Related Manuals for Banner American BA-EN45
Summary of Contents for Banner American BA-EN45
- Page 1 OPERATING INSTRUCTIONS ENTRY 4500 Model No. BA-EN45 Banner American Products, Inc. Temecula, CA...
- Page 2 CAUTION... TO AVOID ANY DAMAGE, PLEASE DO NOT USE RAZORS OR SHARP OBJECTS NEAR THE ROLLERS.
-
Page 3: Table Of Contents
Table of Contents For Your Safety ... 2 Electrical Safeguards ... 2-3 III. Specifications ... 3 Set-up ... 3-4 Inspection ... 3 Appropriate Location ... 3 Loading Film onto Mandrels ... 3-4 Threading the Film ... 4-5 Mandrel Tension Adjustment ... 5 Thermal Laminating ... - Page 4 Entry 4500 (BA-EN45) Mandrel...
-
Page 5: For Your Safety
Keep hands and clothing away from rollers. The rollers are pinch points that can trap body parts or clothing and cause serious injury. Do not touch the front rollers while the laminator heater power is on. Turn rollers off and allow to cool. -
Page 6: Specifications
Your Entry 4500 must be placed on a sturdy table or stand in a clean, well lit area with ample space on all four sides of the laminator. Contact your dealer for the optional stand designed especially for the Entry 4500. -
Page 7: Threading The Film
With poly-out rolls the top roll will unwind from the top and the bottom roll from the bottom. Once the film is properly loaded onto the man- drels, replace the mandrels onto the laminator. Threading the Film (Figures 1&2) -
Page 8: Mandrel Tension Adjustment
Repeat this step until you obtain desired results. 4. Allow the Entry 4500 to run a small amount of film before feeding the print into the laminator to avoid a dwell line across your print. Feed the print slowly and evenly, smoothing it as the rollers pull it through. - Page 9 Rewind Option for Pressure Sensitive Laminating...
-
Page 10: Pressure Sensitive Laminating
9. Turn the MOTOR CONTROL knob far enough to sufficiently pull a feed card into the laminator. 10. Feed the feed card into the front rollers. 11. After the laminator is properly threaded and the poster board has exited the rear of the laminator, make any necessary adjustments. -
Page 11: Mounting & Laminating
VIII. Mounting & Laminating... 1. Be sure all laminator parts (i.e. safety shield, feed table, etc.) are in their proper positions and the laminat- ing film is loaded correctly (See page 3 for film loading instructions). -
Page 12: Maintenance/Service
Use the following procedure to remove any adhesive from the laminating rollers. 1. Turn the HEATED ROLLERS off and allow the laminator to cool. 2. Cut the film where it comes off the top and bottom supply rolls. Pull any film out of the laminator and away from the rollers. -
Page 13: Trouble-Shooting
3. Open the ROLLER RELEASE handle on the side of the laminator and pull the film out of the unit that has become wrapped around the rollers. 4. If you have a severe wrap-around, it may be necessary to use the REVERSE feature to back the film out. -
Page 14: Warranty & Return Policy
Your Entry 4500 is warranted to be free of defects in material and workmanship for a period of 1 year from the date of original purchase. In the event of a defect in materials or workmanship, Banner American Products, Inc. or its authorized dealer, will repair or replace (at their option) the laminator. -
Page 15: Xiii. Parts List And Illustrations
XIII. Parts List and Illustrations his section contains reference drawings and a parts list to assist you when ordering parts for your laminator. The drawings show only those parts that may be replaced by the dealer. Item Part Number 11108... - Page 16 Item Part Number 11045 4096 2379 2378 2777 11100 3032 3033 3034 8279 11167 11175 1172 11183 11184 11185 4268 11187 11188 11189 2740 2741 1326 10398 7251 1457 10878 2659 1087 2500 1450 1456 1458 2661 2828 2719 11190 1365 10837 11191...
-
Page 17: Exploded Assembly
Exploded Assembly...