Table of Contents
Advertisement
Quick Links
The quality name in water heating
APPROVED SPARES STOCKISTS
Electric Water Heating Co.,
2 Horsecroft Place, Pinnacles,
Harlow, Essex CM19 5BT
Tel:
0845 0553811
E-mail: sales@ewh.co.uk
Eyre & Elliston
Unit 9 & 10, Chantry Gate Business Centre,
Springfield Road, Hayes,
Middlesex
Tel:
020 8573 0574
Parts Center
Network 65 Business Park, Bentley Wood Way,
Burnley, Lancashire BB11 5ST
Tel:
01282 834403
www.partscenter.co.uk
Newey & Eyre
Specialists Products Division
Please contact your local branch.
UK Spares Ltd.,
Tower Lane, Warmley,
Bristol BS30 8XT
Tel:
0117 961 6670
William Wilson Ltd.,
Unit 3A, 780 South Street,
Whiteinch, Glasgow G14 0SY
Tel:
0141 4341530
Due to continuous improvement and updating, specifications may be altered without prior notice.
Heatrae Sadia
Service
Hurricane Way,
Tel: (01603) 420330
Norwich,
Fax: (01603) 420349
Norfolk NR6 6EA.
email: service@heatraesadia.com
www.heatraesadia.com
Sales
Tel: (01603) 420110
Fax: (01603) 420149
email:
sales@heatraesadia.com
20
ELECTRIC SHOWER
INSTALLATION and USER INSTRUCTIONS
ref. 36 00 5641 issue 4
PROTECT
LOW FLOW
HANDSET
SHUTDOWN
PLEASE READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE
COMMENCING INSTALLATION
PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER
USER
START
STOP
HIGH
INSPECT
MEDIUM
PHASED
LOW
1
Advertisement
Table of Contents
Related Manuals for Heatrae Sadia Accolade
Summary of Contents for Heatrae Sadia Accolade
- Page 1 William Wilson Ltd., Unit 3A, 780 South Street, Whiteinch, Glasgow G14 0SY Tel: 0141 4341530 Due to continuous improvement and updating, specifications may be altered without prior notice. Heatrae Sadia Service Sales Hurricane Way, Tel: (01603) 420330 Tel: (01603) 420110...
- Page 2 SYMPTOM POSSIBLE CAUSE REMEDY Heat Thermal cutout 6. “Low Flow” exchanger A. Cartridge fuse or A. Switch off shower and isolating switch. Renew fuse or Fixing Lugs indicator not lit. miniature circuit reset mcb. If they operate a second time, contact a Printed Circuit Board (PCB) Isolating switch...
-
Page 3: Technical Specifications
SYMPTOM POSSIBLE CAUSE REMEDY CONTENTS 1 TECHNICAL SPECIFICATIONS 1. continued F. continued 4. Release ‘LOW’ and ‘START/STOP’ buttons. 1.1 CONNECTIONS 5. Press ‘START/STOP’, the shower will be reset to Internal components ......p2 previous settings. Inlet connection -15mm ext. diameter Wiring diagram ........ -
Page 4: For Installers
fitted in the pipework to the shower, in an 2 IMPORTANT INFORMATION 9 FAULT FINDING accessible place. This will be of great 2.1 Your shower is designed and tested In the unlikely event of a problem, consult the trouble shooting chart below. benefit if any maintenance work or to the very highest standards and complies complete replacement of the shower is... -
Page 5: Maintenance
MAINTENANCE flow and result in extremely hot water HOW AN INSTANT ELECTRIC being emitted from the spray head. SHOWER WORKS ‘Inspect Handset’ warning A damaged hose could completely block 2.19 When the user starts the shower by 8:4 This light will flash when it is advised the outlet of the shower;... -
Page 6: Siting And Plumbing
3 SITING AND PLUMBING Highest Position 3.1 Spend some time planning exactly Indicator lights Stop /Start button USER START where to site the shower heater and riser Riser rail PROTECT STOP and indicator light User protect rail. Bear in mind the height of people who LOW FLOW HIGH Low flow... -
Page 7: Environmental Information
3.10 Ensure there are no services such flashing. fitted in the water supply pipe to the The policy of Heatrae Sadia is one of as gas, water pipes, electrical or telephone shower. This is to allow the shower heater 5.56 Hold down the ‘START/STOP’ button... -
Page 8: Electrical Installation
5.48 The ‘MED’ and ‘LOW’ power settings INSPECT HANDSET LIGHT 4 ELECTRICAL INSTALLATION Double pole isolating switch: allow you to reduce the power used by the 5.52 This product is fitted with an pull cord or wall mounted in accordance WARNING heater and can be used at times of the with IEE regulations... -
Page 9: Cable Entry
5.35 Ensure that all three screws hold the COMMISSIONING re-tiling. If you must tile around the 5 CONNECTING TO SERVICES shower backplate to the wall firmly. shower, DO NOT grout right up to the NOTE: The first commissioning of the PREPARATION shower backplate as this makes 5.36 Strip the outer insulation sheath back... -
Page 10: Pipe Entry
PIPE ENTRY 5.16 Side Entry. You must use a straight shower heater, prior to connecting to connector with an overall length (including the shower - see Fig. 6. It may be best 5.12 Available entry points:- top, bottom, nuts and olives) of less than 42mm. to take the shower off the wall to do this.