film loading instructions). 2. Select the CLOSE position using the Pressure Control handle located on the right side of your Finisher 2700. -
Page 10: Coating Mount Board
7. Set the FORWARD/REVERSE switch to the FORWARD position. 8. Turn the MOTOR CONTROL ON/OFF switch to the ON position. 9. Turn the MOTOR CONTROL knob far enough to sufficiently pull a feed card into the laminator. 10. Feed the feed card between the RollerShoes™ and into the front rollers. 11. -
Page 11: Maintenance/Service
CAUTION: Heated Rollers are for warm-up only and should be turned off when operating temp- erature is reached to avoid damaging the rollers. 4. Set the temperatures according to the film manufacturer’s recommendations for the film you have chosen. The Finisher 2700 will take approximately 15 minutes to reach operating temperature. The roller and shoe temperatures are indicated on the LCD displays on the control panel. -
Page 12: Cleaning Rollershoes
7. Repeat steps 3-5 until the rollers are thoroughly clean. 8. Allow the rollers to dry completely before rethreading the laminating film. Cleaning RollerShoes™: Clean the RollerShoes™ periodically to avoid adhesive build-up. Build-up can inhibit the film from moving over the shoes smoothly. -
Page 13: Laminating & Mounting Do's & Don'ts
Laminated item curls Top or bottom film tension Loosen tension on side (top is too high or bottom) that is curling up Laminated item is wrinkled Mandrel tension too loose Increase mandrel tension on side (top or bottom) that has wrinkles Temperature too high Reduce temperature... -
Page 14: Warranty & Return Policy
Your Finisher 2700 is warranted to be free of defects in material and workmanship for a period of 1 year from the date of original purchase. In the event of a defect in materials or workmanship, Banner American Products, Inc. or its authorized dealer, will repair or replace (at their option) the laminator.