Governor Gear And Shaft Service - Tecumseh ECV100 - 120 Technician's Handbook

GOVERNOR GEAR AND SHAFT SERVICE

After the cylinder cover is removed from the engine, the governor spool, gear, or governor shaft can be removed. On older
style governor assemblies, the retaining ring must be removed to allow the spool or gear to slide off the shaft. Newer style
governor shafts (3 - 6.75 model engines) use an upset to hold the governor spool on. If the gear requires replacement, the
governor shaft will have to be removed.
Governor Spool Replacement With Upset Style Governor Shaft
The spool can be replaced without removing the governor
shaft. Grip the original spool in a vise and use a twisting
and pulling motion on the flange until the spool is free.
Install the new spool by starting it on the shaft and then
turning the flange over. This will allow the weights to hang
in the proper position. Place the spool on a solid surface
and push on the flange until the spool seats. The governor
weights must be in position under the spool after
installation. (diag. 9)
Governor Gear or Shaft Replacement, Upset
Style Governor Shaft
1. Grip the original spool in a vise and use a twisting and
pulling motion on the flange until the spool is free.
2. Clamp the shaft in a vise and pound gently on the
flange with a wooden or plastic mallet to remove the
shaft.
NOTE: DO NOT TWIST THE SHAFT WHEN REMOVING.
THE SHAFT BOSS MAY BECOME ENLARGED, LEAVING
THE NEW GOVERNOR SHAFT LOOSE AND CAUSING
SEVERE DAMAGE.
3. To install a new shaft, first assemble the gear and
washer on the shaft. Start the shaft into the hole with
a few taps from a soft faced hammer.
4. Place the flange in a press with a solid piece supporting
the area below the shaft boss. Press the shaft in until
a shim, part # 670297 just becomes snug [.010 - .020
(.254 - .508 mm) clearance].
Governor Shaft Replacement, Retaining
Ring Style
1. Remove the retaining ring, spool, gear assembly, and
washers.
2. Clamp the shaft in a vise and pound gently on the
flange with a wooden or plastic mallet to remove the
shaft.
NOTE: DO NOT TWIST THE SHAFT WHEN REMOVING.
THE SHAFT BOSS MAY BECOME ENLARGED AND THE
NEW GOVERNOR SHAFT WILL BE LOOSE AND MOVE.
3. Start the new shaft into the shaft boss by tapping with
a soft faced hammer.
4. Refer to the chart at right for the proper shaft exposed
length. Add a drop of red Loctite 271 and press the
governor shaft to the proper depth using a press or a
vise. Wipe the extra Loctite off after installation (diag.
11).
5. Reassemble the governor and install the retaining ring.
28
WASHER
ENGINE MODEL
ECH90
ECV100
H 30, 35
HS 40, 50
LAV 35
LEV (all)
OHH (all)
OVRM (all)
TNT 100, 120
TVS (all)
TVM (all)
V 50, 60, 70
VH 50, 60, 70
HH 100, 120
VH 100
H 50, 60, 70
HH 60, 70
HHM80
HM 70, 80, 100
GEAR
SHIM
SHAFT BOSS
670297 (modified)
EXPOSED SHAFT LENGTH
Mounting flange to Top
1.319 - 1.334"
(33.502 - 33.883 mm)
Mounting flange to Top
1.581 - 1.596"
(25.806 - 26.314 mm)
Mounting flange to Top
1.016 - 1.036"
(25.806 - 26.314 mm)
Mounting flange to Shoulder
1.283 - 1.293"
(32.588 - 32.842 mm)
9
10
11