Table of Contents
Advertisement
2 IMPORTANT INFORMATION
2.1 Your shower is designed and tested
to the very highest standards and complies
fully with all of the relevant national/
international standards for safety and
reliability. The shower is manufactured in
a BS EN ISO 9001:2000 -registered
factory - your assurance of a quality
product.
2.2 To ensure correct use and
maintenance of the shower, please read
and adhere to the following warnings and
guidelines.
FOR INSTALLERS
2.3 The Installation must comply with the
Building Regulations Part P and the Water
Regulations. Where there is a new
installation, or a replacement product is
not identical to the one being replaced, the
cable sizes, circuit protective devices,
bonding and other requirements of the
Building Regulations must be assessed
by a (registered) qualified and competent
electrician, who should carry out the
installation taking into account the site
conditions.
2.4 WARNING: THIS APPLIANCE
MUST BE EARTHED.
2.5 Before removing your shower heater
cover always ensure your shower heater
is isolated from the electrical mains.
2.6 This product is splash-proof and is
approved for use in shower cubicles and
over baths. However, do not install the
shower heater in a position where the
handset, in its normally-parked
position, will consistently direct the
spray over it.
2.7 To
comply
with
the
Water
Regulations a servicing valve must be
fitted in the pipework to the shower, in an
accessible place. This will be of great
benefit if any maintenance work or
complete replacement of the shower is
required later on.
2.8 This shower is designed for domestic
use and is not vandal-resistant. If it is
installed in an institutional or commercial
situation, frequent inspection may be
necessary, and our guarantee may be
affected.
FOR USERS
2.9 If water emerges from anywhere
other than the spray head outlets, do not
use
your
shower,
TURN
ELECTRICITY and refer to the Fault
Finding section.
2.10 IT IS IMPORTANT TO CLEAN THE
SPRAY PLATE REGULARLY, particularly
in hard water areas, where this may be
necessary as often as once a week.
Failure to do so will affect the
performance of the shower and in
extreme cases may cause the pressure
relief device (PRD) to operate - see Fig.
1 and Fault Finding (p18).
Refer to the handset user instructions for
handset maintenance information.
2.11 The shower heater outlet, hose
and handset act as a vent. They must
not be blocked, obstructed, or have
connected to them any fitting not
approved by the manufacturers. The
use of unapproved accessories may
invalidate the guarantee and affect the
performance and safety of the unit.
2.12 WARNING! DO NOT USE the
shower if the HOSE IS DAMAGED in any
way; for instance if the outer covering has
parted to reveal the inner tube.
A damaged hose can suddenly restrict the
4
In the unlikely event of a problem, consult the trouble shooting chart below.
For your particular symptom follow the suggested remedies in the order given. If you
are unable to remedy the problem, CONTACT YOUR INSTALLER IN THE FIRST
INSTANCE. Do not attempt any electrical or plumbing work unless you are competent
to do so.
SYMPTOM
POSSIBLE CAUSE
1. No flow or not
A. Electrical supply to
enough flow.
B. Water control knob is
C. Water turned off at
OFF
D. SHOWER HEATER
E. There may be an
F. 'User Protect' system
9 FAULT FINDING
REMEDY
A. Ensure that the electrical supply to the shower is
shower heater off.
switched on.
B. Turn water control knob anticlockwise.
turned fully
clockwise.
C. Ensure water is fully turned on at the mains and at
mains or servicing
servicing valve in circuit.
valve.
D. If so, DO NOT USE.
SUSPECTED OF
1. Switch off immediately at isolating switch.
BEING FROZEN.
2. Turn water off at servicing valve (if fitted) or at stop
cock.
3. Contact our Service Department.
E. Disconnect handset from hose and run the shower.
outlet blockage.
1. If water flows, then handset is blocked with scale or
debris. Remember that disturbances to plumbing
elsewhere in your house, or in the street, can dislodge
debris which can find its way to the shower. Clean the
handset and spray rings/plate thoroughly.
2. If the water does not flow, remove hose from the
shower outlet.
2a If the water flows then the hose is blocked. This could
be due to damage, severe kinking or even an
obstruction. Replace with a new hose.
2b If the water does not flow, there is a blockage in the
plumbing to the shower, or the shower itself. Contact
our Service Department if the shower is considered to
be the problem.
F. Position the handset where it can spray safely and
has been activated
purge the heater of the hot water as follows:-
(temp indicators and
1. Press and hold in 'START/STOP' button.
'START/STOP' light
2. Press and hold in 'LOW' button. Water will flow from
flashing).
handset.
3. When temperature has reduced to a safe level, Low
flow and flashing lights will go out.
17
Advertisement
Table of Contents
